TriMark E-FOB Bedienungsanleitung

e-ASK

electronic Access Security Keyless-entry

-FOB

FOB

RF Keyless

RF Keyless-

-entry

entry

Full Function Consumer Manual

FCC ID: TV2EFOB1

(UM19 ~ 22793-01)

Table of Contents

Introduction .................................................................................. 1

e-FOB Operation and Features - Standard Mode...................... 2

e-FOB Operation and Features - Cargo Mode........................... 2

Teaching Additional FOB Transmitters ..................................... 3

Training Wireless Switches ..................................................... 4

Additional System Features........................................................ 5

Light Activation ........................................................................ 5

2nd Unlock Output................................................................... 5

3rd Unlock Output.................................................................... 5

Auxiliiary Output....................................................................... 5

2nd Auxiliary Output ................................................................ 5

Panic Mode.............................................................................. 5

Lock/Unlock Confirmation........................................................ 5

Lock/Unlock Confirmation Control........................................... 5

Emergency Override................................................................ 6

Starter Kill Feature................................................................... 6

Smart LED............................................................................... 6

Vehicle Alarm........................................................................... 6

Troubleshooting........................................................................... 7

Introduction

This manual provides the necessary information for the proper use of

TriMark’s e-FOB transmitter/receiver system. Basic functions of the

system include:

 Locking and unlocking entry and compartment doors

 Light activation

 Panic mode (standard configuration only)

 Auxiliary function support

The e-FOB system includes:

 TriMark Full-Function RF Receiver

 2 eFOB key fob transmitters

 Smart LED

 Push button switch

The TriMark Full-Function receiver and eFOB transmitters are

shipped programmed.

e-FOB Operation and Features—Standard Mode

Horn button

Unlock button

Button Function

Lock Locks all entry doors and arms security system.

Unlock Unlocks doors and disarms security system. Also

activates the porch light.

Horn button Activates panic mode when pressed and held for 2

seconds.

*button *button function is OEM/dealer defined. Possible

assignment include: interior/exterior lighting, awning

extension/retraction, gas cap, hood, etc.

Notes:

 While the engine is running only the Unlock (Entry Unlock)

function of the e-FOB remains activated — other functions are

deactivated.

*button

Lock button

e-FOB Operation and Features—Cargo Mode

Button Function

Entry Lock Locks all entry doors and arms security system.

Entry Unlock Unlocks entry doors and disarms security system. Also

activates the porch light.

Cargo Lock Locks cargo compartments and arms security system.

Cargo Unlock Unlocks compartment doors and disarms security

system.

Entry Lock

Cargo Lock Entry Unlock

Cargo Unlock

Unlock button

Teaching Additional FOB Transmitters

1. Plug the LED into C6 and the push button into C7 on the

receiver. Your OEM may have already installed these in your

vehicle.

2. Turn ignition off and disarm alarm.

3. Press and release the programming button 3 times. The LED

will turn on red after 3 seconds.

4. Press and release the Lock button of each new FOB

transmitter once. The LED will flash off and the horn will sound

once. Up to 60 transmitters may be programmed at one time.

5. Repeat step 4 until all fobs are programmed.

Notes:

 If you place the system in learn mode and teach nothing, the

system will exit in 10 seconds.

 When new transmitters are taught, all old transmitters are

erased.

 The memory for codes will not be erased if power is removed.

 As soon as the LED turns off, the system is fully functional.

Training Wireless Switches

Up to 20 wireless switches can be trained to the RF controller. A wire-

less switch can provide door ajar information, input from a shock sen-

sor, a motion sensor, a glass break sensor, etc.

1. Plug the LED into C6 and the programming button into C7 on

the receiver. Your OEM may have already installed these in

your vehicle

2. Turn ignition off and disarm alarm.

3. Press and release the programming button 5 times. The LED

will turn on green after 2 seconds.

4. Press the programming button X number of times to store the

wireless sensor in X position (1-25). The LED will briefly flash

red.

5. Remove the magnet from the wireless sensor to activate the

output. The horn will honk and the siren will sound.

6. 6. Repeat steps 4 and 5 to train additional wireless sensors. If

two sensors are trained to the same position, only the second

sensor will be active.

Notes:

 As soon as the LED turns off, the system is fully functional.

 The system exits learn mode after 10 seconds of inactivity.

 To erase all wireless sensors, turn ignition on and press the

programming button 10 times. The horn and siren will sound

once to indicate that all sensors have been erased.

 The memory for codes will not be erased if power is removed.

Additional System Features

Light Activation

When the alarm is armed, the parking lights and headlights flash. With

an unlock instruction from the key fob, the dome light stays illuminated

for 30 seconds and the parking and headlights flash.

2nd Unlock Output

Press and release the Unlock button twice to unlock the bay doors.

(Standard Mode Only)

3rd Unlock Output

The 3rd Unlock output is actuated with the unlock command and with

the secure operation (5 / 6) or (3). (Standard Mode only)

Auxiliary Output

This is OEM/dealer defined feature activated by the *button. Possible

assignments include: interior/exterior lighting, awning control, gas cap,

etc. Ask your dealer for functionality. (Standard Mode only)

2nd Auxiliary Output

The 2nd auxiliary output is actuated by holding down the Unlock (Entry

Unlock) button for two seconds. Ask your dealer for functionality.

Panic Mode

Available in standard mode. Pressing and holding the Horn button

(center left) for 2 seconds activates panic mode. During panic mode,

horn/siren is continuously activated and headlights and parking lights

flash for 30 seconds. Pressing the Unlock button deactivates panic

mode. (Standard Mode Only)

Lock/Unlock Confirmation

The horn/siren chirps once when the alarm is armed. If the alarm has

been set off since the last unlock command, the horn/siren chirps 4

times to indicate the alarm activity when the system is disarmed. The

headlights and parking lights flash once on lock and unlock.

Lock/Unlock Confirmation Control

The siren and horn confirmation is controlled by pressing lock, unlock

and auxiliary (*) buttons at the same time. A single chirp is heard when

confirmation is muted. A double chirp occurs when turned on.

(Cargo mode: Press Entry Lock, Entry Unlock and Cargo Unlock.)

Emergency Override

To disarm the alarm in case of FOB transmitter loss or malfunction:

1. Turn ignition on.

2. Press and hold the push button for 3-seconds. LED turns off.

3. Turn ignition off.

Starter Kill Feature

The starter kill feature is active for 30 minutes after the alarm is

activated.

Smart LED:

The smart LED indicates system status:

 Slow flash = Armed

 Off = Disarmed

 Fast flash = Alarm activated

Vehicle Alarm

When the alarm is armed, the parking lights flash and the horn/siren

chirps. The smart LED flashes continuously.

 In standard mode, the alarm is armed with either a single or double

Lock button press. See dealer to change this configuration.

 In cargo mode, both the Entry Lock and Cargo Lock must be

pressed within 5 seconds.

The alarm is activated with a security trigger input or if the ignition is

started. The horn/siren, parking lights and head lights flash for 30

seconds. The starter kill is activated for 30 minutes. Press the Lock or

Unlock buttons to deactivate the alarm.

There is a 5 second delay before the system will recognize a security

input after being armed. If a security input (door ajar switch, motion

sensor, glass break sensor, etc.) is triggered while the alarm is armed,

the security input must be turned off and then on before the alarm is

activated. The horn/siren chirps 3 times if a security input is active

when the alarm is armed.

The alarm is disarmed three ways.

 Press the Lock (Entry Lock) on the FOB transmitter.

 Press the Unlock (Entry Unlock) button on the transmitter.

 Turn the ignition on and hold the programming button for 5

seconds.

This product has been manufactured with methods to ensure high

quality and to meet the high expectations of our customers. TriMark

warrants this product to be free from workmanship defects and will

remedy issues per TriMark's warranty policy.

Remote transmitter FOBs, batteries, and other equipment subject to

normal wear and deterioration may need to be replaced periodically by

dealer and/or end user and are not covered by this warranty. TriMark

will not be liable for indirect, special, incidental or consequential

damages.

This system complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not cause

harmful interference and (2) This device must accept any interference

received including interference that may cause undesired operation.

Note: The manufacturer is not responsible for any radio or television

interference caused by unauthorized modification to this equipment.

Such modification could void the user’s authority to operate the

equipment. 7

Troubleshooting

Problem Description Possible Solution

e-FOB Hints

Button press does not provide

correct operation

Verify power to the RF receiver

Replace FOB transmitter battery

Re-teach the FOB transmitter to the

receiver

No operation or intermittent

operation

Mount RF receiver away from

enclosed metal areas and fully

extend antenna

Check FOB transmitter battery

voltage. Batteries need to be

changed every 1-2 years depending

on usage.

One particular e-FOB function

does not work

Check wire connection of affected

function at RF module and wiring

harness

For additional troubleshooting service, assistance, and/or warranty

information on OEM-installed systems, please contact the OEM of your

vehicle.

Andere Handbücher für e-FOB

Inhaltsverzeichnis

Andere TriMark Sender Handbücher

TriMark

TriMark e-FOB Bedienungsanleitung

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung