Travis Industries GreenSmart Fireplace 564 SS Bedienungsanleitung

564 SS Fireplace

• Operation

• Maintenance

Tested and Listed by

OMNI-Test Laboratories, Inc.

Beaverton, Oregon

Report # 028-F-80-5

ANSI Z21.88a-2003

WARNING: If the information in these instructions is not followed exactly, a

fire or explosion may result causing property damage, personal

injury or loss of life.

- Do not store or use gasoline or other flammable vapors and liquids in the

vicinity of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call gas supplier from a neighbor's phone. Follow the gas

supplier's instructions.

• If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service

agency or the gas supplier.

This appliance may be installed as an OEM installation in a manufactured (mobile) home and

must be installed in accordance with the manufacturer’s instructions and the manufactured

home construction and safety standard, Title 24 CFR, Part 3280.

This appliance is only for use with the type(s) of gas indicated on the rating plate. A

conversion kit is supplied with the appliance.

Owner's Manual

Mukilteo, WA 98275

2 Introduction

Introduction

We welcome you as a new owner of a 564 SS gas fireplace. This manual details operation and

maintenance of this fireplace. Please familiarize yourself with the Owner's Manual before operating your

heater and save the manual for future reference.

Important Information

No other 564 SS gas fireplace has the same serial

number as yours. The serial number is on the listing

label that is chained to the gas control valve. This serial

number may be needed in case you require service.

Model: 564 SS Fireplace

Serial Number:

Purchase Date:

Purchased From:

traviswarranty.com

Or, mail your warranty card to:

Travis Industries House of Fire

4800 Harbour Pointe Blvd. SW

Mukilteo, WA 98275

Save Your Bill of Sale.

To receive full warranty coverage, you will

need to show evidence of the date you

purchased your heater. Do not mail your Bill

of Sale to us.

We suggest that you attach your Bill of Sale

to this page so that you will have all the

information you need in one place should

the need for service or information occur.

Installation Warnings

• Installation requirements are printed in the 564 SS Installation Manual (part

# 100-01188). All requirements in the installation manual must be met.

• Failure to follow all of the requirements may result in property damage,

bodily injury, or even death.

• This heater must be installed by a qualified installer who has gone through

a training program for the installation of direct vent gas appliances.

• This appliance must be installed in accordance with all local codes, if any;

if not, follow ANSI Z223.1 and NFPA 54(88).

• In Manufactured or Mobile Homes must conform with Manufactured Home

Construction and Safety Standard, Title 24 CFR, Part 3280, or, when such a

standard is not applicable, the Standard for Manufactured Home

Installations, ANSI/NCSBCS A225.1. This appliance may be installed in

Manufactured Housing only after the home is site located.

• The fireplace is designed to operate on natural gas, or propane (LP).

• All exhaust gases must be vented outside the structure of the living-area.

Combustion air is drawn from outside the living-area structure.

• Notify your insurance company before hooking up this fireplace.

Introduction 3

Table of Contents

Introduction and Important Information

Introduction.............................................................2

Important Information ................................................2

Installation Warnings.................................................2

Features .................................................................3

Heating Specifications...............................................3

Safety Precautions

Safety Precautions...................................................4

Operation

Before You Begin......................................................6

Location of Controls ..................................................6

Starting The Pilot Flame..............................................6

Starting the Fireplace for the First Time..........................8

Turning the Fireplace On and Off..................................8

Adjusting the Flame Height..........................................8

Adjusting the Optional Blower Speed.............................9

Normal Operating Sounds...........................................9

Normal Operating Odors.............................................9

Maintenance

Maintaining Your Fireplace's Appearance ...................... 10

Yearly Service Procedure........................................... 10

Grill Installation and Removal...................................... 11

Face Installation and Removal..................................... 12

Glass Frame Removal and Installation .......................... 13

Log Set Installation................................................... 15

Glass Cleaning......................................................... 22

Troubleshooting Table ............................................... 23

How this Fireplace Works ........................................... 24

Wiring Diagram......................................................... 25

Replacement Parts List.............................................. 25

Warranty

Warranty................................................................. 24

Optional Equipment

Optional Equipment List............................................. 27

Index

Index..................................................................... 28

Features

• Works During Power Outages (millivolt system)

