Triple S Wildcat Bedienungsanleitung

TABLE OF CONTENTS

Machine Components

Safety Precautions

Machine Set Up

Machine Operation

Machine Maintenance & Storage

Troubleshooting

Technical Specifications

Parts Lists

Wiring Diagram

Warranty Policy

3 - 4

8-13

SAFETY PRECAUTIONS

GROUNDING INSTRUCTIONS

General – This carpet spotting machine shall

be grounded while in use to protect the

operator from electric shock. The machine is

provided with a three-contact grounding type

attachment plug to fit the proper grounding

type receptacle. The green (or green & yellow)

conductor in the cord is the grounding wire.

Never connect this wire to other than the

grounding pin of the attachment plug.

This machine is for use on a nominal 120-volt

circuit and has a grounding plug that

resembles the plug illustrated in figure below.

Make sure that the machine is connected to

an outlet having the same configuration as the

plug. No adapter should be used with this

machine.

Grounded

3 Hole Outlet

Ground Pin

(120V)

This machine is intended for commercial use.

It is constructed for use in an indoor

environment and is not intended for any other

use. Use only recommended accessories.

All operators shall read, understand and

exercise the following safety precautions:

1) Do not operate machine:

- Unless trained and authorized

- Unless you have read and understand

operators manual

- In flammable or explosive areas.

- With damaged or modified cord or plug.

- If not in proper operating condition.

- In outdoor areas.

- In standing water.

- Without filters in place.

- With the use of unapproved extension

cords.

2) Before operating machine:

- Make sure all safety devices are in place

and operate properly.

3) When using machine:

- Mix and handle any chemicals according

to manufacturer’s recommendations

- Do not run machine over cord.

- Do not pull machine by cord or plug.

- Do not pull cord around sharp edges or

corners.

- Do not unplug by pulling on the cord.

- Do not stretch cord.

- Do not handle plug with wet hands.

- Keep cord away from heated surfaces.

- Do not pick up flammable materials or

reactive metals.

- Report machine damage or faulty

operation immediately.

4) Before leaving or servicing machine:

- Turn off machine.

- Unplug power cord from outlet.

5) When servicing machine:

- Unplug cord from outlet.

- Use manufacturer supplied or approved

replacement parts.

- Avoid moving parts. Don’t wear

loose clothing.

CARPET SPOTTER - SETUP

!!! Read operators manual thoroughly

prior to operating or servicing this

machine!!!

Carefully check the shipping carton for signs

of damage. Report any carton damage to

carrier immediately.

Check carton contents to ensure carton is

complete. Contact your distributor if anything

is missing.

Contents:

zCarpet Spotter

zVacuum & Solution hoses

zHand tool

!!! Read operators manual

thoroughly prior to operating or

servicing this machine!!!

1) Using a hose or bucket, fill tank with a

maximum of 1 gallon of water.

!!! Do not use flammable liquids or

operate machine in or near

flammable liquids or vapors!!!

2) Connect the solution hose and vacuum

hose to the machine.

3) Connect the power cable to a grounded

wall outlet. (see grounding instructions)

MACHINE OPERATION

PRIOR TO REMOVING SPOTS

1) Inspect power cable for damage.

Replace cable if damage is found.

2) Vacuum carpet to remove debris prior to

extracting the spot.

SPOT REMOVAL

1) Turn on vacuum / pump switch.

NOTE: Solution will only spray when the

spray handle(on the hand tool) is pulled.

2) To start cleaning, pull the spray handle

(hand tool) and begin to pull the tool

backwards over the spot.

NOTE: For best cleaning results, use

the built-in agitation brush on the hand

tool to help loosen stain.

3) Release spray handle when you have

reached the end of the spot. Continue to

pull hand tool back for another 4 inches to

pick up excess solution.

4) Continue until spot is removed.

OPERATING HINTS

1) Use cool water only. Hot water may set a

stain.

