Tripp Lite BHDBT-K-SI Bedienungsanleitung

Owner’s Manual

HDBaseT HDMI Over Cat5/Cat6

Extenders

Extender Kit Models:

BHDBT-K-SI, BHDBT-K-SI-ER, BHDBT-K-SI-LR

Matrix Transmitter Models:

BHDBT-T-SI-4X2, BHDBT-T-SI-4X4

Transceiver Models:

BHDBT-TR-SI, BHDBT-TR-SI-ER, BHDBT-TR-SI-LR

Receiver Models:

BHDBT-R-SI, BHDBT-R-SI-ER, BHDBT-R-SI-LR

PROTECT YOUR INVESTMENT!

and ultimate peace of mind.

You could also win an ISOBAR6ULTRA

surge protector—a $50 value!

www.tripplite.com/warranty

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

All trademarks are the sole property of their respective owners.

15-01-181-933418.indd 1 2/6/2015 3:33:55 PM

Table of Contents

Package Contents

Package Contents 2

Product Features 3

Optional Accessories 5

Mounting Instructions 5

Installation 6

Standard Extender Kit Installation 6

Extender Kit with Transceiver Installation 8

Matrix Transmitter Installation 10

RS-232 Serial Control (Matrix Transmitter Units Only) 13

Troubleshooting 14

Warranty and Product Registration 15

Regulatory Compliance 16

BHDBT-K-SI

BHDBT-K-SI-ER

BHDBT-K-SI-LR

BHDBT-T-SI-4X4

BHDBT-T-SI-4X2

BHDBT-TR-SI

BHDBT-TR-SI-ER

BHDBT-TR-SI-LR

BHDBT-R-SI

BHDBT-R-SI-ER

BHDBT-R-SI-LR

Transmitter (T), Transceiver (TR),

Receiver (R), Kit (K)

K K K T T TR TR TR R R R

External Power Supply (1, 2) 2 2 2 1 1 1 1 1 1 1 1

IR-In Cables (0, 1, 2) 1 1 1 0 0 0 0 0 1 1 1

IR-Out Cables (0, 1, 2) 1 1 1 0 0 0 0 0 1 1 1

Remote Control N N N Y Y N N N N N N

IR Extension Cable 0 0 0 1 1 0 0 0 0 0 0

3.5 mm to DB9 M/F Adapter Cable 1 1 1 1 1 0 0 0 1 1 1

3.5 mm to DB9 M/M Adapter Cable 1 1 1 0 0 0 0 0 1 1 1

Mounting Hardware Y Y Y Y Y Y Y Y Y Y Y

Owner’s Manual Y Y Y Y Y Y Y Y Y Y Y

15-01-181-933418.indd 2 2/6/2015 3:33:56 PM

Product Features

• Extends HDMI audio/video, RS-232 Serial and IR Control Signals over Cat5/6

cabling.

• Supports 7.1-channel surround sound, DTS-HD and Dolby True HD audio.

• Uses a 39 KHz IR frequency.

• Supports RS-232 Serial full-duplex baud rates up to 3 Mbps.

• EDID, HDCP and 3D compatible.

• Includes mounting hardware that allows unit to be wall-mounted, rack mounted or

pole mounted.

• Matrix transmitter units allow multiple HDMI inputs to be connected and distributed

among multiple outputs.

• Transceiver units extend and expand your installation, allowing for multiple monitor

connections at different points in a chain. Up to ﬁve (5) transceivers and one

(1) receiver can be connected in a chain, with each unit being able to extend

its maximum distance from the previous unit (see the table below for details on

maximum distances supported).

• Plug and play; no software or drivers required.

15-01-181-933418.indd 3 2/6/2015 3:33:56 PM

Product Features

Model

Unit Type

4K Max

Distance –

Cat6a

4K Max

Distance –

Cat5e / Cat6

1080p Max

Distance –

Cat6a

1080p Max

Distance –

Cat5e / Cat6

Compatible

Models

A. BHDBT-K-SI

Kit 130 ft.

(40 m)

115 ft.

(35 m)

230 ft.

(70 m)

200 ft.

