TRENDnet TEG-S811Fi Bedienungsanleitung
H/W: v1.0R
TEG-S811Fi
Quick Installation Guide
Table of Contents
English ......................................................................................................
Troubleshooting ........................................................................................
1
1
4
2
5
1. Before You Start
2. Hardware Installation ........................................................................
3. Configure the Switch .........................................................................
................................................................................
Table of Contents
Version 01.21.2008
System Requirements
Application
Package Contents
1. Before You Start
English
1
?
?User Guide CD-ROM
?Quick Installation Guide
?2 Mounting Brackets with Screws
?RS-232 cable
?AC Power Cord
TEG-S811Fi
?
?Computer with Serial port
?50/125 or 62.5/125 µm Multimode Fiber cable with SC-type connectors
for 100BaseFX ports
?Mini-GBIC module (e.g. TEG-MGBSX, TEG-MGBS10, TEG-MGBS40,
TEG-MGBS80, TEG-MGBS10D3_D5, TEG-MGBS40D3_D5) for Mini-
GBIC slots (optional)
Web Browser: Internet Explorer (6.0 or above)
1000MbpsFiber 10/100Mbps
8-Port 10/100Mbps Layer 2 Managed Switch
with Gigabit Port and Mini-GBIC Slot
(TEG-S811Fi)
24-port Gigabit Web Smart Switch
with Mini-GBIC slots
(TEG-240WS)
Multi-Mode Fiber
Mini-GBIC Modules
(TEG-MGBSX)
RS-232
Laptop with PC Card
(TE100-PCBUSR)
Workstation with PCI Adapter
(TE100-PCIWA)
Workstation
8-Port 100Base-FX Layer 2
Managed Switch with Mini GBIC Slot
(TEG-S081FMi)
2. Hardware Installation
English
2
Note: After hardware installation is complete, use your browser to configure the
TEG-S811Fi. See Section 3 Configure your Switch for more information.
1. Connect the Power Cord to the
rear of the TEG-S811Fi and then
to a power outlet.
English
3
4. Slide a TRENDnet mini-
GBIC module into the mini-
GBIC slot (optional).
2. Connect a RJ-45 Ethernet cable
from one of the 8-ports on the
switch to an Ethernet connection
on your network.
Register Your Product
To ensure the highest level of customer service and support, please take a moment to
register your product Online at: www.trendnet.com/register
Thank you for choosing TRENDnet
4. Slide a TRENDnet mini-
GBIC module into the mini-
GBIC slot (optional).
2. Connect a RJ-45 Ethernet cable
from one of the 8-ports on the
switch to an Ethernet connection
on your network.
3. Connect a RJ-45 Cat 5e
Ethernet cable to an
10/100/1000BaseT connection
on your network (optional)
Register Your Product
To ensure the highest level of customer service and support, please take a moment to
register your product Online at: www.trendnet.com/register
Thank you for choosing TRENDnet
English
4
Note: Before the Switch can be configured, a Static IP address must be
assigned on your computer's network adapter in the subnet of 192.168.16.x.
Since the Switch's default IP address is 192.168.16.1, make sure no other
network devices are assigned an IP address of 192.168.16.1. (Refer to
Troubleshooting section on how to configure TCP/IP settings on your PC.)
3. Configure the Switch
Browser Configuration
3. Click System > IP Configuration.
Then change the IP Address to be
in the same subnet as your
Network. Enter the Subnet Mask
and Gateway to match your
network. Then click Apply.
1. Open your web browser, type
http://192.168.16.1 in the Address
bar, and then press Enter.
2. Enter the User name and
Password, and then click OK.
By default:
User Name: root
Password: root
5
Troubleshooting
Q1:
A1:
After connecting the TEG-S811Fi to a power outlet, the LEDs do not turn on.
Check the connection of the power cord to the TEG-S811Fi and the power outlet. Also
check that the power outlet is receiving power.
Q3:
A3:
I connect the switch to my network via the mini-GBIC module, but I am unable to make a
connection.
First, verify that you are using the proper fiber cable. Second, verify that the TX and RX
cables have been reverse on the opposite Fiber connection. Third, when connecting to the
mini-GBIC modules, your Fiber connection must be Gigabit. Fourth, power down the switch.
Wait 15 seconds, then plug the switch back in.
Q4:
A4:
How do I login to the switch via the console port?
