Travis Industries Xtrordinair ProBuilder 36 CleanFace MV Bedienungsanleitung

ProBuilder 36/42

CleanFace MV

Owner’s Manual

WARNING: FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could result in serious injury, death, or property damage.

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any

other appliance.

- WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Leave the building immediately

• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency or the gas supplier.

HOT GLASS WILL CAUSE

BURNS

DO NOT TOUCH GLASS

UNTIL COOLED

NEVER ALLOW CHILDREN

TO TOUCH GLASS

A barrier designed to reduce the risk of burns from

the hot viewing glass is provided with this appliance

and shall be installed for the protection of children

and other at-risk individuals.

Tested and Listed by

Report # 0028GF115S

Omni-Test Laboratories, Inc.

Portland, Oregon

ANSI Z21.88-2016

CSA 2.33-2016

CSA 2.17-2017

 Operation

 Maintenance

This appliance may be installed in an aftermarket, permanently located, manufactured home

(USA only) or mobile home, where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate. A conversion

kit is supplied with the appliance.

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

Travis Industries, Inc. 12521 Harbour Reach Dr., Mukilteo, WA 98275 www.travisproducts.com



2 Table of Contents

Introduction

We welcome you as a new owner of a ProBuilder gas fireplace. This manual details operation and

maintenance of this fireplace. Please familiarize yourself with the Owner's Manual before operating your

heater and save the manual for future reference.

Important Information

No other ProBuilder gas fireplace has the same serial

number as yours. The serial number is on the listing

label that is chained to the gas control valve. This

serial number may be needed in case you require

service.

Model: 36 ProBuilder CF MV_____

42 ProBuilder CF MV_____

Serial Number:

Purchase Date:

Purchased From:

traviswarranty.com

Save Your Bill of Sale.

To receive full warranty coverage, you will

need to show evidence of the date you

purchased your heater. Do not mail your Bill

of Sale to us.

We suggest that you attach your Bill of Sale

to this page so that you will have all the

information you need in one place should the

need for service or information occur.

Installation Warnings

 Installation requirements are printed in the ProBuilder Installation Manual. All

requirements in the installation manual must be met.

 Failure to follow all of the requirements may result in property damage, bodily injury,

or even death.

 This heater must be installed by a qualified installer who has gone through a training

program for the installation of direct vent gas appliances.

 This appliance must be installed in accordance with all local codes, if any; if not,

follow ANSI Z223.1 and NFPA 54(88). In Australia follow AS/NZS 5601.1.

 In Manufactured or Mobile Homes must conform with Manufactured Home

Construction and Safety Standard, Title 24 CFR, Part 3280, or, when such a standard

is not applicable, the Standard for Manufactured Home Installations, ANSI/NCSBCS

A225.1. This appliance may be installed in Manufactured Housing only after the

home is site located.

 The fireplace is designed to operate on natural gas, or propane (LP).

 All exhaust gases must be vented outside the structure of the living-area.

Combustion air is drawn from outside the living-area structure.

 Notify your insurance company before hooking up this fireplace.