(60 m)

B. BHDBT-K-SI-ER

Kit N/A N/A

500 ft.

(150 m)

500 ft.

(150 m)

C. BHDBT-K-SI-LR

Kit

328 ft.

(100 m)

230 ft.

(70 m)

328 ft.

(100 m)

328 ft.

(100 m)

D. BHDBT-T-SI-4X4

Matrix

Transmitter

Install

Based*

Install

Based*

Install

Based*

Install

Based*

F, G, H, I,

J, K

E. BHDBT-T-SI-4X2

Matrix

Transmitter

Install

Based*

Install

Based*

Install

Based*

Install

Based*

F, G, H, I,

J, K

F. BHDBT-TR-SI

Transceiver 130 ft.

(40 m)

115 ft.

(35 m)

230 ft.

(70 m)

200 ft.

(60 m)

A, D, E, I

G. BHDBT-TR-SI-ER

Transceiver N/A N/A

500 ft.

(150 m)

500 ft.

(150 m)

B, D, E, J

H. BHDBT-TR-SI-LR

Transceiver

328 ft.

(100 m)

230 ft.

(70 m)

328 ft.

(100 m)

328 ft.

(100 m)

C, D, E, K

I. BHDBT-R-SI

Receiver 130 ft.

(40 m)

115 ft.

(35 m)

230 ft.

(70 m)

200 ft.

(60 m)

D, E, F

J. BHDBT-R-SI-ER

Receiver N/A N/A

500 ft.

(150 m)

500 ft.

(150 m)

D, E, G

K. BHDBT-R-SI-LR

Receiver

328 ft.

(100 m)

230 ft.

(70 m)

328 ft.

(100 m)

328 ft.

(100 m)

D, E, H

* The BHDBT-T-SI-4X4 and BHDBT-T-SI-4X2 are compatible with all transceiver and receiver units.

The max distance that can be achieved will be determined by the transceiver and/or receiver being

used.

15-01-181-933418.indd 4 2/6/2015 3:33:56 PM

Optional Accessories

Mounting Instructions

• N001-Series Cat5 Patch Cables

• N022-01K-GY Cat5 24 AWG Solid Wire Bulk Cable – 1,000 ft.

• N202-Series Cat6 24 AWG Solid Wire Patch Cables

• N222-01K-BL Cat6 24 AWG Solid Wire Bulk Cable – 1,000 ft.

• P520-006 RS232 Serial Extension Cable – 6 ft.

• P568-Series High Speed HDMI Cables

The HDBaseT HDMI Over Cat5 / Cat6 Extender products come with mounting hardware

that allows them to be mounted in a variety of ways. The following images show the

different ways the included mounting brackets can be attached for different mounting

methods.

Note: The images below show a B126-1A1 unit, but mounting is the same for the HDBaseT extender

products.

Wallmount

19” rackmount Pole Mount

15-01-181-933418.indd 5 2/6/2015 3:33:57 PM

Installation

Standard Extender Kit Installation

Notes:

1. See the Product Features section of this manual for information on your model’s maximum

supported distances and resolutions.

2. Test to make sure the entire installation works properly before pulling cables through ceilings/walls.

3. To achieve maximum distance and performance, use 24 AWG solid wire Cat5e/6 or 23 AWG solid

wire Cat6a cable. Using stranded wire cable or cable with a gauge (AWG) size higher than that

recommended will result in a shorter extension distance. Higher gauge cabling such as 26 AWG

has a more limited transmission capability than lower-gauge cabling. All Tripp Lite N202-Series

Cat6 cables are made with 24 AWG solid wire cabling. Extended lengths of 23 AWG solid wire

Cat6a cable are available from Tripp Lite as a custom order.

4. When using a 28 AWG HDMI cable and displaying video resolutions higher than 1080p, the HDMI

cables connecting the source and the monitor must not exceed 6 feet. When using a 24 AWG

HDMI cable, you must not exceed a 16-foot length.

5. The transmitter and receiver included in each kit are compatible with each other only. You

cannot mix and match transmitters and receivers from different kits. For example, a BHDBT-K-SI

transmitter will not work with a BHDBT-K-SI-ER receiver.

6. Each kit includes one set of IR-IN and IR-OUT cables. It is up to the user to determine whether

the cables will be used to extend an IR signal from the transmitter side to the receiver side, or

the receiver side to the transmitter side. In most installations, the cables will be used to control

the HDMI source (e.g., Blu-ray player) from the same location as the monitor connected to the

receiver.

HDMI Cable Remote

Receiver

HDMI Cable

RS232

Serial

IR-OUT

IR-IN

Blu-Ray Player

Local

Transmitter

RS232

Serial

IR-OUT

IR-IN

Bar Code Scanner

or Touch Screen

Flat Panel

Computer

15-01-181-933418.indd 6 2/6/2015 3:33:58 PM

1. Make sure that the HDMI and RS-232 serial source is powered off.

2. Connect the HDMI source to the HDMI Input port on the local transmitter unit.

3. Connect the included 3.5 mm Male-to-DB9 female adapter cable to the RS-232

port on the local transmitter unit, then connect the computer to the adapter.

4. Connect the IR-IN cable to the IR-IN port on the local transmitter unit.

Note: The IR-IN unit accepts a signal from a remote control and sends it to a device that is

controlled on the other end of the installation. Position the IR-IN unit in an unobstructed area

that can easily accept a remote control signal.

5. Connect the IR-OUT cable to the IR-OUT port on the local transmitter unit.

Note: The IR-OUT unit receives the signal from the remote control on the other end of the

installation and sends it to the device being controlled. Locate the IR-OUT unit in an area close

to the remote-controlled device (e.g., Blu-Ray player, TV).

6. Connect the external power supply to the local transmitter unit and plug it into a

Tripp Lite Surge Protector, Uninterruptible Power Supply (UPS) or Power Distribution

Unit (PDU).

7. Connect the RJ45 Output port on the local transmitter unit to the RJ45 Input port

on the remote receiver unit using Cat5e/6/6a cable.

8. Connect the HDMI monitor to the HDMI Output port on the remote receiver unit.

9. Connect the included 3.5 mm male-to-DB9 male adapter cable to the RS-232

port on the remote receiver unit, then connect the RS-232 device to the adapter.

10. Connect the IR-IN cable to the IR-IN port on the remote receiver unit.

Note: The IR-IN unit accepts a signal from a remote control and sends it to a device controlled

on the other end of the installation. Position the IR-IN unit in an unobstructed area that can

easily accept a remote control signal.

11. Connect the IR-OUT cable to the IR-OUT port on the remote receiver unit.

Note: The IR-OUT unit receives the signal from the remote control on the other end of the

installation and sends it to the device being controlled. Locate the IR-OUT unit in an area close

to the remote-controlled device (e.g., Blu-ray player, TV).

12. Connect the external power supply to the remote receiver unit and plug it into a

Tripp Lite Surge Protector, Uninterruptible Power Supply (UPS) or Power Distribution

Unit (PDU).

13. Turn on the power to the HDMI source and RS-232 serial source.

Installation

15-01-181-933418.indd 7 2/6/2015 3:33:58 PM

Installation

Extender Kit with Transceiver Installation

Notes:

1. The below installation diagram and instructions are for an HDBaseT HDMI over Cat5 Extender Kit

installation, though installation will be similar if you purchase the transmitter and receiver units

separately.

2. See the Product Features section of this manual for models compatible with your transceiver and

for information on the maximum supported distances and resolutions for your model.

3. Although transceiver units transmit RS-232 serial and IR Control signals from the transmitter to

the receiver, they do not feature their own RS-232 and IR Control ports.

4. Test to make sure the entire installation works properly before pulling cables through ceilings/walls.

5. To achieve maximum distance and performance, use 24 AWG solid wire Cat5e/6 or 23 AWG solid

wire Cat6a cable. Using stranded wire cable or cable with a gauge (AWG) size higher than that

recommended will result in a shorter extension distance. Higher gauge cabling such as 26 AWG

has a more limited transmission capability than lower gauge cabling. All Tripp Lite N202-Series

Cat6 cables are made with 24 AWG solid wire cabling. Extended lengths of 23 AWG solid wire

Cat6a cable is available from Tripp Lite as a custom order.

