Traxxas PRO SCALE 6591 Bedienungsanleitung

Covers Part #6591

Pro Scale

Advanced Lighting Control System Installation Instructions

Kit Contents:

• Pro Scale Lighting Power Module

• Power module chassis mount

• Pro Scale Lighting Distribution Block

• Motor sense wire harness

• Breakaway cable (part of the distribution block)

• MAXX® Link cable (Data Link) (TQi Radio System only)

• Receiver communication cable

• 2.6x8mm button-head cap screw (2)

• 2.5x10mm countersunk cap screw (1)

• 2.5x12mm cap screw (1)

• 2.5x18mm cap screw (1)

• Zip ties (10)

• Silicone grease

TRAXXAS.com

Traxxas, 6250 Traxxas Way, McKinney, TX 75070,

Phone: 972-549-3000, Fax: 972-549-3011, e-mail: [email protected]

HKC20008-R02 Rev 201203

Letter Description Function

A Reverse light harness Back up light LEDs when vehicle is put in reverse

B Rear turn signal harness Rear turn signal LEDs (if equipped)

C Tail light harness Tail lights, brake lights, and rear integrated turn signal LEDs

(if equipped)

D Rear side marker harness Rear side marker LEDs (if equipped)

E Rear independent turn signal jumper

Install jumper when using rear independent turn signals

(separate amber LEDs); remove jumper when using rear

integrated turn signals (single red LED for tail, stop, and turn)

F Rear integrated turn signal jumper

Install jumper when using rear integrated turn signals (single

red LED for tail, stop, and turn). Remove jumper when using

rear independent turn signals (separate amber LEDs)

G Head light assembly harness Headlights, front marker light LEDs, and side marker light LEDs

H Front turn signal harness Front turn signal light LEDs

K Rear high brake light harness High brake light LEDs (if equipped)

M Light bar high/low harness LED light bar that typically mounts to the roof of the vehicle

(if equipped)

NRock lights/scene lights assembly

harness

Accessory LED lighting that mounts to the vehicle body

(if equipped)

Each TRX-4® and TRX-6™ model has its own unique LED light kit package (lights and wiring) and Pro Scale Lighting Installation Kit (listed below, each sold

separately). The included instructions cover installation of the mounting system and a wiring diagram specific to the model. If you have already installed a

Traxxas LED light kit on your TRX-4 or TRX-6 model, the installed lights are compatible with the Pro Scale Advanced Lighting Control System, except for

the Land Rover® Defender®, which requires a new LED light kit with additional lighting positions. Visit Traxxas.com/ProScaleLighting for additional information.

The Traxxas Pro Scale® Advanced Lighting Control System consists of two major electronic components: the Pro Scale Lighting Power Module (LPM)

and the Pro Scale Lighting Distribution Block (LDB). The LPM installs on the chassis of the vehicle and performs as the voltage regulator and power

supply for the lighting system. It also controls various lighting functions through the two buttons on the face of the module and communicates with

the receiver in the model via the communication cable (or the optional included MAXX® Link cable for models equipped with a TQi radio system). The

LDB mounts in the body of the vehicle and is the distribution hub for all the various wired lights in the body. Its main function is to direct power and

instructions to each of the installed lights to operate features such as brake lights, tail lights, reverse lights, turn signals, and high/low beam lighting.

There is only one rugged breakaway wiring connector between the LDB and the LPM for reliable lighting performance, plus it makes it easy to remove

the body for vehicle service. The connector is designed to break away from the vehicle, without damage, if the body comes off the vehicle in a crash.

There are lighting channels on the LPM which allow lighting installed on the chassis to be permanently connected and integrated into the system. This is

helpful to install features such as rock lights, bumper lights, and other chassis-mounted accessory lighting.