Introduction 3

Table of Contents



Introduction ................................................... 2

Important Information ................................... 2

Installation Warnings .................................... 2

Table of Contents .......................................... 3

Features ......................................................... 3

Heating Specifications .................................. 3

Before You Begin .......................................... 6

Location of Controls ..................................... 6

Starting the Pilot ............................................ 7

Starting the Heater for the First Time .......... 8

Turning the Heater On and Off ..................... 8

Adjusting the Flame Height .......................... 8

Adjusting the Blower Speed (Optional) ...... 9

Normal Operating Odors .............................. 9

Power Outages .............................................. 9

Glass Frame Removal and Installation .............. 10

ProBuilder 36 Log Set Installation ............. 13

ProBuilder 42 Log Set Installation ............. 19

Ember bed Glass and Ember Material

Installation (GSR2 ONLY) ........................... 25

Ember bed Glass Installation ............................ 25

Ember Material Installation (GSR2 ONLY) ........ 26

Ember Installation.............................................. 27

Rock Wool Placement ....................................... 27

Maintaining Your Heater's Appearance .... 28

Cleaning The Glass .............................................. 28

Cleaning the Fireplace .......................................... 28

Yearly Service Procedure ........................... 29

Troubleshooting Table ............................... 30

Replacement Parts List .............................. 31

Wiring Diagram ........................................... 32

Optional Blower Wiring ...................................... 32

36 PB Safety Label ........................................... 33

42 PB Safety Label ........................................... 34

CONDITIONS & EXCLUSIONS ................... 35

IF WARRANTY SERVICE IS NEEDED: ...... 35

Index ............................................................. 36

Features

 Works During Power Outages

 Contemporary Look

 Optional Blower for Heat Distribution

 Optional Remote Thermostat

 Standing Pilot

 Variable-Rate Heat Output

 Low Maintenance

Heating Specifications

Natural Gas Propane

ProBuilder 36 CF Approximate Heating Capacity (in square feet)* Up to 1,150 Up to 1,150

Maximum BTU Input Per Hour 25,000 24,000

ProBuilder 42 CF Approximate Heating Capacity (in square feet)* Up to 1,750 Up to 1,750

Maximum BTU Input Per Hour 35,000 35,000

* Heating capacity will vary with floor plan, insulation, and outside temperature.

4 Safety Precautions

IF YOU SMELL GAS:

* Do not light any appliance

* Extinguish any open flame

* Do not touch any electrical switch or plug or unplug anything

* Open windows and vacate building

* Call gas supplier from neighbor's house, if not reached, call fire department

This unit must be installed by a qualified installer to prevent the possibility of an explosion.

Your dealer will know the requirements in your area and can inform you of those people

considered qualified. The room heater should be inspected and cleaned before use and at

least annually by a qualified service person. More frequent cleaning may be required due

to excessive lint from carpeting, bedding material, etc.

The instructions in this manual must be strictly adhered to. Do not use makeshift methods

or compromise in the installation. Improper installation will void the warranty and safety

listing.

This heater is either approved for natural gas (NG) or for propane (LP). Burning

the incorrect fuel will void the warranty and safety listing and may cause an

extreme safety hazard. Direct questions about the type of fuel used to your dealer.

Check for a label on the flame adjust knob on the gas control valve (this is the best

place to check). You may also check for a label on the gas control valve body.

Contact your local building

officials to obtain a permit and

information on any installation

restrictions or inspection

requirements in your area.

Notify your insurance company

of this heater as well.

If the flame becomes sooty, dark

orange in color, or extremely tall,

do not operate the heater. Call

your dealer and arrange for

proper servicing.

It is imperative that control

compartments, screens, or

circulating air passageways of

the heater be kept clean and

free of obstructions. These

areas provide the air necessary

for safe operation.

Do not operate the heater if it is

not operating properly in any

fashion or if you are uncertain.

Call your dealer for a full

explanation of your heater and

what to expect.

Do not store or use gasoline or

other flammable liquids in the

vicinity of this heater.

Do not operate if any portion of

the heater was submerged in

water or if any corrosion occurs.

Immediately call a qualified

service technician to inspect the

appliance and to replace any part

of the control system and any

gas control that has been under

water.

Gas





Safety Precautions 5

Do not place clothing or other

flammable items on or near the

heater. Because this heater can

be controlled by a thermostat

there is a possibility of the

heater turning on and igniting

any items placed on or near it.

Light the heater using the built-in

igniter. Do not use matches or

any other external device to light

your heater.

Allow the heater to cool before

carrying out any maintenance or

cleaning.

The viewing glass should be

opened only for conducting

service. Do not operate with

cracked, broken, or removed

glass.

Any safety screen or guard

removed for servicing must be

replaced prior to operating the

heater.

Never remove, replace, modify or

substitute any part of the heater

unless instructions are given in

this manual. All other work must

be done by a trained technician.

Don't modify or replace orifices.

Operate the heater according to

the instructions included in this

manual.

If the main burners do not start

correctly turn the gas off at the

gas control valve and call your

dealer for service.

Instruct everyone in the house

how to shut gas off to the

appliance and at the gas main

shutoff valve. The gas main

shutoff valve is usually next to

the gas meter or propane tank

and requires a wrench to shut off.

This unit is not for use with solid

fuel

Do not place anything inside the

firebox (except the crushed

glass).

If any component becomes

damaged, replace with Travis

Industries components.

Do not throw this manual away.

