Travis Industries Lopi Answer Bedienungsanleitung

Rear Blower Installation Instructions

99000138

Page 1 of 6 17601035 - 8/18/10 © Travis Industries, Inc.

Compatibility (Freestanding Models Only)

• Lopi Answer • Lopi Endeavor • Lopi Liberty • Lopi Leyden

• Avalon Pendleton (745/790) • Avalon Rainier (945/990) • Avalon Olympic (1190) • Avalon Arbor

• 1250 Wood Stove • 1750 Wood Stove

Packing List

• Rear Blower • Snap Disk Assembly • Snap Disk Hanger • Three 1/4" 20 Thread Cutting Screws

Operating Instructions

The blower will not turn on until the appliance is up to temperature. Once up to temperature, the blower will

operate at the speed determined by the position of the blower knob (see the illustration below). The blower

shuts off once the appliance cools.

Installation Instructions (All Except Leyden, Arbor, and 1750)

1. Install the stove legs or pedestal. Remove the two rear blower knock-outs underneath the base (see the

illustration below).

2. For the Endeavor and Liberty follow step 2B. For all other models, follow step 2A.

2A Install the snap disk assembly into the left side convection chamber following the directions below.

OFF

Turn the knob

all the way

counter-

clockwise to

turn off.

HIGH

Turn the knob

clockwise from

the off position

until it clicks.

LOW

Turn the knob

all the way

clockwise to

turn to low.

Outside Air Knock-Out

for standard pedestals

Drop Chute Knock-Out

- found on Olympic

(1190) and Rainier (990)

only.

Rear Blower Knock-Outs

Ashpan Pedestal/Air Boot

Outside Air Knock-Out

FRONT OF STOVE

REMOVE THESE KNOCK-OUTS

Ashlip

Bend these legs on

the snap disk if it

does not fit tightly

Wedge the snap disk

directly in front of the

stiffener on the left side.

Twist the wires together and feed them

through the convection chamber and

out of the knockout removed in step 1.

Snap Disk

Assembly

Rear Blower Installation Instructions

99000138

Page 2 of 6 17601035 - 8/18/10 © Travis Industries, Inc.

2A Secure the snap disk wires in place following the directions below. Go to step 3.

NOTE: The wires must be properly secured to prevent the wire from

contacting the firebox and shorting out the blower circuit.

2B (Liberty, Endeavor only) Install the snap disk assembly inside of the heat shield following the directions

below. Secure the snap disk wires in place following the directions below.

Secure the snap disk wires in place following the directions below.

NOTE: The wires must be properly secured to prevent the wire from

contacting the firebox and shorting out the blower circuit.

Slide the wire clip over the

edge of the strip of metal

between the two knock-outs.

Feed the two snap

disk wires into the

eye of the wire clip.

Then carefully

remove all slack from

the wire, making sure

not to dislodge the

snap disk. Pinch the

eye of the wire clip to

secure the wires.

Wire Clip

Snap Disk

Wires

Hang the snap disk assembly in

the space between the stove

and rear heat shield on the left

side. Bend the legs of the

assembly to ensure a tight fit.

Wire Clip

Feed the two snap

disk wires into the

eye of the wire clip.

Then carefully

remove all slack from

the wire, making sure

not to dislodge the

snap disk. Pinch the

eye of the wire clip to

secure the wires.

Snap Disk Wires

Rear Blower Installation Instructions

99000138

Page 3 of 6 17601035 - 8/18/10 © Travis Industries, Inc.

3. Place the blower near the bottom rear edge of the stove. Attach the quick-connects from the snap disk

assembly to the quick-connects on the blower. Push any slack wire into the blower box. Attach the

blower following the directions below.





Endeavor & Liberty:

Feed the two wires from

the blower through this

hole before attaching the

quick-connects.

All Other Models:

Feed the wires

directly upwards



NOTE:

Prior to attaching the blower, tuck all excess

wire into the area inside the blower.

The blower attaches to the stove with the three

included screws. Use a 3/8” socket driver or wrench.

HINT:

Attach the screws to the back of the stove prior to

attaching the blower. This will cut the threads and

ease installation.

Plug the power cord into

a 110 V. outlet after

installing the blower.

NOTE:

Prior to attaching the

blower, tuck all excess

wire into the area inside

the blower.

Attach the quick-connects

leading from the snap disk to the

quick-connects from the blower.

Rear Blower Installation Instructions

99000138

Page 4 of 6 17601035 - 8/18/10 © Travis Industries, Inc.

1750 Installation Instructions

Attach the wires from

the thermodisk to the

wires from the blower.

Attach the blower to the stove with the

three screws included with the blower.

3/8" Wrench

Remove these two knock-outs on

the bottom of the stove (use a

screwdriver to pry them out).

