Trilogy 993 Bedienungsanleitung
993
USER MANUAL
1
thank you
Welcome
Firstly, thank you for purchasing your Trilogy Audio Systems 993 Power Amplier, we value your custom.
We strive to design and build world class products that stand the test of time. By reading this manual you
can gain a clear understanding of the 993’s operation and learn to care for it correctly. In turn, it will reward
you with a lifetime of outstanding performance.
......................................
Nic Poulson.
CEO Trilogy Audio Systems.
www.trilogyaudio.com
2
3
Getting Started
5 Introduction
5 About this manual
7 Unpacking
7 Environment
7 Power Supply
9 Connections
11 Operation Guide
13 Operational Warnings
15 Operational Warnings
15 Protective Lockout Modes
17 TAS link Overview
19 TAS link Pinout
Care & Service
21 Cleaning
21 Servicing
21 Declarations
Glossary
22 Glossary
Specications/Returns
23 993 Specications
23 Returns
Acknowledgements
24 Acknowledgments
contents
4
5
Introduction
We prefer that your Trilogy dealer delivers, installs, sets up and explains your 993’s operation to you. However, we still
recommend that you read through this manual thoroughly and keep it to hand for reference.
Should any part of this manual or the operation of the 993 not be clear to you, please do not hesitate to contact your
Trilogy dealer. If they are not available please contact ourselves directly.
About this manual
Throughout this user manual, the following icons are used:
[power] This refers to a physical control or indicator on the 993.
LEFT OUTPUT This refers to a physical connection on the 993.
From this point on, any information presented on the left hand pages are pictorial representations of either the front or back
views of the 993 or other diagrams. Therefore consider the left hand pages as additional information to accompany the
written descriptions on the opposite pages.
6
7
Unpacking
Be careful when unpacking your Trilogy amplier, it is heavy: 19kg. Seek assistance if necessary. Store the packaging safely
for future use. It is the ideal method of protecting your amplier from damage during transport.
Environment
Do not site the amplier near liquids, or place water-lled containers near the unit. If water does come into contact with the
unit there is serious potential for an electric shock or re hazard. Immediately pull out the mains plug from the wall socket.
Contact your dealer to arrange an inspection before further use.
The amplier is cooled by convection and so needs good circulation of room temperature air under and around it. Do not
place it near sources of heat such as radiators or in direct sunlight. Do not enclose in a cupboard. Do not place directly on
carpet.
A at, smooth surface is required. As with all high resolution audio equipment, your amplier is sensitive to vibration, strong
magnetic elds and radio interference. A dedicated high performance equipment platform sited away from other appliances
is the optimum location.
Power Supply
The AC input voltage has been set for the country where it was purchased. Check that the label on the rear panel matches
your AC supply voltage before connecting the supply. The provided AC inlet cable should be used.
The 993 must be earthed through the IEC inlet connector. Do not disconnect the AC earth at any time. If in doubt about any
aspect of power supply, consult your Trilogy dealer or a qualied electrician.
To realise your amplier’s full potential we recommend high quality mains conditioning. See www.Isol-8.co.uk for more on
power supply and system solutions from our highly acclaimed sister company. If you are not using a mains conditioner for
best performance, make a direct connection to a mains outlet. Avoid using adapters where possible.
The input mains fuse is housed in a rear panel fuseholder. This is a 20mm ceramic type, full specication on page 23, which
the user can replace if required. Good quality power supplies, such as that in the 993, often have relatively high inrush
current when rst powered. Note this is when the 993 is turned on from standby, not when it is connected to the mains.
Depending on the exact position of the incoming mains sinusoidal waveform this can rarely blow the fuse or age the fuse
and lower its rated capacity for subsequent use. This is not unusual, it is similar to traditional light bulbs blowing usually when
rst turned on. It would therefore not be unknown to replace the fuse occasionally. However, if a replacement fuse blows
again immediately then there may be a serious fault. The unit should be unplugged from the mains, then please contact your
Trilogy dealer.
8
9
Connections
It is good practice to complete all interconnections before switching on to avoid any damage to your system’s loudspeakers.
Do not make connections or disconnections while the amplier is powered.
Connect with the supplied power input cable. The 993 can be left connected at all times to ensure reliable operation. If not
being used for extended periods of time, switch off at the mains outlet or at the rear panel power switch.
The amplier has single ended inputs on RCA “Phono” connectors.
The output is via copper terminals for connection to your loudspeakers. It is important to connect the speaker cables
correctly. Connect the red terminal (+) to the positive terminal of your loudspeaker, and the black (-) to the negative. Take
note of left and right and make sure that each connection is secure and the cable terminals are not touching another. Do not
over tighten the terminals as damage may result. Finger tight is sufcient torque.
Twin TAS link connectors allow system interconnection and control with other Trilogy Audio System products. TAS link allows
remote on and off switching plus status reporting of various parameters which can be displayed on your Trilogy preamplier.
See your Trilogy preamplier manual for further details.
TAS link cables of varying lengths are available from your Trilogy dealer.
Inhaltsverzeichnis
Andere Trilogy Verstärker Handbücher
Trilogy
Trilogy 903 Bedienungsanleitung
Trilogy
Trilogy 909 Bedienungsanleitung
Trilogy
Trilogy 925 Bedienungsanleitung
Trilogy
Trilogy 968 Bedienungsanleitung
Trilogy
Trilogy 931 Bedienungsanleitung
Trilogy
Trilogy H1 Bedienungsanleitung
Trilogy
Trilogy 990 Bedienungsanleitung
Trilogy
Trilogy 907 Bedienungsanleitung