This manual has important

operating and maintenance

instructions that you will need at

a later time. Always follow the

instructions in this manual.

Children and adults should be

alerted to the hazards of high

surface temperature and should

stay away to avoid burns or

clothing ignition. Young children

should be supervised when they

are in the same room as the

heater.

Travis Industries, Inc. grants no

warranty, implied or stated, for

the installation or maintenance of

your heater, and assumes no

responsibility of any

consequential damage(s).







This

Manual

6 Operation

Before You Begin

 Read this entire manual before you use your new fireplace (especially the section "Safety

Precautions" on pages 4 & 5). Failure to follow the instructions may result in property damage, bodily

injury, or even death.

Location of Controls

There is a door on the lower portion of the screen assembly to provide access to the manual controls on

the fireplace. The door is held closed by two magnets. Open the door by gently pulling outward on the

upper portion of the lower trim.

On/Off Switch This control is used to turn the heater on and off.

Pilot Igniter The pilot igniter is used only to start the pilot. When pressed, it sends an

electrical charge to the pilot assembly. This creates a blue spark directly

next to the pilot, igniting the pilot flame.

Gas Control Knob This knob is used to control gas to the heater and for starting the pilot. There

are three positions, ON, OFF, & PILOT. The pointer to the left of the knob

indicates the position this knob is in.

Flame Adjust Knob This knob controls the flame height from low ("LO") to high ("HI"). The

pointer above the knob points to the position this knob is in.

Optional Remote Receiver The receiver is used in conjunction with the optional remote thermostat. It is

used to control the remote and replaces the on/off switch for direct operation.

Optional Blower Dial This dial controls the speed of the internal convection blower that pushes the

heated air into the room.

Optional Light Dial This dial controls the brightness of the optional accent lights (if applicable).

Rotate the Control Door Down to

Access Controls



Shutoff Valve

(accessible with

screen removed)

Pilot Igniter

On/Off Switch

Optional Blower Dial

Optional Remote Receiver

Gas Control Knob

Flame Adjust Knob

Optional EmberLight Dial

Operation 7

Starting the Pilot

Make sure the barrier screen is in place before starting the pilot.

The pilot flame is required to ignite the main

burners (it also plays a safety role). It should

be left on once lit. It will stay lit unless the gas

control valve is turned to "OFF". However, the

pilot will go out if the gas is shut off, the

propane tank runs out (or low) or if the stove

malfunctions. If the pilot turns off frequently,

call your dealer for information. To start the

pilot follow the directions below:

WARNING:

a Make sure the barrier screen is in place

(see page 10 for details).

b Push the gas control knob in slightly and

turn it to the "OFF" position. The knob will

not turn from "ON" to "OFF" unless the knob

is depressed slightly. Wait five minutes to

let any gas that may have accumulated

inside the firebox escape. If you smell

leaking gas, follow the directions on the

cover "IF YOU SMELL GAS".

c Turn the gas control knob to the "PILOT"

position and press the knob in, this will allow

gas to flow to the pilot light. Press the

button on the pilot igniter repeatedly until

you see the pilot light.

WARNING:

If the pilot does not light after 15 seconds,

release the knob and call your dealer for

service. Do not attempt to light pilot until

service has been performed.

d Keep the gas control knob depressed for 30

seconds once it is lit.

e Release the gas control knob. If the pilot

goes out, repeat step C. If the pilot refuses

to stay lit, call your dealer for service. With

the pilot lit, proceed to step “f”.

f Turn the gas control knob counter-clockwise

to "ON". The pilot is now lit and the heater

can be turned on and off.

30 seconds

PILOT

IGNITER

5 minutes

8 Operation

Starting the Heater for the First Time

 Burn the heater at a high setting with the blower off for an extended period (up to 48 hours). This will

cure the painted surfaces. Fumes from the paint curing and oil burning off the steel will occur. This

is normal. We recommend opening a window to vent the room.

 Condensation may appear on the glass each time you start the heater - this is normal.

 Blue Flames will occur on the heater when it first comes on. After fifteen minutes the flames will turn

a more realistic yellow and orange color.

Turning the Heater On and Off

 Do not place any combustible items on top of or directly in front of the heater, even temporarily. The

optional thermostat may start the heater causing a combustible item to ignite.

 If the heater turns on and off frequently while using the thermostat, you may want to adjust the flame

height down until it produces just enough heat needed.

Adjusting the Flame Height

 Your heater has an adjustable flame to tailor the look and heat output to your specific needs. It is

adjusted by turning the middle dial on the gas control valve.

ON/OFF SWITCH

Use this switch to turn the main

burner on and off manually.

fter the pilot has been started...

OPTIONAL REMOTE THERMOSTAT

See the instructions included with the remote

for details on operation.

°F

Flame Height

Adjustment Knob

Index Mark

Turn counter-clockwise to adjust the flame higher, clockwise to lower.

Operation 9

Adjusting the Blower Speed (Optional)

The optional blower helps transfer heat from the heater into the room. It will not turn on until the heater is

up to temperature (approximately 10 minutes after starting). See the illustration below for instructions on

adjusting the blower speed.

Normal Operating Odors

This appliance has several areas that reach high temperatures. Dust or other particles on these areas

may burn and create an odor. This is normal during start-up. You may notice the smell is more acute if

the appliance was left idle for a long period.

Power Outages

The heater will work if household current (AC power) is disconnected.

10 Maintenance

Glass Frame Removal and Installation

A barrier designed to reduce the risk of burns from the hot viewing glass is provided

with this appliance and shall be installed for the protection of children and other at-risk

individuals.

If the barrier becomes damaged, the barrier shall be replaced with the manufacturer’s

barrier for this appliance.

The appliance must be completely cool before removing the glass.

Do not strike or slam the glass.

Warning: Do not operate appliance with the glass front removed, cracked or broken.

Replacement of the glass should be done by a licensed or qualified service person.

 Remove the screen-trim assembly by lifting the assembly up slightly and tilting it toward you. The

mounting hooks on the back of the assembly will disengage the fireplace. Set the assembly aside for

reinstallation.

NOTE: Opening the access door on the front of the assembly allows for an easy location to get a secure grip

on the assembly for removal

Replacement Barrier Part #

36 CF ProBuilder 270-01022

42 CF ProBuilder 270-01024

Top Corner Bottom Corner

Bottom hook

engages this slot in

bracket

Top hook engages

this slot in bracket

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Travis Industries Kamin im Innenbereich Handbücher

Travis Industries

Travis Industries 564 Clean Face GSR2 Bedienungsanleitung

Travis Industries

Travis Industries Revere Fireplace Insert Bedienungsanleitung

Travis Industries

Travis Industries 864 HO NB GSR2 Bedienungsanleitung

Travis Industries

Travis Industries GreenSmart Fireplace 564 SS Bedienungsanleitung

Travis Industries

Travis Industries 564 Bedienungsanleitung

Travis Industries

Travis Industries Maverick Bedienungsanleitung

Travis Industries

Travis Industries GreenSmart 864 HO Bedienungsanleitung

Travis Industries

Travis Industries 864 HO NB GSR2 Bedienungsanleitung

Travis Industries

Travis Industries 864 HH Bedienungsanleitung

Travis Industries

Travis Industries 42 ProBuilder MV Bedienungsanleitung

Travis Industries

Travis Industries DVL Insert EF II Bedienungsanleitung

Travis Industries

Travis Industries 616 GSR Bedienungsanleitung

Travis Industries

Travis Industries Shadowbox Black Bedienungsanleitung

Travis Industries

Travis Industries Cleanface 864 Bedienungsanleitung

Travis Industries

Travis Industries Avalon Ashpan Bedienungsanleitung

Travis Industries

Travis Industries 864 TRV Bedienungsanleitung

Travis Industries

Travis Industries 430 Mod-Fyre GSR2 Bedienungsanleitung

Travis Industries

Travis Industries LOPI X Bedienungsanleitung

Travis Industries

Travis Industries FIREPLACE XTRORDINAIR 864 HO EF GSR2 Bedienungsanleitung

Travis Industries

Travis Industries DaVinci Bedienungsanleitung

Travis Industries

Travis Industries 21 TRV GreenSmart Bedienungsanleitung

Travis Industries

Travis Industries DVL EF Bedienungsanleitung

Travis Industries

Travis Industries 33 DVI GSB2 Insert Bedienungsanleitung

Travis Industries

Travis Industries Flush Wood Plus Insert Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch