Tri-M Systems FlexCom104-GPS Bedienungsanleitung

FlexCom104-GPS Manual

Flexible Communications

PC/104 Platform

With GPS

Manufactured by:

Tri-M Technologies

Technical Manual

Revision: 2014-09-22

[email protected] Toll-free (Canada & USA) 1-800-665-5600

Direct +1-604-814-5069

P EFACE

This manual is for integrators of applications of embedded systems. It contains information on hardware

requirements and interconnection to other embedded electronics.

DISCLAIME

Tri-M Technologies makes no representations or warranties with respect to the contents of this manual, and

specifically disclaims any implied warranties of merchantability or fitness for any particular purpose. Tri-M

Technologies shall under no circumstances be liable for incidental or consequential damages or related expenses

resulting from the use of this product, even if it has been notified of the possibility of such damages. Tri-M

Technologies reserves the right to revise this publication from time to time without obligation to notify any person of

such revisions. If errors are found, please contact Tri-M Technologies at the address listed on the title page of this

document.

o part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into

any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical,

chemical, manual, or otherwise, without the express written permission of Tri-M Technologies.

[email protected] Toll-free (Canada & USA) 1-800-665-5600

Direct +1-604-814-5069

CHAPTE 1 INT ODUCTION .......................................................................................................................... 4

GENERAL DE CRIPTION......................................................................................................................................................................4

FEATURE ......................................................................................................................................................................................4

PECIFICATION ...............................................................................................................................................................................5

CHAPTE 2 CONFIGU ATION ........................................................................................................................ 6

2.1 INTRODUCTION...........................................................................................................................................................................6

2.2 OFTWARE CONFIGURATION..........................................................................................................................................................6

2.3 IRQ INTERRUPT CONFIGURATION...................................................................................................................................................6

2.4 ERIAL PORT I/O ADDRE CONFIGURATION ...................................................................................................................................7

2.5 POWER OURCE........................................................................................................................................................................7

2.6 IN ERTING THE MODULE...............................................................................................................................................................7

2.7 ECURING THE MODULE...............................................................................................................................................................7

2.8 CONNECTING AN FV-4H GP .....................................................................................................................................................8

2.9 CONNECTING AN EXTERNAL ERIAL PORT........................................................................................................................................8

[email protected] Toll-free (Canada & USA) 1-800-665-5600

Direct +1-604-814-5069

Chapter 1 INT ODUCTION

General Description

The FlexCom104-GP has the following restrictions:

•Both Universal ocket modules supplied with 5V. No support for 3.3V socket modules

•Only Multitech Universal ocket wireless modules supported.

The FlexCom104-GPS is a communications platform capable of supporting two of the Multitech

Universal Socket compatible devices. Embedded in the FlexCom104-GPS is a quad UART

(ST16C554DIQ64) to provide communications to the two Universal Sockets, a mounting point for the

FV-4H GPS and an additional serial port. The ST16C554DIQ64 is an enhanced quad UART with 16

byte FIFOs on both transmit and receive.

The PC/104 bus provides access to quad UARTs. One UART port is connected to the auxiliary serial port.

The FlexCom104-GP supports wireless Multitech modules, with mounting holes.

In this document, the term “serial port” refers to a UART based communications port that is available on pin headers.

Features

•Two Multitech compatible Universal Sockets

•One RS-232 serial port on a 2x5 pin 2mm header with a MAX3250 ±50V isolated interface

•One mounting location for an FV-4H GPS

•PC/104 interface to high speed quad UART

•Selectable I/O address & IRQ

•Supports 5V Multitech modules

•GPS 1 Pulse per Second LED

•GPS 1 Pulse Per Second line fed to Carrier Detect line for time synchronization as per the standard PPSKit

configuration

[email protected] Toll-free (Canada & USA) 1-800-665-5600

Direct +1-604-814-5069

Specifications

Module specifications

Model FlexCom104-GP

upplied oscillator frequency 14.7456MHz

Universal ockets 2

R 232 erial ports 1

ize, PC/104 form factor compliant* 3.55”W x 3.75”L x 0.6”H

*Height measured without Universal Socket module installed.

*Some Universal Socket modules may be large enough to violate the PC/104 form factor.

UA T specifications

Model T16C554DIQ64

FIFOs 16 bytes

Ports 4

Serial port specifications

Protocol R -232

Duplex R -232 Full

Figure 1: FlexCom104-GP Dimensions

[email protected] Toll-free (Canada & USA) 1-800-665-5600

Direct +1-604-814-5069

3.775”

3.55”

Chapter 2 CONFIGU ATION

2.1 Introduction

Chapter 2 describes the software and hardware configuration required to properly integrate the FlexCom104-GP

into a PC/104 tack

The FlexCom104-GPS has configuration jumpers for I/O address, IRQ, mode of operation, and module

voltage.

2.2 Software Configuration

A utility is available from the Tri-M website (www.tri-m.com) to configure the FlexCom104-GPS under

Windows. Under Linux, setserial can be used to configure the FlexCom104-GPS.

