tri-art audio ta 0.5 Bedienungsanleitung
ta 0.5
turntable
S-Series
User Manual
Product #18395
*Read the user manual
before operating.
safety
information
Before you start...
Warning of a hazard for the user, the unit or possible misuse. Important notice.
Thank you for buying a Tri-Art Audio product. Please read through this manual to
understand and operate this product correctly. Please keep this manual in a safe place so
that you may refer to it whenever necessary. Please ensure the product you are using is
rated for your country’s electrical system, or it will not be covered under our warranty.
Warning:
To prevent re or shock hazard, do not expose this product to rain or moisture.
Important Notice:
The serial number for this equipment is located on the bottom of this component. Please
write this serial number on the enclosed warranty card and follow the instructions to register
your product for our three (3) year limited warranty.
This equipment is designed for consumer use, such as home audio systems. It is not
designed to operate in a business environment or a mobile application. Mobile, pro or
commercial businesses such as restaurants will not be covered under warranty.
Caution:
To reduce the risk of electric shock, do not remove cover (or back). No user serviceable
parts inside. Refer servicing to qualied service personnel.
safety
information
Safety Instructions
Read Instructions:
All the safety and operating instructions should be read before operating this equipment.
Retain Instructions:
The safety and operating instructions should be retained for future reference.
Heed All Warnings:
All warnings, set up procedures, and operating instructions should be strictly adhered to.
Follow all instructions carefully.
Water and Moisture:
Under no circumstances should this audio component be used near water.
It is not to be used in a bathroom, water closet, shower, kitchen, wet basement,
pool/spa/sauna area, or outside.
safety
information
Safety Instructions
Ventilation:
Please ensure that the location of this equipment is such that in no way does it prevent adequate
ventilation. Do not enclose this in fabric or enclose in a cabinet where there is no adequate
ventilation. In no instance should the product be located where the ow of air is impeded or cannot
allow proper ventilation.
Heat:
This product should be located well away from all the heat sources such as but not limited to
heaters, forced air heat, radiators, stoves, and replaces.
Power Sources:
The Tri-Art component should be connected to a power supply as listed on the actual component
and manual.
Cleaning:
Your Tri-Art product was soaked in hemp oil and sealed in beeswax. Only use the Tri-Art Beeswax
and Hemp Oil in moderate amounts as per the instructions to freshen up the appearance from time
to time as needed. Do not use lacquers or aerosol wax products with this product. Do not pour
water on the surface at any time.
Heavy Objects:
Do not place heavy objects on this component.
turntable front
1
16
27
38
4
5
2
6
7
8
3
4
5
Spindle
Platter
Plinth
Power Switch
Iso Feet with Sorbothane
Azimuth Adjustment Basket
Arm Clamp
Cartridge Mount
turntable back
2
1
7
6
5
3
4
1 6
2 7
3
4
5
Arm Base
Left and Right Output
Plinth
Power Switch
Sub Platter
Belt
Pulley
*Located under the Platter
turntable specs
Table Details:
Plinth: 3 Ply Bamboo laminate 19.05mm (3/4″)
Motor: Single 24 Pole Synchronous AC Motor
Pulley: Brass Pulley
Speed: 33.3 & 45 rpm
Drive: Belt Drive
Platter: 3-ply Bamboo Laminate 19.05mm (3/4″)
Sub Platter: Aluminum Sub Platter with Steel Shaft
Legs: Leveling Legs
Bearing: Bronze Collar Bearing with ABEC7 Carbonized Ceramic Ball Bearing
Dimensions: H 15.5cm x W 40.9cm x L 33.3cm / 8 1/4″ x 16″ x 32.39″
Arm Details:
Material: Three Ply Bamboo Laminate 12mm
Settings: VTA & Azimuth Adjustments
Anti-Skate Adjust: Passive Anti-Skate
Bearing Assembly: Bronze with Brass Collar Spike and Synthetic,
High Viscosity Grease Bearing
Arm Base: Bamboo Supports on Plinth
Wiring: Cardas Wire 33 AWG Uninterrupted from Headshell Clips to Brass
Female RCA with Silver Plated Cartridge Clips
Level: Micro Bubble Level Included
Arm Length: 9” / 222 mm
Tone Arm Mass: 10g
Crafted with bamboo and natural sheep’s wool.
Learn more at triartaudio.com
Power Switch:
The power switch is located on the far-left front of the turntable. It should be in the off
position as shown during set up. Please do not rapidly turn on and off the power switch.
The switch is connected to a safety circuit to ensure correct performance. The rapid cycling
of the switch bypasses the protection circuitry and is not recommended.
Power Cord:
Locate the power cord and plug the female connector to the male connector located under
the plinth. Plug the male side from the supplied cord into your wall electrical socket. For
best results please ensure you have the correct polarity with ground from your wall electrical
receptacle and ensure that the turntable cable is correctly installed.
NOTE: Incorrect polarity may result in the platter turning counter-clockwise or
humming of the motor(s).
The male side of the power cord must be plugged into an outlet with the
cord facing downwards.
use &
guidelines
Above
Off Position Off Position
Side
underneath the plinth
Ground
Front view Side view
Install the Belt:
Locate the rubber belt and install it around the sub platter rst and then around the pulley.
The upper position of the pulley is for 33 rpm and the lower one is for 45 rpm.
Turn the power switch on and ensure that the
pulley turns smoothly. Turn the turntable off
before moving on to the next step.
The platter is not installed on your TA-0.5 it is
packaged separately within your box. Locate
the platter and gently install it over the spindle.
use &
guidelines
Sub Platter
33 rpm
Pulley
45 rpm
Locate the removable spindle cover and insert it over the spindle on the table.
The spindle cover is removable to further isolate the record and the Platter from
external vibrations.
Install the Interconnects:
Ensuring you have muted or turned off your sound system, locate the Interconnects (or use
your own interconnects) and connect them to the turntable ensuring the direction arrow for
the cables is owing away from the turntable. Then connect the turntable interconnects into
the input of your phono/pre-amplier ensuring you match the R and L inputs/outputs.
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere tri-art audio Drehscheibe Handbücher