2) Use the built-in agitation brush to help free

up stain.

3) Continually check for foam buildup in

recovery tank. Use a distributor

recommended foam control solution.

NOTE: Excessive foam buildup will cause

damage to the vacuum motor.

4) Repeat extraction path on heavily soiled

areas.

5) When recovery of the dirty solution ends, or

the solution tank is empty, you must drain

the recovery tank. (see TANK DRAINING)

DRAINING TANKS

DRAINING SOLUTION TANK

1) Turn machine off and unplug from power

source.

2) Disconnect solution and vacuum hoses

from front of machine.

3) Unhook clamps on recovery tank and

remove recovery tank from machine.

4) Carry solution tank to an approved drain,

and dump out contents.

DRAINING RECOVERY TANK

1) Turn off machine and unplug from

power source.

2) Unhook clamps on recovery tank and

remove recovery tank from machine.

3) Carry recovery tank to an approved

drain and dump out contents.

4) Rinse recovery tank with clean water.

5) Reattach recovery tank to the solution

tank.

MACHINE MAINTENANCE

To keep the machine performing well

for many years, please follow the

following maintenance procedures.

!!! Always confirm that the machine

is unplugged prior to performing

any maintenance or repairs!!!

DAILY MAINTENANCE

1) When cleaning operation is complete

for the day, drain and rinse the

recovery tank thoroughly with clean

water.

2) Remove remaining solution from

solution tank.

3) Remove vacuum filter and rinse with

clean water.

4) Replace filter when dry.

5) Remove and inspect spray jet. If

necessary, clean jet.

NOTE: Do not clean jet with a pointed

object, as it will damage the jets.

6) Check brush strip & remove any debris

or carpet fibers.

7) Check pick up head on hand tool and

remove any debris or carpet fibers.

8) Clean machine with a nonabrasive cleaner.

9) Inspect power cable for any damage.

Replace if necessary.

MONTHLY MAINTENANCE

1) Flush pump & plumbing with an acetic

acid solution to dissolve any chemical

buildup.

Mixing Instructions:

a) Premix 8 oz. of an acetic acid solution

with 1 gallon of water and pour into

solution tank.

b) Turn vacuum / pump switch on

c) Put floor tool head over floor drain

and pull solution trigger for one (1)

minute.

d) Turn machine off and allow

remaining solution to sit in machine

overnight.

e) The following day, spray out

remaining solution and flush system

again with 1 gallon of clean water.

2) Inspect machine for water leaks.

3) Check machine for loose or missing nuts,

screw and bolts and replace as necessary.

MACHINE STORAGE

1) Prior to storing the machine, ensure the

solution and recovery tanks are clean and

empty of any solution.

2) Store machine in upright position in a dry

area, with the vacuum hose removed for

air circulation.

NOTE: If you are storing the machine in an

area which can freeze, be sure both tanks

and the solution plumbing are empty of all

water and dry!

BASIC TROUBLESHOOTING

PROBLEM CAUSE SOLUTION

Machine

doesn't work

Not plugged in to power source Plug into a grounded outlet

Faulty power cable Contact Distributor

Faulty extension power cable Replace with new extension power

cable

Building circuit breaker tripped Reset circuit breaker

Solution

pump not

working

Vacuum / pump switch not on Turn on switch

Vacuum / pump switch faulty Contact Distributor

Faulty solenoid Contact Distributor

Faulty solution pump Contact Distributor

Pump overheated Determine cause and allow 30

minutes for pump to cool

Loose or broken wiring Contact Distributor

Vacuum

motor not

working

Vacuum / pump switch not on Turn on switch

Vacuum / pump switch faulty Contact Distributor

Vacuum motor thermal overload

tripped Check for obstruction and allow 30

minutes to cool

Faulty vacuum motor Contact Distributor

Worn carbon brushes Contact Distributor

Loose or broken wiring Contact Distributor

Poor pick up

Air leaking around recovery

gasket Ensure recovery lid is firmly tightened

Vacuum gasket damaged or worn Replace gasket

Loose vacuum hose connections Ensure vacuum hose connections are

tight

Defective vacuum hose Replace vacuum hose

Loose vacuum hose cuffs Ensure cuffs are secure to the

housing

Vacuum hose clogged Remove obstruction from vacuum

hose

Uneven or

no solution

spray

Solution tank is empty or low Fill solution tank

Vacuum / pump switch not on Turn on switch

Dirty or plugged spray tips Clean or replace spray tips

Improper spray tip size or spray

angle Contact Distributor

Worn spray tips Contact Distributor

Faulty solution pump Contact Distributor

Clogged solution tank filter Clean or replace filter

Pinched or kinked solution hose Check for obstructions and kinks and

reroute or replace if needed

Gallon Capacity 1 Gal (3.79Ltr)

Cleaning Path 4" (10.2cm)

Pump 30PSI

Vac Motor 2-Stage

Voltage 110V

Waterlift 85" (215.9cm)

Cable 25ft.

Wheels 8" (203.2mm)

Vacuum Hose 8.2ft.

Solution Hose 8.5ft.

Technical Specifications:

Inhaltsverzeichnis

Andere Triple S Bodenreinigungsmaschine Handbücher

Triple S

Triple S TR Series Installations- und Betriebshandbuch

Triple S

Triple S 17 XL Installations- und Betriebshandbuch

Triple S

Triple S 20C Bedienungsanleitung

Triple S

Triple S PANTHER 15B Bedienungsanleitung

Triple S

Triple S Q-LINE Series Installations- und Betriebshandbuch

Triple S

Triple S Q-17 Installations- und Betriebshandbuch

Triple S

Triple S 20D Installations- und Betriebshandbuch

Triple S

Triple S panther 26T Bedienungsanleitung

Triple S

Triple S POWER SPOTTER 4 Installations- und Betriebshandbuch

Triple S

Triple S Q-1500 Handbuch

Triple S

Triple S Cougar 17 Bedienungsanleitung

Triple S

Triple S 20B Bedienungsanleitung

Triple S

Triple S MS-31 Installations- und Betriebshandbuch

Triple S

Triple S Ace 20T Bedienungsanleitung

Triple S

Triple S Cheetan 1500 Bedienungsanleitung

Triple S

Triple S Ace 26T1 Bedienungsanleitung

Triple S

Triple S ACHIEVER 40 Installations- und Betriebshandbuch

Triple S

Triple S JAGUAR 20R Bedienungsanleitung

Triple S

Triple S Ace 26BA1 Bedienungsanleitung

Beliebte Bodenreinigungsmaschine Handbücher anderer Marken

Nilfisk-Advance

Nilfisk-Advance Advance SC370 17B Bedienungsanleitung

Numatic

Numatic ET 4045 Bedienungsanleitung

HAWK ENTERPRISES

HAWK ENTERPRISES HP1513-180BRUTE Bedienungsanleitung

Mytee

Mytee 8070 Mytee-Lite Bedienungsanleitung

Kärcher

Kärcher B 140 R Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance SW 750 Bedienungsanleitung

Tornado

Tornado Marathon 2000 98190 Handbuch

Windsor

Windsor ADMIRAL Admiral 8 Bedienungsanleitung

Numatic

Numatic TTB 1117/100 Bedienungsanleitung

Tennant

Tennant 8210D Bedienungsanleitung

Nobles

Nobles Frontier Produkthandbuch

lavina

lavina 21-X Bedienungsanleitung

KENT

KENT Edge 28B Bedienungsanleitung

Tennant

Tennant 215 Produkthandbuch

Windsor

Windsor BDP 51/2000C Bedienungsanleitung

CleanFreak

CleanFreak DURA-18HD Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Warrior 34RST Administratorhandbuch

BETCO

BETCO PB24 Bedienungsanleitung