Tripp Lite BHDBT-K-E3SI-ER Bedienungsanleitung

Owner’s Manual

HDBaseT HDMI Over Cat5e/6/6a

Extenders

Models:

BHDBT-K-E3SI-ER, BHDBT-K-E3SI-LR, BHDBT-K-E3SPI-L,

BHDBT-K-PI, BHDBT-K-PI-LR, BHDBT-K-SPI

PROTECT YOUR INVESTMENT!

and ultimate peace of mind.

You could also win an ISOBAR6ULTRA

surge protector—a $100 value!

www.tripplite.com/warranty

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

All trademarks are the sole property of their respective owners.

16-02-143-933493-EN.indd 1 2/16/2016 2:39:28 PM

Table of Contents

Package Contents

Package Contents 2

Product Features 3

HDBaseT Features Chart 3

Maximum Distance and Video Resolution 4

Optional Accessories 4

Mounting Instructions 5

Installation 6

Troubleshooting 9

Warranty and Product Registration 10

Regulatory Compliance 11

BHDBT-K-E3SI-ER

BHDBT-K-E3SI-LR

BHDBT-K-E3SPI-L

BHDBT-K-PI

BHDBT-K-PI-LR

BHDBT-K-SPI

External Power Supply (1 or 2) 2 2 1 1 1 1

IR-In Cables 1 1 1 1 1 1

IR-Out Cables 1 1 1 1 1 1

Mounting Hardware Y Y Y Y Y Y

Owner’s Manual Y Y Y Y Y Y

16-02-143-933493-EN.indd 2 2/16/2016 2:39:28 PM

Product Features

HDBaseT Features Chart

BHDBT-K-E3SI-ER

BHDBT-K-E3SI-LR

BHDBT-K-E3SPI-L

BHDBT-K-PI

BHDBT-K-PI-LR

BHDBT-K-SPI

HDMI Audio/Video Y Y Y Y Y Y

10/100 Ethernet Y Y Y N N N

RS-232 Serial Y Y Y N N Y

IR Remote Control Y Y Y Y Y Y

Power over Ethernet (PoE) N N Y Y Y Y

Note: This section lists features for all HDBaseT models referenced in this manual. See the HDBaseT

Features Chart below to determine which features your model supports.

• Supports Ultra High Deﬁnition (UHD) 4k x 2k video resolutions up to 3840 x 2160,

and High Deﬁnition (HD) video resolutions up to 1920 x 1080 (1080p)

• Extends HDMI audio/video, Ethernet, RS-232 Serial and IR Control signals over a

single Cat5/6/6a cable

• Power over Ethernet (PoE) powers the receiver unit over Cat5/6/6a cable, eliminating

the need for an external power supply at the receiver

• Ethernet models feature three 10/100 Ethernet ports on both the transmitter unit

and the receiver unit for communication between devices and access to online

content

• Extends a full duplex RS-232 serial signal, such as from a touchscreen monitor;

baud rates up to 115Kbps are supported

• IR Control lets you use your HDMI source’s remote control in the same location as

your extended monitor, or your monitor’s remote control in the same location as

your source; uses a 39KHz IR frequency

• Plug-and-play; no software or drivers are required

16-02-143-933493-EN.indd 3 2/16/2016 2:39:28 PM

Optional Accessories

• N001-Series Cat5e Patch Cables

• N022-01K-GY Cat5e 24 AWG Solid Wire Bulk Cable – 1,000 ft.

• N202-Series Cat6 24 AWG Solid Wire Patch Cables

• N222-01K-BL Cat6 24 AWG Solid Wire Bulk Cable – 1,000 ft.

• N261-Series Cat6a UTP Snagless Patch Cables

• N262-Series Cat6a STP Snagless Patch Cables

• P569-XXX-LOCK High-speed HDMI Cables with Ethernet and Locking Connectors

Maximum Distance and Video Resolution

Model

4K Max

Distance –

Cat6a

4K Max

Distance –

Cat5e/6

1080p Max

Distance –

Cat6a

1080p Max

Distance –

Cat5e/6

BHDBT-K-E3SI-ER N/A N/A 500 ft. (150 m)* 500 ft. (150 m)*

BHDBT-K-E3SI-LR 328 ft. (100 m) 230 ft. (70 m) 328 ft. (100 m) 328 ft. (100 m)

BHDBT-K-E3SPI-L 328 ft. (100 m) 230 ft. (70 m) 328 ft. (100 m) 328 ft. (100 m)

BHDBT-K-PI 130 ft. (40 m) 115 ft. (35 m) 230 ft. (70 m) 200 ft. (60 m)

BHDBT-K-PI-LR 328 ft. (100 m) 230 ft. (70 m) 328 ft. (100 m) 328 ft. (100 m)

BHDBT-K-SPI 130 ft. (40 m) 115 ft. (35 m) 230 ft. (70 m) 200 ft. (60 m)

* When using the BHDBT-K-E3SI-ER to extend a 1080p (60Hz) signal at the maximum distance of

500 ft., the color depth of the source must be set to 8-bit.

