Triplett CTX200 Bedienungsanleitung

CTX200 RJ45/Coax Cable

Tester

USER MANUAL

99 Washington Street

Melrose, MA 02176

Phone 781-665-1400

Toll Free 1-800-517-8431

Visit us at www.TestEquipmentDepot.com

Introduction

Congratulations on your purchase the CTX200 RJ45/Coax Cable Tester. The

system consists of a Main Tester and a Remote Terminator and Preforms the

following tests: Continuity, Open & Short Circuits, Wire Crossed (Reverse and

Split) Tests CAT3, 5, 5e, 6, 6A, & 7 Ethernet Cables to TIA568 Specs • Tests

COAX Cables • Locates Cables*

WARNING!!!

DO NOT USE ON LIVE CIRCUITS!!

**NOTE: <5V/20mA rating**

Features

 Tests and tones both RJ45-CAT5/6 and coax cables.

 Ruggedized for field use. Small and easy to carry.



 PASS/FAIL results appear in one second.

 Each pair’s status is highlighted.

 Complete TIA568 test performed. Continuity, opens / shorts, reversals

and split pairs.



 Auto-off (12 seconds) to conserve battery life.

 Low battery indicator.

 (1) 9V Battery and Pouch included.

Quick Start: Cable Testing



Purpose

Ethernet cables have 4 pairs of wires (”twisted pairs”). It is important that the pairs

correctly go to connector pins 1,2 ; 3,6 ; 4,5 ; and 7,8. The Pocket CAT tests for

the proper pairing and if there is an error it will report it to you (”split pairs”)

Connecting cables to the Tester

Installed cables: Connect the Main unit to the wall jack, then connect the remote

to the patch panel or far-end wall jack

Patch cables: Attach the Main unit and Remote directly to the cable ends.

Power ON and Test

Press the ON button. Press again to begin test. When the PASS/FAIL LEDs light,

press the FAULT CHECK button to isolate any problems to an individual pair.

Coax Testing Coax is displayed using the 4/5 LEDs. The coax remote is in the

pouch.

Quick Start: Cable Locating with Tone

Purpose

Tone is used to locate a cable’s far end. A tone is placed on the cable’s

“near end” by the CTX200 Main unit. The probe locates the tone at the far

end of the cable. NOTE: Requires

Connecting cables to the Tester

Plug the cable into the tester’s Main unit.

Power ON and Tone:

Press the ON button. Hold the TONE button for 7 secs to turn ON the tone.

Press the TONE button repeatedly to select the pair you wish to tone. The

tone is loudest when you select the entire cable (including the shield).

Connecting the Cable Tester

Testing patch cables

Slide Remote Connector out from base of Pocket CAT, then connect one end of the cable

to the Remote Connector, and the other end to the Pocket CAT.

Testing installed cables

Slide Remote Connector out from base of Pocket CAT, then connect the far end of the

cable to the Remote Connector, and the other end to the Pocket CAT. NOTE: The Remote

Connector for COAX testing is located in the pouch..

Faceplate POCKET CAT FACEPLATE

Pass/Fail

Indicator

Pair/Shield

Tested

(Coax uses 4/5)

Press to test all pairs

automatically.

Press to test pairs individually. Hold 7 second for Tone and Press again to select pair.

Remote Connector: Push or Slide to Remove.

Testing RJ45 and Coax Cables

Power ON and TEST: Press the ON button. Press again to commence the test. The bright, blue

PASS LED indicates the cable has passed. If the FAIL LED lights, press the FAULT CHECK button

to isolate problems to an individual pair. See back for more examples.

OPEN: A wire is disconnected.

SHORT: A wire makes contact with

another wire.

CROSS (REVERSAL): a twisted pair

gets flipped on one side of the cable

SPLIT: One wire from each of two

different pairs gets swapped on both

ends of the cable.

Testing Examples: Coax

The Pocket CAT uses LED 4&5 to display the status of a coax cable test.. Connect the near end

of the cable to the BNC connector. Connect the far end to the coax terminator (pouch).

Good Cable:

LEDs

OFF

BLINK

Short in Cable:

LEDs

OFF

BLINK

Testing Examples: Ethernet

Ethernet cables have 4 pairs of wires (”twisted pairs”). It is important that the

pairs correctly go to connector pins 1,2; 3,6; 4,5; and 7,8. The tester tests for the

proper pairing and if there is an error it will report it to you. The follow-ing examples

are based on EIA/TIA 568B (the most popular ethernet wiring standard).

Good Cable:

Open on Pair 1-2:

Split Pairs 1-2 &3-6:

Short on Pair 3-6:

Crossed Pairs 4-5 & 7-8:

Warranty Information

Triplett / Jewell Instruments extends the following warranty to the original purchaser of

these goods for use. Triplett warrants to the original purchaser for use that the products sold

by it will be free from defects in workmanship and material for a period of (1) one year from

the date of purchase. This warranty does not apply to any of our products which have been

repaired or altered by unauthorized persons in any way or purchased from unauthorized

distributors so as, in our sole judgment, to injure their stability or reliability, or which have

been subject to misuse, abuse, misapplication, negligence, accident or which have had the

serial numbers altered, defaced, or removed. Accessories, including batteries are not

Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176

TestEquipmentDepot.com

Andere Triplett Kabeltester Handbücher

Triplett

Triplett WireMaster XR-5 Bedienungsanleitung

Triplett

Triplett TDR100 Bedienungsanleitung

Triplett

Triplett CTX200PA Bedienungsanleitung

Triplett

Triplett WireMaster HDMI2 Bedienungsanleitung

Beliebte Kabeltester Handbücher anderer Marken

Whirlwind

Whirlwind Connect DCT-9 Bedienungsanleitung

VOLTCRAFT

VOLTCRAFT CT-2 Bedienungsanleitung

Greenlee

Greenlee 45395 Bedienungsanleitung

Test-Um

Test-Um Validator-NT NT955 Bedienungsanleitung

Fluke

Fluke MicroMapper Bedienungsanleitung

Radiodetection

Radiodetection RD8100 Bedienungsanleitung

Vonaq

Vonaq EasyCheck 900 Bedienungsanleitung

Softing

Softing CableMaster CM200 Bedienungsanleitung

Microtest

Microtest 8751 Bedienungsanleitung

Psiber Data Systems

Psiber Data Systems 20 Bedienungsanleitung

Platinum Tools

Platinum Tools LANSeeker TP500C Bedienungsanleitung

Tenmars

Tenmars LC-90 Bedienungsanleitung

BIRD

BIRD SITE ANALYZER SA-1700EX Bedienungsanleitung

Softing

Softing WireXpert 4500 Bedienungsanleitung

Vision

Vision V18-310 Bedienungsanleitung

Black Box

Black Box Scan-LAN 80 Bedienungsanleitung

Besantek

Besantek BST-IT30 Bedienungsanleitung

Softing

Softing WireXpert 4500 Bedienungsanleitung