• Optional Thermostat or Remote Control

• Realistic "Wood Fire" Look

• Optional Blower for Effective Heat Distribution

• Convenient Operating Controls

• Variable-Rate Heat Output

• Low Maintenance

Heating Specifications

Natural Gas Propane

Approximate Heating Capacity (in square feet)* 950 950

Maximum BTU Input Per Hour 20,500 20,500

Minimum BTU Input on Low 5,100 4,200

Steady State Efficiency** (with blowers on) 76.5 % 74.2 %

* Heating capacity will vary with floor plan, insulation, and outside temperature.

** Efficiency rating is a product thermal efficiency rating determined under continuous operation

independent of installed system.

4 Safety Precautions

IF YOU SMELL GAS:

* Do not light any appliance

* Extinguish any open flame

* Do not touch any electrical switch or plug or unplug anything

* Open windows and vacate building

* Call gas supplier from neighbor's house, if not reached, call fire

department

This unit must be installed by a qualified installer to prevent the possibility of an explosion.

Your dealer will know the requirements in your area and can inform you of those people

considered qualified. The room heater should be inspected and cleaned before use and

at least annually by a qualified service person. More frequent cleaning may be required

due to excessive lint from carpeting, bedding material, etc.

The instructions in this manual must be strictly adhered to. Do not use makeshift methods

or compromise in the installation. Improper installation will void the warranty and safety

listing.

For LPG only | Pout 11” W.C.

Look for this label:

If the label is present, the

heater is equipped for LP

(propane). If the label is

absent, the heater is equipped

for NG (natural gas).

This heater is either approved for natural gas

(NG) or for propane (LP). Burning the incorrect

fuel will void the warranty and safety listing and

may cause an extreme safety hazard. Direct

questions about the type of fuel used to your

dealer. Check the label and flame adjust knob

on the gas control valve.

Contact your local building

officials to obtain a permit and

information on any installation

restrictions or inspection

requirements in your area.

Notify your insurance company

of this heater as well.

If the flame becomes sooty, dark

orange in color, or extremely tall,

do not operate the heater. Call

your dealer and arrange for

proper servicing.

It is imperative that control

compartments, screens, or

circulating air passageways of

the heater be kept clean and

free of obstructions. These

areas provide the air necessary

for safe operation. ?Do not operate the heater if it is

not operating properly in any

fashion or if you are uncertain.

Call your dealer for a full

explanation of your heater and

what to expect.

Gas

Do not store or use gasoline or

other flammable liquids in the

vicinity of this heater.

AAAAA

Do not operate if any portion of

the heater was submerged in

water or if any corrosion occurs.

Immediately call a qualified

service technician to inspect the

appliance and to replace any part

of the control system and any gas

control that has been under

water.

Safety Precautions 5

Do not place clothing or other

flammable items on or near the

heater. Because this heater can

be controlled by a thermostat

there is a possibility of the heater

turning on and igniting any items

placed on or near it.

Light the heater using the built-in

piezo igniter. Do not use

matches or any other external

device to light your heater.

Allow the heater to cool before

carrying out any maintenance or

cleaning.

The viewing glass should be

opened only for lighting the

pilot or conducting service. Do

not operate with cracked,

broken, or removed glass.

Any safety screen or guard

removed for servicing must be

replaced prior to operating the

heater.

Never remove, replace, modify or

substitute any part of the heater

unless instructions are given in

this manual. All other work must

be done by a trained technician.

Don't modify or replace orifices.

Operate the heater according to

the instructions included in this

manual.

If the main burners do not start

correctly turn the gas off at the

gas control valve and call your

dealer for service.

The pilot flame must contact the

thermopile and thermocouple

(see the illustration to the left). If

it does not, turn the gas control

valve to "OFF" and call your

dealer.