6. When using a 28 AWG HDMI cable and displaying video resolutions higher than 1080p, the HDMI

cables connecting the source and the monitor must not exceed 6 feet. When using a 24 AWG

HDMI cable, you must not exceed a 16-foot length.

7. Each kit includes one set of IR-IN and IR-OUT cables. It is up to the user to determine whether

the cables will be used to extend an IR signal from the transmitter side to the receiver side, or the

receiver side to the transmitter side. In most installations, the cables will be used to control the

HDMI source (e.g., Blu-ray player) from the same location as the monitor connected to the receiver.

HDMI Cable Remote

Receiver

HDMI Cable

RS232

Serial

IR-OUT

IR-IN

Blu-Ray Player

Local

Transmitter

RS232

Serial

IR-OUT

IR-IN

Bar Code Scanner

or Touch Screen

Connect

up to 4

Transceivers

Flat Panel

Computer

1. Make sure that the HDMI source and RS-232 serial source is powered off.

2. Connect the HDMI source to the HDMI Input port on the local transmitter unit.

3. Connect the included 3.5 mm male-to-DB9 female adapter cable to the RS-232

port on the local transmitter unit, then connect the computer to the adapter.

15-01-181-933418.indd 8 2/6/2015 3:33:59 PM

Installation

4. Connect the IR-IN cable to the IR-IN port on the local transmitter unit.

Note: The IR-IN unit accepts a signal from a remote control and sends it to a device controlled

on the other end of the installation. Position the IR-IN unit in an unobstructed area that can

easily accept a remote control signal.

5. Connect the IR-OUT cable to the IR-OUT port on the local transmitter unit.

Note: The IR-OUT unit receives a signal from the remote control on the other end of the

installation and sends it to the device being controlled. Locate the IR-OUT unit in an area close

to the remote-controlled device (e.g., Blu-ray player, TV).

6. Connect the external power supply to the local transmitter unit and plug it into a

Tripp Lite Surge Protector, Uninterruptible Power Supply (UPS) or Power Distribution

Unit (PDU).

7. Connect the RJ45 Output port on the local transmitter unit to the RJ45 Input port

on the transceiver unit using Cat5e/6/6a cable.

8. (Optional) Connect the HDMI monitor to the HDMI Output port on the transceiver

unit.

9. Connect the external power supply to the transceiver unit and plug it into a Tripp Lite

Surge Protector, Uninterruptible Power Supply (UPS) or Power Distribution Unit (PDU).

Up to ﬁve transceiver units can be inserted in-between the transmitter and receiver

units of your HDBaseT HDMI over Cat5 Extender Kit. To connect additional transceiver

units, repeat steps 7through 9. To complete your installation with a receiver unit,

proceed to step 10.

10. Connect the RJ45 Output port on the last transceiver unit in the chain to the RJ45

Input port on the receiver unit using Cat5e/6/6a cable.

11. Connect the HDMI monitor to the HDMI Output port on the remote receiver unit.

12. Connect the included 3.5 mm male-to-DB9 male adapter cable to the RS-232

port on the remote receiver unit, then connect the RS-232 device to the adapter.

13. Connect the IR-IN cable to the IR-IN port on the remote receiver unit.

Note: The IR-IN unit accepts a signal from a remote control and sends it to a device controlled

on the other end of the installation. Position the IR-IN unit in an unobstructed area that can

easily accept a remote control signal.

14. Connect the IR-OUT cable to the IR-OUT port on the remote receiver unit.

Note: The IR-OUT unit receives the signal from the remote control on the other end of the

installation and sends it to the device being controlled. Locate the IR-OUT unit in an area close

to the remote-controlled device (e.g., Blu-ray player, TV).

15. Connect the external power supply to the remote receiver unit and plug it into a

Tripp Lite Surge Protector, Uninterruptible Power Supply (UPS) or Power Distribution

Unit (PDU).

16. Turn on the power to the HDMI source and RS-232 serial source.

15-01-181-933418.indd 9 2/6/2015 3:33:59 PM

Installation

Matrix Transmitter Installation

Notes:

1. The below installation diagram and instructions are for a standard HDBaseT HDMI over Cat5

Matrix Transmitter installation. For instructions on adding transceivers to your installation, refer to

the Extender Kit with Transceiver Installation section.

2. The installation diagram below shows a BHDBT-T-SI-4X2. Installation will be the same for the

BHDBT-T-SI-4X4, except for the number of HDMI Output ports.

3. See the Product Features section of this manual for models compatible with your Matrix

Transmitter and for information on your model’s maximum supported distances and resolutions.

4. Test to make sure the entire installation works properly before pulling cables through ceilings/walls.

5. To achieve maximum distance and performance, use 24 AWG solid wire Cat5e/6 or 23 AWG solid

wire Cat6a cable. Using stranded wire cable or cable with a gauge (AWG) size higher than that

recommended will result in shorter extension distance. Higher gauge cabling such as 26 AWG has

a more limited transmission capability than lower gauge cabling. All Tripp Lite N202-Series Cat6

cables are made with 24 AWG solid wire cabling. Extended lengths of 23 AWG solid wire Cat6a

cable is available from Tripp Lite as a custom order.

6. When using a 28 AWG HDMI cable and displaying video resolutions higher than 1080p, the HDMI

cables connecting the source and the monitor must not exceed 6 feet. When using a 24 AWG

HDMI cable, you must not exceed a 16-foot length.

7. Each receiver unit includes one set of IR-IN and IR-OUT cables. It is up to the user to determine

whether the cables will be used to extend an IR signal from the transmitter side to the receiver

side, or the receiver side to the transmitter side. In most installations, the cables will be used to

control the HDMI source (e.g., Blu-ray player) from the same location as the monitor connected to

the receiver.

Display 1

Display 2

4Kx2K Player

HD Satellite

Game Console

Media Server

IR Control Pad

Super Terminal

for RS232

IR-IN/IR-OUT Units

15-01-181-933418.indd 10 2/6/2015 3:33:59 PM

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Tripp Lite Extender Handbücher

Tripp Lite

Tripp Lite B162-100-POE Bedienungsanleitung

Tripp Lite

Tripp Lite 8TLP167000 Bedienungsanleitung

Tripp Lite

Tripp Lite B127-1A1-HH Bedienungsanleitung

Tripp Lite

Tripp Lite B126-1P0-WP-1 Bedienungsanleitung

Tripp Lite

Tripp Lite 0DT23001 Bedienungsanleitung

Tripp Lite

Tripp Lite B126-1A1SR Bedienungsanleitung

Tripp Lite

Tripp Lite B126-1A1SR Bedienungsanleitung

Tripp Lite

Tripp Lite B140-002-DD Bedienungsanleitung

Tripp Lite

Tripp Lite B136-101 Bedienungsanleitung

Tripp Lite

Tripp Lite B121-000 Bedienungsanleitung

Tripp Lite

Tripp Lite B120-000-SL Bedienungsanleitung

Tripp Lite

Tripp Lite B164-101-WIR Bedienungsanleitung

Tripp Lite

Tripp Lite B132-100A Bedienungsanleitung

Tripp Lite

Tripp Lite B150-1A1-HDMI Bedienungsanleitung

Tripp Lite

Tripp Lite B150-1A1-DVI Bedienungsanleitung

Tripp Lite

Tripp Lite B132-100A Bedienungsanleitung

Tripp Lite

Tripp Lite B127-002-D2H Bedienungsanleitung

Tripp Lite

Tripp Lite B127-2A1-HH Bedienungsanleitung

Tripp Lite

Tripp Lite B127-1A1-CH Bedienungsanleitung

Tripp Lite

Tripp Lite B132-002A-2 Bedienungsanleitung

Tripp Lite

Tripp Lite HDMI B122-000-60 Bedienungsanleitung

Tripp Lite

Tripp Lite B127A-1A1-BHBH Bedienungsanleitung

Tripp Lite

Tripp Lite B136-101 Bedienungsanleitung

Tripp Lite

Tripp Lite B126-004 Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung

SECO-LARM

SECO-LARM ENFORCER EVT-PB1-V1TGQ Bedienungsanleitung