Plug the blower in. Do not route the power cord under or over the stove or in a

location where it may become damaged.

Position the blower near the rear of the stove. Tuck all excess wire into the

blower box, making sure it does not contact any moving parts. Make sure when

installing the blower, these wires do not become loose.

Snap Disk

Assembly

Snap Disk

Extender

Ashlip

Wedge the snap disk into

the convection channel

so. Bend the legs on the

extender, if necessary, so

the snap disk contacts the

firebox.

Twist the wires together,

feed them through the

convection chamber, out

the knockout, and attach to

the leads on the blower.

Disconnect these wires

to install the extender

(re-connect after the

extender is attached).

Place the snap disk assembly over the snap disk extender

(included with the stove) and bend these tabs to secure.

Rear Blower Installation Instructions

99000138

Page 5 of 6 17601035 - 8/18/10 © Travis Industries, Inc.

Leyden and Arbor Installation Instructions – Prior to Rev 005

The following instructions are for Leyden and Arbor wood stoves that do not have the built in

thermodisk (serial # 1110-009119 or less for Leyden, serial # 1307-003085 or less for Arbor).

Route the wires on the

outside of the stove, behind

the convection jacket.

Tuck the thermodisk into place. It

wedges between the rear heat sheild

and the cast iron firebox.

Bend the legs of the

thermodisk bracket to

make it 1-1/2” deep.

1-1/2”

3/8" Wrench

Plug the blower in. Do not route the power cord under or over the stove or in a

location where it may become damaged.

Route the wires from the blower through the hole

in the back of the blower housing. Attach these

wires to the thermodisk wires.

Position the blower near the rear of the stove. Tuck all excess wire into the

blower box, making sure it does not contact any moving parts. Make sure when

installing the blower, these wires do not become loose.

Attach the blower to the

stove with the three screws

included with the blower.

Rear Blower Installation Instructions

99000138

Page 6 of 6 17601035 - 8/18/10 © Travis Industries, Inc.

Leyden and Arbor Installation Instructions –Rev 005 or Later

The following instructions are for Leyden and Arbor wood stoves with the built in thermodisk

(serial # 1110-009120 or greater for Leyden, serial # 1307-003086 or greater for Arbor).

Andere Handbücher für Lopi Answer

Dieses Handbuch passt für folgende Modelle

Andere Travis Industries Holzofen Handbücher

Travis Industries

Travis Industries Lopi 1750 Republic Bedienungsanleitung

Travis Industries

Travis Industries Lopi Answer Bedienungsanleitung

Travis Industries

Travis Industries Endeavor Bedienungsanleitung

Travis Industries

Travis Industries Lopi Rockport NexGen-Hybrid Bedienungsanleitung

Travis Industries

Travis Industries Arbor Bedienungsanleitung

Travis Industries

Travis Industries 1250 Wood Stove Bedienungsanleitung

Travis Industries

Travis Industries 1750 Bedienungsanleitung

Travis Industries

Travis Industries LOPI Liberty Bedienungsanleitung

Travis Industries

Travis Industries Avalon 1190 Bedienungsanleitung

Travis Industries

Travis Industries Leyden 250-00622 Bedienungsanleitung

Travis Industries

Travis Industries Endeavor NexGen-Hybrid Bedienungsanleitung

Travis Industries

Travis Industries 1750 Bedienungsanleitung

Travis Industries

Travis Industries Avalon Olympic Bedienungsanleitung

Travis Industries

Travis Industries Lopi Bedienungsanleitung

Beliebte Holzofen Handbücher anderer Marken

Plamen

Plamen ECO MINIMAL 50 Bedienungsanleitung

RAIS

RAIS 800 Bedienungsanleitung

Henley

Henley Arklow Bedienungsanleitung

Jøtul

Jøtul F 500 Bedienungsanleitung

Englander

Englander BLUE RIDGE 100 Bedienungsanleitung

WoodPro

WoodPro WS-TS-1500 Bedienungsanleitung

Contura

Contura C 586W Bedienungsanleitung

Nordpeis

Nordpeis N-20 T Bedienungsanleitung

Palazzetti

Palazzetti EVA Konfigurationshandbuch

Lopi

Lopi 1250 Republic Bedienungsanleitung

Panadero

Panadero CAPRI 3V Programmierhandbuch

RAIS

RAIS RONDO 92 Bedienungsanleitung

RAIS

RAIS attika NEXO 100 GAS Bedienungsanleitung

ADURO

ADURO 15-3 Benutzerhandbuch

Pacific energy

Pacific energy SUPER 27 SPECTRUM Bedienungsanleitung

Avalon

Avalon Olympic 11190 Bedienungsanleitung

Ventis

Ventis HES350 Bedienungsanleitung

IronStrike

IronStrike Striker S160GL Bedienungsanleitung