This unit is not for use with solid

fuel

Do not place anything inside the

firebox (except the included

fiber logs).

If the fiber logs become

damaged, replace with Travis

Industries log set.

This

Manual

Do not throw this manual away.

This manual has important

operating and maintenance

instructions that you will need at a

later time. Always follow the

instructions in this manual.

Children and adults should be

alerted to the hazards of high

surface temperature and should

stay away to avoid burns or

clothing ignition. Young children

should be supervised when

they are in the same room as the

heater.

Travis Industries, Inc.

grants no warranty, implied

or stated, for the

installation or maintenance

of your heater, and

assumes no responsibility

of any consequential

damage(s).

Instruct everyone in the house

how to shut gas off to the

appliance and at the gas main

shutoff valve. The gas main

shutoff valve is usually next to

the gas meter or propane tank

and requires a wrench to shut

off.

6 Operation

Before You Begin

• Read this entire manual before you use your new fireplace (especially the section "Safety

Precautions" on pages 4 & 5). Failure to follow the instructions may result in property damage, bodily

injury, or even death.

Location of Controls

AAAAAAAAA

AAAAAAAAAA

Lift the control cover up and swing it

forward to access the controls.

Pilot Igniter

ON/OFF Switch

Flame Adjust Knob Gas Control Knob

An instruction card for operating

the fireplace is attached to the

inside of the fireplace here.

Replace it for easy reference.

The Pilot Flame can be

found under the rear log .

Comfort Control

Gas Control Valve

Optional Blower Control

Optional Accent Light

Pilot Igniter The pilot igniter is used only to start the pilot. When pressed, it sends an

electrical charge to the pilot assembly. This creates a blue spark directly next

to the pilot, igniting the pilot flame.

On/Off Switch This control is used to turn the fireplace burners on and off.

Gas Control Knob This knob is used to control gas to the fireplace and for starting the pilot.

There are three positions, ON, OFF, & PILOT. The pointer to the left of the

knob indicates the position this knob is in.

Flame Adjust Knob This knob controls the flame height from low ("LO") to high ("HI"). The pointer

above the knob points to the position this knob is in.

Comfort Control This lever turns the rear burner on and off.

NOTE: THIS IS NOT A SHUTOFF VALVE.

Optional Blower Control This knob controls the speed of the optional internal convection blower

that pushes heated air into the room.

Optional Accent Light This knob controls the optional accent lights located behind

the logs.

Operation 7

Starting The Pilot Flame

The pilot flame is required to ignite the main

burners (it also plays a safety role). It should be

left on once lit. It will stay lit unless the gas

control valve is turned to "OFF". However, the

pilot will go out if the gas is shut off, the

propane tank runs out (or low) or if the stove

malfunctions. If the pilot turns off frequently,

call your dealer for information. To start the

pilot follow the directions below:

WARNING:

When lighting or re-lighting the pilot,

the glass must be removed (see page

10).

aRemove the glass (see page 10 for details).

bPush the gas control knob in slightly and turn

it to the "OFF" position. The knob will not

turn from "ON" to "OFF" unless the knob is

depressed slightly. Wait five minutes to let

any gas that may have accumulated inside

the firebox escape. If you smell leaking gas,

follow the directions on the cover "IF YOU

SMELL GAS".

cTurn the gas control knob to the "PILOT"

position and press the knob in, this will allow

gas to flow to the pilot light. Press the

button on the pilot igniter repeatedly until

you see the pilot light.

WARNING:

If the pilot does not light after 15

seconds, release the knob and call your

dealer for service. Do not attempt to

light pilot until service has been

performed.

NOTE:

You may wish to remove the log set to

gain a better view of the pilot (see page

15).

dKeep the gas control knob depressed for 30

seconds once it is lit.

eRelease the gas control knob. If the pilot

goes out, repeat step C. If the pilot refuses

to stay lit, call your dealer for service. With

the pilot lit, proceed to step “f”.

fReplace the glass.

gTurn the gas control knob counter-clockwise

to "ON". The pilot is now lit and the heater

can be turned on and off.