The following command would configure the Linux kernel to use Module 1 as /dev/ttyS2 correctly with

the default settings.

setserial /dev/ttyS2 port 0x100 irq 7 uart 16850 baud_base 921600 spd_vhi

2.3 IRQ Interrupt Configuration

The FlexCom104-GP can be configured for IRQ5, IRQ7, IRQ10, IRQ11 and IRQ12 by the installation of jumper

shunts on JP1 as per Table 1.

PC/104 I Q Signal

Jumper JP1

Position Shunts

3 2 1 0

I Q7 *

Reserved

Yes

Reserved

Yes

Reserved

Yes

Reserved

Yes

Reserved

Yes

I Q12

Yes

I Q11

Yes

I Q10

Yes

Reserved

Yes

I Q7

Yes

Reserved

Yes

I Q5

Yes

Reserved

Yes

Reserved

Yes

Reserved

Yes

Where “Yes” = shunt installed, “No” = shunt not installed

oNo jumper shunt installed default is IRQ7.

[email protected] Toll-free (Canada & USA) 1-800-665-5600

Direct +1-604-814-5069

JP1 Jumper

Shunts

7-4 3-0

2.4 Serial ort I/O Address Configuration

The FlexCom104-GP I/O address can be configured by the installation of jumper shunts on JP1 as per Table 2.

Table 1: Serial Port I/O Address Configuration

erial Port I/O Addresses - Hex Jumper JP1

Position hunts

ocket

Modem# 1

ocket

Modem# 2

On-board GP

Module

External R 232

erial Port – CN4

7 6 5 4

100 108 110 118

180 188 190 198

Yes

1C0 1C8 1D0 1D8

Yes

200 208 210 218

Yes

240 248 250 258

Yes

280 288 290 298

Yes

300 308 310 318

Yes

380 388 390 398

Yes

Reserved

Yes

Where “Yes” = shunt installed, “No” = shunt not installed, and “xx” = don’t care.

oNo jumper shunt installed default is base addresses 100, 108, 110 & 118

2.5 ower Source

Universal ocket modules are available in 3.3V and 5V models. The FlexCom104-GP supports only 5V modules.

The 5V power for the FlexCom104-GP must be supplied over the PC/104 bus.

2.6 Inserting the Module

There are two Universal ocket module locations (Module1 and Module2) and modules will only fit in the

FlexCom104-GP in one orientation. Attempting to insert the module in any other orientation may damage the

module or the FlexCom104-GP .

Insert a module by placing the largest group of pins in their sockets at once, then align the rest of the pins, and apply

pressure evenly to the module until it settles in the socket.

The antenna cable will need to be routed from the Wireless Modem module to the outside of the enclosure for the

antenna to get a good signal.

2.7 Securing the Module

Wireless modules use two mounting screws to hold them into the socket. Two 4-40 1/8” countersunk

screws can be used with 0.312” female standoffs to secure the module.

[email protected] Toll-free (Canada & USA) 1-800-665-5600

Direct +1-604-814-5069

2.8 Connecting an FV-4H G S

A GP antenna must be connected to the MA connector on the FlexCom104-GP for the FV-4H GP to operate.

2.9 Connecting an External Serial ort

The serial port has the same pin out (see Table 3.6.1) as a standard IDC serial connector, however it

has 2mm pin spacing.

Table 2: External Serial Port Pin Out

Pin number Pin Function

1 CD

2 DSR

3 RXD

4 RTS

5 TXD

6 CTS

7 DTR

8 RI

9 GND

10 NC

The external serial has an on-board level converter for speeds up to 250kbps and has built-in E D protection.

[email protected] Toll-free (Canada & USA) 1-800-665-5600

Direct +1-604-814-5069

GPS SMA Antenna

Module1

Position

Module2

Position

CN4 Pin Out

Inhaltsverzeichnis

Andere Tri-M Systems Relais Handbücher

Tri-M Systems

Tri-M Systems TCB1000 Series Bedienungsanleitung

Tri-M Systems

Tri-M Systems IR104-V4 Bedienungsanleitung

Tri-M Systems

Tri-M Systems TCB1000 Series Bedienungsanleitung

Beliebte Relais Handbücher anderer Marken

Shelly

Shelly Pro Series Bedienungsanleitung

GE MVAX 11 Bedienungsanleitung

ABB

ABB RELION REF615R Bedienungsanleitung

Pilz

Pilz PNOZ X10 Betriebsanleitung

ABB

ABB SPAJ 142 C Stücklistenhandbuch

Kemo Electronic

Kemo Electronic B197 Bedienungsanleitung

Seg

Seg MRM3 Bedienungsanleitung

Basler

Basler BE1-700C Bedienungsanleitung

CD Automation

CD Automation REVEX 2PH 280A Bedienungsanleitung

Ruelco

Ruelco 1S04 Bedienungsanleitung

Basler

Basler V3E Z1P B2C1F Bedienungsanleitung

Doepke

Doepke Dupline DSM 2 Bedienungsanleitung

Siemens

Siemens SIRIUS 3RT1966-4D Bedienungsanleitung

GE DGP Bedienungsanleitung

Kyongbo Electronics

Kyongbo Electronics GDR-D01 Bedienungsanleitung

Siemens

Siemens SIPROTEC 4 Bedienungsanleitung

Siemens

Siemens BD2-AK03X/FS Series Bedienungsanleitung

Leuze

Leuze MSI-SR5B Bedienungsanleitung