Tools required:

• 2.0mm hex wrench (part #3415, sold separately)

• Wire cutters (to trim zip ties)

• Small needle nose pliers

AUX

POWER

IN RX INOUT

Part 6592

MOTOR

SENSOR

MAXX LINK

SIGNAL

MODE

PRO SCALE® LIGHTING POWER MODULE

Mode Select

(see table in

Operation section)

Signal Select

(see table in

Operation section)

Breakaway Cable

Connector Port

(connects Power Module

to Distribution Block)

to Traxxas XL-5 HV Electronic

Speed Control (ESC) or direct

battery power source

up to 3s LiPo or 12.6V

Receiver Communication Cable Port

(connects power module to receiver

using receiver communication cable)

Motor Sense

Connector Port

Auxiliary Power Connector

(3V - always on)

POWER MODULE

Top View

Side Views

MAXX® Link Cable Ports

(connects power module to

receiver using MAXX Link cable)

(TQi Radio System only)

Visitez Traxxas.com/manuals pour télécharger

les instructions dans votre langue.

Visite la página Traxxas.com/manuals para

descargar el instrucciones en su idioma.

Auf Traxxas.com/manuals, können Sie

anleitung in Ihrer Sprache downloaden.

Model Fitment TRX-4 Sport TRX-4 Sport

Equipped with Traxx™

Mercedes-Benz®

G 500®

Mercedes-Benz®

G 63®

Land Rover®

Defender® Ford® Bronco® 1979 Chevrolet®

Blazer®

1969 & 1972 Chevrolet®

Blazer® Body

Vehicle

Model Number 82024-4 82034-4 82096-4 88096-4 82056-4 82046-4 82076-4 9111X

9112X

Installation Kit

Part Number* 8083** 8083** 8893** 8893** Included with 8095

LED Light Kit 8032** 8082** 8091

Compatible

LED Light Kit(s)

Part Number*

8085, 8086,

8087, 8088

LED Light Kit

factory installed 8899 LED Light Kit

factory installed 8095

†

8036 8039 8090

*All LED light kits and installation kits sold separately. Install LED lights kit(s) prior to installation of the Pro Scale Advanced Lighting Control System.

**Includes additional amber and/or reverse lights (as required by model).

†Includes additional amber, fog, and reverse lights. LED Light Kit 8030 for Land Rover® Defender® is not compatible with the Pro Scale Lighting Power Module.

PRO-SCALE

DISTRIBUTION

BLOCK

#XXXX

™

Part 6593

PRO SCALE® LIGHTING

DISTRIBUTION BLOCK

LED LIGHT HARNESS PORTS

Wiring connectors for the lights are labeled

with numbers and/or colors.

XL-5 HV ESC

Motor

Chassis Wiring

(Top Down View)

To Motor Connector

Receiver Communication Cable

To Motor Connector

To ESC

To Receiver

Motor Sense

Connectors

From ESC

From CH2

Lighting

Power

Module

To ESC

Lighting

Power

Module

FRONT

Receiver Communication Cable

Black Wires to CH2

Blue Wire to CH1

Receiver

Body Wiring

(Bottom Up View)

Side

Marker

Side

Marker

Part 6593

PRO SCALE® LIGHTING

DISTRIBUTION BLOCK

Reverse LightReverse Light

Tail Light / Turn Signal /

Brake Light

Tail Light / Turn Signal /

Brake Light

Jumper

Headlight /

Turn Signal

Headlight /

Turn Signal

To MAXX Link

IN port on

Lighting Power

Module

Route wires under

battery tray

Route wires under

battery tray

For more information about

connecting additional chassis

mounted accessories (such as light bars

mounted on bumpers), please visit the

Support page on Traxxas.com

For more information about

connecting additional chassis

mounted accessories (such as light bars

mounted on bumpers), please visit the

Support page on Traxxas.com

Rock

Light

Rock

Light

Rock

Light

Rock

Light

Rock

Light

Rock

Light

Rock

Light

Rock

Light

From ESC

Actual mounting view.

Distribution Block face shown

in the diagram for clarity.

Optional MAXX Link

Cable Wiring

(TQi Receiver Only)

Breakaway Cable from

Distribution Block mounted on body

Part 6593

PRO SCALE® LIGHTING

DISTRIBUTION BLOCK

Breakaway Cable

to Lighting Power

Module on chassis

WIRING DIAGRAM

Visit Traxxas.com/ProScaleLighting

for additional information about

installing and connecting accessories

such as auxiliary lighting (rock lights

shown, part #8026X, sold separately)

to the Pro Scale Lighting Module.

POWER MODULE INSTALLATION

Remove the 8028 LED lights power supply from the chassis (if installed). Install the

Power Module mount on the chassis with the included 2.5x10mm countersunk

cap screw; then, install the Lighting Power Module on the mount with the

included 2.5x12mm (1) and 2.5x18mm (1) cap screws (Fig.1).

COMMUNICATION CABLES

Your Pro Scale Advanced Lighting Control System

includes two communication cables: the Receiver

Communication Cable and the optional MAXX® Link

Cable. You can use the Receiver Communication

Cable with any TRX-4 or TRX-6 model. The MAXX

Link Cable is designed for use only with TRX-4 or

TRX-6 models equipped with the TQi receiver. The

6511 Traxxas Link Wireless Module (sold separately)

is required for Traxxas Link App functionality. Some

models may require a software update for the TQi

receiver via the Traxxas Link App for custom lighting

controls and configurations.

Only use one of the communication cables

to connect the Lighting Power Module to the

receiver. Do not use both cables together. MAXX®Link Cable

3. Remove the receiver box cover by removing the three 3x8mm button-head cap screws (Fig 5).

4. Remove the wire clamp by removing the two 2.5x8mm cap screws (Fig 5).

5. Feed the loose end of the Receiver Communication Cable connector over the wire guide and into

the receiver box. To make installation easier, unplug and remove a few of the existing wires from

the receiver box. Note the locations of any unplugged wires. Use needle nose pliers to help

grab the connectors and pull them through. Arrange all wires neatly between the wire guides in

the receiver box (Fig. 6). The excess wire will be bundled inside the receiver box.

6. Apply a bead of the included silicone grease

to the wire clamp (Fig. 7).

7. Reinstall the wire clamp and tighten the two

2.5x8mm cap screws securely (Fig. 8).

8. Unplug the electronic speed control (ESC)

from the receiver (channel 2).

9. Plug the communication cable into the

receiver (Fig. 9): the black connector with

the single blue wire plugs into one of the

channel 1 ports; the female black connector

with the 3 black wires plugs into the channel

2 port. Now, plug the black male connector

(white, red, black servo cable) from the ESC

into the black female connector (white, red,

black servo cable) on the communication

cable (refer to the Wiring Diagram for more

detail). Leave the steering servo cable

plugged into the other channel 1 port.

10. Make sure the blue o-ring gasket is properly

seated in the groove in the receiver box so

that the cover will not pinch it or damage it

in any way.

11. Reinstall the cover on the receiver box and tighten the three 3x8mm

button-head cap screws securely. Inspect the cover to make sure that the

O-ring seal is not visible.

12. Use the supplied zip ties to bundle the wires neatly and attach them to

the vehicle as needed so that loose wires will not become entangled with

moving parts.

2.5x18mm CS

2.5x10mm CCS

Power Module Mount

2.5x12mm BCS

3x8mm BCS

Receiver Box Cover

2.5x8mm CS

Wire Clamp

Fig. 1

Fig. 7 Fig. 8

TQ Receiver

Receiver Communication

Cable Black wires to CH2

Receiver Communication

Cable Blue wire to CH1

Servo wire to CH1

to ESC

Fig. 9

Fig. 3Fig. 3

ReceiverReceiver

Communication CableCommunication Cable

Wire GuideWire Guide

Fig. 6Fig. 6

Fig. 4Fig. 4

Battery Tray

3x10mm CCS

(hidden by battery hold down)

Receiver Communication

Cable

MOTOR SENSE WIRING HARNESS INSTALLATION

1. Unplug the red and black motor wires (bullet connectors) from

the ESC. Plug the bullet connectors from the motor and the

ESC into the motor sense wiring harness (red to red and black

to black) (Fig. 10). Plug the harness connector into the Motor

Sensor port on the power module (refer to the Wiring Diagram

for more detail).

2. Use the supplied zip ties to bundle the wires neatly and attach

them to the vehicle as needed so that loose wires will not

become entangled with moving parts.

3. Plug the breakaway cable from the distribution block into the

connector on top of the Power Module before installing the

vehicle body (Fig. 11). Motor Sense Connectors

Fig. 10Fig. 10

Breakaway Cable from

Distribution Block

Fig. 11Fig. 11

1. Plug one end of the Receiver Communication Cable

(Fig. 2) into the RX IN port on the Power Module (Fig. 3)

(refer to the Wiring Diagram for more detail).

2. Remove the 3x10mm counter-sunk cap screws (2) from

the battery tray (Fig. 4). Lift up the battery tray and route

the Receiver Communication Cable from the Power

Module under the battery tray and to the receiver box

(refer to the Wiring Diagram for more detail). Use a zip tie

(included) to attach the wires. Reinstall and tighten the

battery tray screws. Note: Be careful not to pinch or

damage any of the wires under the battery tray.

RECEIVER COMMUNICATION CABLE INSTALLATION

Fig. 2

Fig. 5

Download and install the latest rmware updates, change the module

settings, and gain access to additional functions using the Traxxas Link App

(available in the Apple App StoreSM or on Google Play™).

The TQi transmitter with the Traxxas Link Wireless Module

(part #6511, sold separately) are required.

Warranty Information

Traxxas electronic components are warranted to be free from defects

in materials and workmanship for a period of 30 days from the date of

purchase.

Limitations: Any and all warranty coverage does not cover replacement

of parts and components damaged by abuse, neglect, improper or

unreasonable use, crash damage, water or excessive moisture, chemical

damage, improper or infrequent maintenance, accident, unauthorized

alteration or modification or items that are considered consumable.

Traxxas will not pay for the cost of shipping or transportation of a defective

component to us.

Traxxas Lifetime Electronics Warranty

After the expiration date of the warranty period, Traxxas will repair

electronic components for a flat rate. Please visit Traxxas.com/support

for a current schedule of warranty costs and fees. The covered repairs are

limited to non-mechanical components that have NOT been subjected

to abuse, misuse, or neglect. Products damaged by intentional abuse,

misuse, or neglect may be subject to additional charges. Traxxas liability,

in no case, shall be greater than the actual purchase price of this product.

For replacement, product must be returned in brand new condition, with

packaging and itemized sales receipt.

This device complies with FCC Part 15 & IC RSS-210 rules

subject to the following conditions: 1) This device may

not cause harmful interference, and 2) This device must

accept all interference received, including interference

that may cause undesired operation.

For patent and patent-pending information, please visit Traxxas.com/pat

TRAXXAS.com

Traxxas, 6250 Traxxas Way, McKinney, TX 75070,

Phone: 972-549-3000, Fax: 972-549-3011, e-mail: [email protected]

Headlights Mode Selection

Use the Mode button on the Pro Scale

Lighting Power Module to cycle through

the different lighting modes (from Low

Beam Mode to High Beam Mode to

Daytime Mode).

Hazard Lights

Use the Signal button on the Pro Scale

Lighting Power Module to turn the hazard

lights on or off.

Turn Signals

The turn signals are activated by default. To

deactivate the turn signals, press and release

the Signal button on the Pro Scale Lighting Power Module two times quickly. Both left turn signal LEDs will blink once, and then both right turn signals LEDs

will blink once to indicate that the turn signals are deactivated.

To reactivate the turn signals: Press and release the Signal button two times again quickly. Both left turn signal LEDs will blink twice, and then both right

turn signals LEDs will blink twice to indicate that the turn signals are activated.

Turn Signal Operation:

With the vehicle stopped, turn the steering wheel on the transmitter (left or right) to turn on the LEDs. The turn signal LEDs will continue to flash while the

steering wheel is turned in this same direction or remains centered. Turn the steering wheel in the opposite direction to cancel the turn signal.

AUX

POWER

IN RX INOUT

Part 6592

MOTOR

SENSOR

MAXX LINK

SIGNAL

MODE

PRO SCALE

LIGHTING POWER MODULE

OPERATION

WARRANTY

6V 50mA

CH1

CH2

Important: To prevent possible damage to the electronics

while using an external BEC, do not connect both the MAXX

Link Cable and Receiver Communication Cable to the Lighting

Power Module at the same time.

Lighting Power Module

ESC

Receiver

BEC Receiver

Communication

Cable

Signal

Selection Action

Hazard Lights On Press and release Signal once

Hazard Lights O Press and release Signal once again

Deactivate Turn Signals Press and release Signal 2x quickly

Activate Turn Signals Press and release Signal 2x quickly again

Mode

Selection Action

Low Beam Headlights Default

High Beam Headlights Press and release Mode

Daytime Headlights (o) Press and release Mode once again

App Store is a service mark of Apple Inc. Google Play is a trademark of Google Inc.

Mercedes-Benz®, G 500®, and G 63® are trademarks of Mercedes-Benz/Daimler AG.

Land Rover® and Defender® are trademarks of Jaguar Land Rover Limited.

Ford® and Bronco® are trademarks of Ford Motor Company.

Chevrolet® and Blazer® are trademarks of General Motors.

All copyrights and trademarks are used by Traxxas under license.

OPTIONAL MAXX LINK CABLE WIRING

Use the optional included MAXX®Link Cable

with any Traxxas TRX-4 and TRX-6 model that

includes a TQi radio system to connect the

Lighting Power Module to the receiver.

The MAXX Link Cable is designed to work

with the Traxxas Link™Wireless Module

(part #6511, sold separately) to provide

Traxxas Link App functionality for custom

lighting controls and configurations.

Some models may require a software update

for the TQi receiver via the Traxxas Link App

(Traxxas Link Wireless Module required).

Plug the MAXX Link cable into the MAXX Link

IN port on the Lighting Power Module. Use the

same wire routing from the Lighting Power

Module and into the receiver box as shown in

the Receiver Communication Cable Installation

instructions. Plug the loose end of the cable

into the expansion port on the receiver.

Traxxas Link Wireless Module

(part #6511, sold separately)

WIRING DIAGRAM WITH HIGH-OUTPUT EXTERNAL BEC

(part #2262, sold separately)

TQi Receiver

MAXX Link Cable

to Expansion Port

Servo wire to CH1

ESC wire to CH2

Pro Scale Lighting

Power Module

Andere Traxxas Steuerungssystem Handbücher

Traxxas

Traxxas BXL-1 Bedienungsanleitung

Beliebte Steuerungssystem Handbücher anderer Marken

Pentair Pool Products

Pentair Pool Products Compool Bedienungsanleitung

ComfortNET

ComfortNET CTK04 Bedienungsanleitung

Fireye

Fireye InSight II 95DSS3 Bedienungsanleitung

CAME

CAME G3000 Bedienungsanleitung

Idemia

Idemia MorphoAccess VP MD Bedienungsanleitung

Axis

Axis P1445-LE-3 Bedienungsanleitung

HEIDENHAIN

HEIDENHAIN TNC 150 B Bedienungsanleitung

CNC-Step

CNC-Step High-Z T-Series Bedienungsanleitung

Doosan

Doosan DVF Series Bedienungsanleitung

Honeywell

Honeywell KAP 140 Bedienungsanleitung

Honeywell

Honeywell vk41 series Bedienungsanleitung

AirBench

AirBench FPW Installationsanleitung

Cypress

Cypress HHR-3160 Bedienungsanleitung

CAME

CAME GLT40AOS Bedienungsanleitung

Zonex

Zonex GEN II -VVT Benutzerhandbuch

Altronics

Altronics K 9650 Bedienungsanleitung

micro-trak

micro-trak RoadMaster Bedienungsanleitung

micro-trak

micro-trak Calc-An-Acre II Bedienungsanleitung