•

16-02-143-933493-EN.indd 4 2/16/2016 2:39:28 PM

Mounting Instructions

The HDBaseT HDMI Over Cat5e/6/6a Extender products come with mounting hardware

that allows them to be mounted in a variety of ways. The following images show the

different ways the included mounting brackets can be attached for different mounting

methods.

Note: The images below show a B126-1A1 unit, but mounting is the same for the HDBaseT extender

products.

Wallmount

19” rackmount Pole Mount

•

16-02-143-933493-EN.indd 5 2/16/2016 2:39:29 PM

Installation

Notes:

1. See the Maximum Distance and Video Resolution table on page 4 for information on your model’s

maximum supported distances and resolutions.

2. Test to make sure the entire installation works properly before pulling cables through ceilings/walls.

3. To achieve maximum distance and performance, use 24 AWG solid wire Cat5e/6 or 23 AWG solid

wire Cat6a cable. Using stranded wire cable or cable with a gauge (AWG) size higher than that

recommended will result in a shorter extension distance. Higher gauge cabling such as 26 AWG

has a more limited transmission capability then lower-gauge cabling. All Tripp Lite N202-Series

Cat6 cables are made with 24 AWG solid wire cabling. Extended lengths of 23 AWG solid wire

Cat6a cable are available from Tripp Lite as a custom order.

4. When using a 28 AWG HDMI cable and displaying video resolutions higher than 1080p, the HDMI

cables connecting the source and the monitor must not exceed 6 feet. When using a 24 AWG

HDMI cable, you must not exceed a 16-foot length. For best results, use Tripp Lite’s

P569-XXX-LOCK series high-speed HDMI cables with Ethernet and locking connectors.

5. The transmitter and receiver included in each kit are compatible with each other only. You

cannot mix and match transmitters and receivers from different kits. For example, a BHDBT-K-PI

transmitter will not work with a BHDBT-K-PI-LR receiver.

6. Each kit includes one set of IR-IN and IR-OUT cables. It is up to the user to determine whether

the cables will be used to extend an IR signal from the transmitter side to the receiver side, or

the receiver side to the transmitter side. In most installations, the cables will be used to control

the HDMI source (e.g. Blu-rayTM player) from the same location as the monitor connected to the

receiver.

7. The diagram below shows a BHDBT-K-E3SPI-LR installation. See the HDBaseT Features Chart on

page 3 of this manual for the features your product supports.

Remote

Receiver

Blu-ray Player

LAN

Local

Transmitter

Bar Code Scanner

or Touchscreen

Flat Panel

Computer

16-02-143-933493-EN.indd 6 2/16/2016 2:39:30 PM

1. Make sure the HDMI and RS-232 serial source is powered off.

2. Connect the HDMI source to the HDMI input port on the local transmitter unit.

3. Connect RS-232 serial DB9 cable (not included) to the RS-232 port on the local

transmitter unit, then connect to computer.*

4. If you are using a remote control on the transmitter side of the installation to

control a device on the receiver side (such as a TV), connect the IR-IN cable (with

red 3.5 mm connector) to the IR-IN port on the local transmitter unit.

Note: The IR-IN unit accepts a signal from a remote control and sends it to a device that is

controlled on the other end of the installation. Position the IR-IN unit in an unobstructed area

that can easily accept a remote control signal.

5. If you are using a remote control on the receiver side of the installation to control a

device on the transmitter side (such as a Blu-ray player), connect the IR-OUT cable

(with green 3.5 mm connector) to the IR-OUT port on the local transmitter unit.

Note: The IR-OUT unit receives the signal from the remote control on the other end of the

installation and sends it to the device being controlled. Locate the IR-OUT unit in an area close

to the remote-controlled device (e.g., Blu-ray player, TV).

6. Connect the three 10/100 Ethernet ports on the transmitter unit to your devices

(e.g., Blu-ray player, cable box, etc.) and/or a LAN.*

7. Connect the external power supply to the local transmitter unit and plug it into a

Tripp Lite Surge Protector, Uninterruptible Power Supply (UPS) or Power Distribution

Unit (PDU).

8. Connect the RJ45 output port on the local transmitter unit to the RJ45 input port

on the remote receiver unit using Cat5e/6/6a cable.

9. Connect the HDMI monitor to the HDMI output port on the remote receiver unit.

10. Connect the RS-232 serial DB9 male cable to the RS-232 port on the remote

receiver unit, then connect the RS-232 device.*

11. If you are using a remote control on the receiver side of the installation to control a

device on the transmitter side (such as a Blu-ray player), connect the IR-IN cable

(with red 3.5 mm connector) to the IR-IN port on the remote receiver unit.

Note: The IR-IN unit accepts a signal from a remote control and sends it to a device controlled

on the other end of the installation. Position the IR-IN unit in an unobstructed area that can

easily accept a remote control signal.

* See the HDBaseT Features Chart on page 3 of this manual for the features your product supports.

Installation

16-02-143-933493-EN.indd 7 2/16/2016 2:39:30 PM

Installation

12. If you are using a remote control on the transmitter side of the installation to

control a device on the receiver side (such as a TV), connect the IR-OUT cable

(with green 3.5 mm connector) to the IR-OUT port on the remote receiver unit.

Note: The IR-OUT unit receives the signal from the remote control on the other end of the

installation and sends it to the device being controlled. Locate the IR-OUT unit in an area close

to the remote-controlled device (e.g. Blu-ray player, TV).

13. Connect the three 10/100 Ethernet ports on the receiver unit to your devices

(e.g. monitor, etc.) and/or a LAN.*

14. Connect the external power supply to the remote receiver unit and plug it into a

Tripp Lite Surge Protector, Uninterruptible Power Supply (UPS) or Power Distribution

Unit (PDU). Models that support PoE will not require power at the receiver.*

15. Turn on the power to the HDMI source and RS-232 serial source.

* See the HDBaseT Features Chart on page 3 of this manual for the features your product supports.

16-02-143-933493-EN.indd 8 2/16/2016 2:39:30 PM

Troubleshooting

If you are unable to obtain an acceptable image after following these installation

instructions, try the following troubleshooting tips:

1. Are the external power supplies that came with the product connected and

plugged into a working power source? For the product to function properly, it

must be connected to and receiving power from the external power supply.

2. Was the power to the connected devices turned off prior to installation? If

not, restart them.

3. What resolution are you trying to reach? Make sure that the desired resolution

is supported by your model’s maximum distance and resolution speciﬁcations as

listed in the Product Features section of this manual. The shorter the extension

distance, the higher the resolution you will be able to obtain. If you are not able to

get an acceptable image, try lowering your computer’s video resolution or adjusting

the refresh rate.

4. What type of cabling are you using? Inferior cabling can result in poor

performance, so it is important to use cables that support the video resolution you

are trying to obtain. To achieve maximum distance and resolution, 24 AWG solid

wire Cat5e/6 cable or 23 AWG solid wire Cat6a cable must be used. Tripp Lite’s

N202-Series Cat6 cables are made with 24 AWG solid wire, as are the

N022-01K-GY (Cat5e) and N222-01K-GY bulk cables. Extended lengths of

23 AWG solid wire Cat6a cable is available from Tripp Lite as a custom order. The

HDMI cables you are using must also support the video resolution you are trying

to obtain. Inexpensive, low quality HDMI cables may not support the maximum

resolution. When using a 28 AWG HDMI cable and displaying video resolutions

higher than 1080p, the HDMI cables connecting the source and the monitor must

not exceed 6 feet. When using a 24 AWG HDMI cable, you must not exceed a

16-foot length. For best results, use Tripp Lite’s P569-XXX-LOCK series high-speed

HDMI cables with Ethernet and locking connectors.

5. Test your cables to ensure they are working properly. For example, connect

your HDMI cables between a source and a monitor that you know works to see if

the cable is functioning. For Cat5e/6 cable, connect it between a computer and a

network to verify that it establishes a network connection.

6. Do you have any patch panels or other devices between the transmitter,

repeater, and receiver units? Tripp Lite’s HDBaseT HDMI over Cat5e/6/6a

extender products are designed to be connected directly from the transmitter to

the transceiver and/or receiver with UTP cable. The more connection points that

are between the source and the remote monitor, the more likely it will be that

signal degradation will occur, causing poor performance. If you have a patch panel

or other device in-between, it should be removed from the installation.

16-02-143-933493-EN.indd 9 2/16/2016 2:39:30 PM

Troubleshooting

7. Check your cabling for any damages that may have occurred during

installation. If a cable connector is loosened from being pulled through ceilings/

walls or the cable jacket is damaged causing the wiring to be exposed, you will not

be able to achieve maximum performance.

8. Are the transmitter and/or receiver located in an area that exposes them to

higher temperatures? If the product overheats, it will not function properly.

Warranty and Product Registration

1-Year Limited Warranty

TRIPP LITE warrants its products to be free from defects in materials and workmanship for a period of one (1) year

from the date of initial purchase. TRIPP LITE’s obligation under this warranty is limited to repairing or replacing (at its

sole option) any such defective products. To obtain service under this warranty, you must obtain a Returned Material

Authorization (RMA) number from

TRIPP LITE or an authorized TRIPP LITE service center. Products must be returned to TRIPP LITE or an authorized TRIPP

LITE service center with transportation charges prepaid and must be accompanied by a brief description of the problem

encountered and proof of date and place of purchase. This warranty does not apply to equipment which has been

damaged by accident, negligence or misapplication or has been altered or modiﬁed in any way.

EXCEPT AS PROVIDED HEREIN, TRIPP LITE MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES

OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Some states do not permit limitation or exclusion of

implied warranties; therefore, the aforesaid limitation(s) or exclusion(s) may not apply to the purchaser.

EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL TRIPP LITE BE LIABLE FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL

OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF THIS PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF

SUCH DAMAGE. Speciﬁcally, TRIPP LITE is not liable for any costs, such as lost proﬁts or revenue, loss of equipment, loss

of use of equipment, loss of software, loss of data, costs of substitutes, claims by third parties, or otherwise.

PRODUCT REGISTRATION

Visit www.tripplite.com/warranty today to register your new Tripp Lite product. You’ll be automatically entered into a drawing

for a chance to win a FREE Tripp Lite product!*

* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.

16-02-143-933493-EN.indd 10 2/16/2016 2:39:30 PM

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Tripp Lite Extender Handbücher

Tripp Lite

Tripp Lite 0DT23008 Bedienungsanleitung

Tripp Lite

Tripp Lite B162-001-POE Bedienungsanleitung

Tripp Lite

Tripp Lite B132-002A-2 Bedienungsanleitung

Tripp Lite

Tripp Lite P130-000-AUDIO2 Bedienungsanleitung

Tripp Lite

Tripp Lite B203-104-PNP Bedienungsanleitung

Tripp Lite

Tripp Lite B013-HU-4K Bedienungsanleitung

Tripp Lite

Tripp Lite B127U-111-PDPD Bedienungsanleitung

Tripp Lite

Tripp Lite P167-000 Bedienungsanleitung

Tripp Lite

Tripp Lite B013-330 Bedienungsanleitung

Tripp Lite

Tripp Lite B203-101-PNPINT Bedienungsanleitung

Tripp Lite

Tripp Lite U444-06N-HD Bedienungsanleitung

Tripp Lite

Tripp Lite P130-000-AUD4K6 Bedienungsanleitung

Tripp Lite

Tripp Lite U007-40M Bedienungsanleitung

Tripp Lite

Tripp Lite B126-1A1 Bedienungsanleitung

Tripp Lite

Tripp Lite B140-101 Bedienungsanleitung

Tripp Lite

Tripp Lite B127A-002-BH Bedienungsanleitung

Tripp Lite

Tripp Lite B126-1A1-PLHD Bedienungsanleitung

Tripp Lite

Tripp Lite B203-101-IND Bedienungsanleitung

Tripp Lite

Tripp Lite B140-002-DD Bedienungsanleitung

Tripp Lite

Tripp Lite B122-000 Bedienungsanleitung

Tripp Lite

Tripp Lite B126-1A1SR Bedienungsanleitung

Tripp Lite

Tripp Lite B127U-002-PDPH2 Bedienungsanleitung

Tripp Lite

Tripp Lite B126-1P0-WP-1 Bedienungsanleitung

Tripp Lite

Tripp Lite B127A-1A1-BDBD Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung

SECO-LARM

SECO-LARM ENFORCER EVT-PB1-V1TGQ Bedienungsanleitung