Follow the instructions below:
1) Connect the RS-232 cable from a serial port on your Windows PC to the console port on
your computer.
2) Go to Start -> Programs -> Accessories -> Communications -> Hyperterminal
3) Enter a name, select an icon and then click OK.
4) Select the correct COM port (e.g. COM1, COM2) and then click OK.
5) Enter the following, click Apply and then click OK:
Bits per second: 9600
Data bits: 8
Parity: None
Stop bits: 1
Flow control: None
6) Press Enter.
7) Enter the user name and password. By default, the user name and password is root.
Please refer to the User's Guide for a list of commands.
If you still encounter problems or have any questions regarding the TEG-S811Fi, please contact
TRENDnet’s Technical Support Department.
Q2: How do I configure TCP/IP settings on my computer?
1. Go into the Control Panel and double-clic the Network
Connections icon, right-click the Local Area
Connection icon and then click Properties.
2. Click Internet Protocol (TCP/IP) and then click
Properties. Then click on Use the following IP
address, and make sure you assign your network
adapter an IP address in the subnet of 192.168.16.x.
Certifications
This equipment has been tested and found to comply with FCC and CE Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received. Including interference that may
cause undesired operation.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV
INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS
EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO
OPERATE THE EQUIPMENT.
Waste electrical and electronic products must not
be disposed of with household waste. Please
recycle where facilities exist. Check with you Local
Authority or Retailer for recycling advice.
ADVERTENCIA
En todos nuestros equipos se mencionan claramente las caracteristicas del adaptador de
alimentacón necesario para su funcionamiento. El uso de un adaptador distinto al
mencionado puede producir daños fisicos y/o daños al equipo conectado. El adaptador
de alimentación debe operar con voltaje y frecuencia de la energia electrica domiciliaria
existente en el pais o zona de instalación.
Copyright ©2008. All Rights Reserved. TRENDnet.
20675 Manhattan Place
Torrance, CA 90501
USA
Product Warranty Registration
Please take a moment to register your product online.
Go to TRENDnet’s website at http://www.trendnet.com/register
Customer Support
Email:
Europe (Germany France Italy Spain Switzerland UK)
English/Espanol - 24/7
Francais/Deutsch - 11am-8pm, Monday - Friday MET
English/Espanol - 24/7
Francais/Deutsch - 11am-8pm, Monday - Friday MET
Worldwide
Telephone: +(31) (0) 20 504 05 35
Toll Free Telephone: +00800 60 76 76 67
. . . . .
Visit www.trendnet.com/support
Andere Handbücher für TEG-S811Fi
2
Inhaltsverzeichnis
Andere TRENDnet Schalten Handbücher
TRENDnet
TRENDnet TEG-S80TXE - Copper Gigabit Switch Bedienungsanleitung
TRENDnet
TRENDnet TEG-S50G Bedienungsanleitung
TRENDnet
TRENDnet TEG-S16Dg Bedienungsanleitung
TRENDnet
TRENDnet TE100-S24V Bedienungsanleitung
TRENDnet
TRENDnet TE100-SK2 Bedienungsanleitung
TRENDnet
TRENDnet TE100-DS24 Bedienungsanleitung
TRENDnet
TRENDnet TK-423K - USB/PS/2 KVM Switch Bedienungsanleitung
TRENDnet
TRENDnet TK-209i Bedienungsanleitung
TRENDnet
TRENDnet TE100-S810Fi - Switch Bedienungsanleitung
TRENDnet
TRENDnet TEG-S2400I - DATA SHEETS Bedienungsanleitung
TRENDnet
TRENDnet TK-217i Bedienungsanleitung
TRENDnet
TRENDnet TI-PG541i Bedienungsanleitung
TRENDnet
TRENDnet TK-205i Bedienungsanleitung
TRENDnet
TRENDnet TE100-S50g Bedienungsanleitung
TRENDnet
TRENDnet TPE-S44 - Switch Bedienungsanleitung
TRENDnet
TRENDnet TEG-40128 Bedienungsanleitung
TRENDnet
TRENDnet TE100-S50g Bedienungsanleitung
TRENDnet
TRENDnet TE-800plus Bedienungsanleitung
TRENDnet
TRENDnet TEG-S4M8TX Bedienungsanleitung
TRENDnet
TRENDnet TEG-082WS Bedienungsanleitung