30 seconds

PILOT

IGNITER

5 minutes

AAA

AAAAAAA

AAA

AAAAAAA

AAA

AAAAAAA

AAA

AAAAAAA

8 Operation

Starting the Fireplace for the First Time

• Burn the heater at a high setting with the blower off for an extended period (up to 48 hours). This will

cure the painted surfaces. Fumes from the paint curing and oil burning off the steel will occur. This is

normal. We recommend opening a window to vent the room.

• Condensation may appear on the glass each time you start the fireplace - this is normal.

• Blue Flames will occur on the fireplace when it first comes on. After fifteen minutes the flames will

turn a more realistic yellow and orange color.

• Certain installations use a remote "wall switch" to turn the fireplace on and off. If this is the case, leave

the ON/OFF switch "ON".

Turning the Fireplace On and Off

After the pilot has been started...

OFF

ROOM TEMP

°F

SETTEMP

TIMER

MIN

Time

Set

Time

Cancel

A switch is provided behind

the control cover (below

the firebox).

An optional remote may be

used (see the instructions

included with the remote).

An optional wall thermostat

may be used to control the

temperature.

A wall switch may be

used to turn the

fireplace on and off.

NOTE FOR REMOTES, THERMOSTATS, OR WALL SWITCHES:

The on/off switch on the fireplace may be required to be left in the ON or OFF position for the fireplace to

operate. Consult your installer or dealer for details.

• Do not place any combustible items on top of or directly in front of the fireplace, even temporarily. The

optional thermostat may start the fireplace causing a combustible item to ignite.

• If the fireplace turns on and off frequently while using the thermostat, you may want to adjust the flame

height down until it produces just enough heat needed.

Adjusting the Flame Height

• Your fireplace has an adjustable flame to tailor the look and heat output to your specific needs. It is

adjusted by turning the middle dial on the gas control valve.

Flame Height

Adjustment Knob

Index Mark

Turn counter-clockwise to adjust the flame higher, clockwise to lower.

Operation 9

Adjusting the Optional Blower Speed

The blower helps transfer heat from the heater into the room. It will not turn on until the heater is up to

temperature (approximately 10 minutes after starting). See the illustration below for instructions on

adjusting the blower speed.

NOTE: With the rear burner off (comfort control), the heater may not become hot enough for the

blower to turn on.

OFF

Turn the dial all the

way counter-clockwise

until it clicks off.

HIGH

The high position is all the

way counter-clockwise,

without clicking off.

LOW

Turn the dial all the

way clockwise.

Normal Operating Sounds

Gas Control Valve

As the gas control valve is turned

on and off you will hear a dull

clicking sound. This is the valve

Blower Snap Disk

This part can produce a

clicking sound as it turns

the blower on and off.

The appliance may creak with change of

temperature -- THIS IS NORMAL.

Pilot Flame

The pilot flame, which remains on,

makes a very slight "whisper" sound.

Blowers

This heater has optional blowers to push

heated air into the room. You will hear the

sound of air movement that increases as

the speed is increased.

Extinction Pops

It is not unusual, especially on Propane

(LP) appliances, to experience a "pop"

when the burner is shut off.

Normal Operating Odors

This appliance has several areas that reach high temperatures. Dust or other particles on these areas may

burn and create an odor. This is normal during start-up. You may notice the smell is more acute if the

appliance was left idle for a long period.

10 Maintenance

Maintaining Your Fireplace's Appearance

Fingerprints or other marks left on the optional plated surface may become etched in place if they are not

wiped clean prior to turning the fireplace on. Clean the plated surface with denatured alcohol and a soft

cloth (with the fireplace cool). Other cleaners may leave a film that may become etched into the surface.

Yearly Service Procedure

• Failure to inspect and maintain the fireplace may lead to improper combustion and a potentially dangerous

situation. We recommend the following procedures be done by a qualified technician.

1. Check the pilot flame. It should touch approximately 3/8" of the top of the thermopile and touch the top of the

thermocouple (see illustration below). If it does not, contact your dealer for service.

2. Shut off gas to the fireplace by turning the gas control knob to "OFF" (see step A under "Starting the Pilot" on

page 7). Let the fireplace cool for 15 minutes. Remove the glass (see page 10).

3. Remove the log set (NOTE: the logs are very fragile - see page 15). If severely deteriorated, replace.

Check the logs for sooting. A small amount of soot along the bottom of the logs is normal. If excessive sooting

is found, the fireplace will require adjustment. Contact your dealer.

4. Inspect the burner and remove any debris.

• Make sure the burner is not warped, cracked, or damaged.

• Check the firebox and area around the pilot to make sure there is no warping or damage.

• If any problem is found, discontinue use and contact your dealer for service.

Check the burner holes.

Make sure the burners are not

warped or damaged.

Thermopile

Pilot Hood

Thermocouple

Before Disassembly - Check the pilot flame. It

should touch the thermocouple and thermopile.

Check the walls and ceiling

of the firebox for

deterioration.

5. Replace the log set. Clean and replace the glass (see Glass Cleaning on page 22). If the glass is damaged,

replace. Make sure the gasket along the perimeter of the glass contacts the face of the firebox and forms an air-

tight seal. If it does not, re-align or replace the gasket to insure an air-tight seal.

6. Inspect the area behind the access door. Clean if necessary. Check the gas control valve and the gas lines. If

damage is found, discontinue use and contact your dealer for service. Clean the air channels, ducts, and blower

(if applicable).

7. Start the pilot and turn on the main burner. The flames should be orange/yellow and not touch the top of the

firebox. If the pilot or main burners do not burn correctly, contact your dealer for service. Monitor the blower

operation.

8. Remove any debris or vegetation near the vent termination. Contact your dealer if any sooting or deterioration is

found near the vent termination.

Andere Handbücher für GreenSmart Fireplace 564 SS

Inhaltsverzeichnis

Andere Travis Industries Kamin im Innenbereich Handbücher

Travis Industries

Travis Industries 616 GSR Bedienungsanleitung

Travis Industries

Travis Industries Freedom Bay Bedienungsanleitung

Travis Industries

Travis Industries 864 Clean Face Bedienungsanleitung

Travis Industries

Travis Industries GreenSmart Fireplace 564 SS Bedienungsanleitung

Travis Industries

Travis Industries DVS EF Insert Bedienungsanleitung

Travis Industries

Travis Industries DVS FIREPLACE Bedienungsanleitung

Travis Industries

Travis Industries 430 GSR2 Bedienungsanleitung

Travis Industries

Travis Industries DVL GSR Bedienungsanleitung

Travis Industries

Travis Industries Space Saver GreenSmart 2 564 Bedienungsanleitung

Travis Industries

Travis Industries 864 TRV GS Bedienungsanleitung

Travis Industries

Travis Industries ProBuilder 54 Linear Bedienungsanleitung

Travis Industries

Travis Industries 564 Cleanface Bedienungsanleitung

Travis Industries

Travis Industries 864 HO GS Bedienungsanleitung

Travis Industries

Travis Industries DVS Insert EF II Bedienungsanleitung

Travis Industries

Travis Industries 31 DVI GSB2 Bedienungsanleitung

Travis Industries

Travis Industries 430 Mod-Fyre GSR2 Bedienungsanleitung

Travis Industries

Travis Industries DVS GSR Bedienungsanleitung

Travis Industries

Travis Industries 564 HO Bedienungsanleitung

Travis Industries

Travis Industries DVL GSR2 NB Bedienungsanleitung

Travis Industries

Travis Industries 864 TRV Bedienungsanleitung

Travis Industries

Travis Industries 864 TRV Bedienungsanleitung

Travis Industries

Travis Industries Large Flush Bedienungsanleitung

Travis Industries

Travis Industries Xtreme 6020 Bedienungsanleitung

Travis Industries

Travis Industries 21 TRV GreenSmart Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch