Tripp Lite PDUMVR20NET Bedienungsanleitung

Warranty

Registration:

chance to win a FREE Tripp Lite

product—www.tripplite.com/warranty

Owner’s Manual

Single-Phase 0U Switched

Power Distribution Units with

Individual Outlet Current Metering

PDUMVR20NET • PDUMVR30NET • PDUMVR30HVNET

(AG-0044) (AG-0045) (AG-0046)

Important Safety Insructions 2

Installation 3

Digital Load Meter 8

Features 9

Conﬁguration and Operation 11

Service 11

Warranty and Warranty Registration 12

Español 13

Français 25

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

201207109-93-3161.indb 1 8/14/2012 2:03:40 PM

Important Safety Instructions

SAVE THESE INSTRUCTIONS

This manual contains instructions and warnings that should be followed during

the installation, operation, and storage of this product. Failure to heed these

instructions and warnings may affect the product warranty.

• Provideadequateprotectionagainstexcesscurrents,shortcircuitsandgroundfaultsin

accordancewithlocalandnationalelectricalcodes,suchasNECintheU.S.

• ThemainssocketoutletthatsuppliesthePDUshouldbenearthePDUandeasilyaccessible.

• OperatethePDUatindoortemperaturesbetween32°Fand104°F(between0°Cand40°C)

only.

• Neverattempttoinstallelectricalequipmentduringathunderstorm

•ThePDUprovidesconvenientmultipleoutlets,butitDOESNOTprovidesurgeorlinenoise

protectionforconnectedequipment.

•ThePDUisdesignedforindooruseonlyinacontrolledenvironmentawayfromexcess

moisture,temperatureextremes,conductivecontaminants,dustordirectsunlight.

•DonotconnectthePDUtoanungroundedoutletortoextensioncordsoradaptersthat

eliminate the connection to ground.

•ThepowerrequirementforeachpieceofequipmentconnectedtothePDUmustnotexceed

the individual outlet’s load rating.

•ThetotalpowerrequirementforequipmentconnectedtothePDUmustnotexceedthe

maximumloadratingforthePDU.

•DonotdrillintoorattempttoopenanypartofthePDUhousing.Therearenouser-serviceable

parts inside.

•DonotattempttomodifythePDU,includingtheinputplugsandpowercables.

•DonotattempttousethePDUifanypartofitbecomesdamaged.

•DonotattempttomountthePDUtoaninsecureorunstablesurface.

•Useofthisequipmentinlifesupportapplicationswherefailureofthisequipmentcan

reasonablybeexpectedtocausethefailureofthelifesupportequipmentortosignicantly

affectitssafetyoreffectivenessisnotrecommended.Donotusethisequipmentinthe

presenceofaammableanestheticmixturewithair,oxygenornitrousoxide.

201207109-93-3161.indb 2 8/14/2012 2:03:40 PM

1-2

1-1

1-3 1-4

Installation

Mounting the PDU

Note: The illustrations may differ somewhat from your PDU model. Regardless of conﬁguration, the user must

determine the ﬁtness of hardware and procedures before mounting. The PDU and included hardware are designed

for common rack and rack enclosure types and may not be appropriate for all applications. Exact mounting

conﬁgurations may vary. Screws for attaching the mounting brackets and cord retention shelf to the PDU are

included. Use only the screws supplied by the manufacturer, or their exact equivalent.

IfinstallingthePDUinarackthathasbutton-mountslots,youonlyneedtoperformstepsfor

toollessmounting(step1-1 ).Ifyourrackdoesnothavebutton-mountslots,proceedtostep1-2 .

Toolless Mounting

1-1  Attachtheincludedmountingbuttons

tothePDU.PositionthePDUasdesired

intherackenclosure,alignthebuttons

withtherackmountingslots,andslide

thePDUintoposition.

Note: To install the PDU with its outlets facing the rear

of the rack, use the included PDUMVROTATEBRKT

accessory. This V-shaped bracket provides a mounting

button on one leg of the V and a button- mount slot on

the other, effectively repositioning the mounting buttons.

See Features section for image.

Regular Mounting

1-2  Attachthemountingbracketstothe

PDU.

1-3  (Optional)Attachthecordretention

bracket(s)tothePDU.

1-4  AttachthePDUtoaverticalrailin

yourrackorrackenclosure.(Usethe

mounting hardware that came with your

rackorrackenclosuretoattachthe

mountingbracketstotherail.) PDUMVR30HVNETShown

201207109-93-3161.indb 3 8/14/2012 2:03:43 PM

Connecting the PDU

2-1 Connect the input plug to your facility’s

compatibleACpowersource.

2-2  Allmodelscontain2banksofoutput

receptacles.

• PDUMVR20NETandPDUMVR30NET

contain2banksof125-15/20R

receptacles(24total).

• PDUMVR30HVNETcontains2banks

of10C13and2C19receptacles

(24total).

 Connectyourequipment’sinputplugs

totheappropriateoutletsonthePDU.

OntheSwitchedmodels,theLEDnear

each outlet illuminates when the outlet

isreadytodistributeliveACpower.

Note: It is recommended that you do not

connect a live load to the PDU. If the load

you intend to connect has an ON/OFF

switch, please turn the switch to OFF prior to

connection.

2-3  (Optional)Ifyouattachedthecord

retentionbracket(s),tieeachequipment

powercordtotheretentionbracket.

Attach each cord to the retention shelf

byloopingthecordandsecuringitwith

oneoftheincludedcableties A.Make

sureeachcordcanbeunpluggedfrom

thePDUwithoutremovingthecabletie.

Installation

Networking the PDU

Note: The MAC address of the PDU (a 12-digit string in this format: 000667xxxxxx) is printed on a label

attached to the PDU enclosure.

Ifyournetwork’sDHCPserverwillassignadynamicIPaddresstothePDUautomatically,go

toStep3-1 .IfyouwillassignastaticIPaddresstothePDUmanually,gotoStep4-1 . If you

areuncertainwhichmethodtouse,contactyournetworkadministratorforassistancebefore

continuing the installation process.

Dynamic IP Address Assignment

3-1 Connect PDU to Network: While the

PDUispowered,connectastandard

EthernetpatchcabletotheRJ-45

EthernetportonthePDU.

Note: This port is not compatible with PoE

(Power over Ethernet) applications. The PDU

will attempt to obtain an IP address via DHCP.

This may take as long as several minutes,

depending on your network environment.

SomeModelsWillVary.

PDUMVR30HVNETShown

201207109-93-3161.indb 4 8/14/2012 2:03:46 PM

242322212019181716151413

CONFIGACCY STATUS

LINK

RESET

ENVIROSENSE

121110987654321

Installation

Dynamic IP Address Assignment

3-2 Discover IP Address: ContactyournetworkadministratortodeterminewhichdynamicIP

addresshasbeenassignedtothePDUbytheDHCPserver.ThePDUcanbeidentiedon

theDHCPserverbyreferringtoitsMACaddress.(TheMACaddressisa12-digitstringin

thisformat:000667xxxxxx.RefertotheMACaddresslabelattachedtothePDU.)Youmay

wishtorequestalong-termleaseperiodfortheIPaddress,dependingonyourapplication.

AfteryouhavediscoveredtheIPaddress,skipSteps4-1 through 4-6 and proceed directly

toStep5-1 .

3-3 Alternate Method:PressandholdtheSelectOutletbuttonontheDigitalLoadMeter

(seepage8)for4secondstodisplaytheIPaddress.Thedefaultisnoaddressassigned.

Ifthisisthecase,“noaddress”willdisplayoneletteratatime.IfthereisanIPAddress

programmed,theaddresswilldisplay1digitatatimewithdashes(-)representingdotsor

periods(.).

Static IP Address Assignment

4-1 Determine IP Information:BeforeassigningastaticIPaddress,you’llneedtoknowthe

IPaddress,gatewayaddressandsubnetmask.Ifyoudonothavethisinformation,contact

yournetworkadministratorforassistance.

4-2 Congure Terminal Emulation Program: OpenaVT100-compatibleterminalemulation

program(suchastheHyperTerminalprogrambundledwithMicrosoft®Windows®)on

acomputerwithanavailableDB9serialport.(Anotebookcomputermaybethemost

convenientchoice.)SettheterminalemulationprogramtousetheCOMportthat

correspondstothecomputer’sDB9serialport.Specifytheparametersrequiredto

communicatewiththePDUterminalinterface:

 Bitspersecond: 9600  Stopbits: 1

Databits:  8  FlowControl: None

Parity:  None

 Iftheterminalemulationprogramsupportsmultipleemulationmodes,youmayalsoneed

tospecifyVT100emulation.

4-3 Connect PDU to Computer: Use

theRJ-45toDB9congurationcable

(partnumber73-1243)includedwith

thePDUtoconnectthePDUtothe

computer. The connector at one end of

thecableattachestotheCONFIGRJ-45

portonthePDU.TheDB9connectorat

theotherendofthecableconnectsto

the computer’s serial port.

4-4 Press SNMP Reset Button: Usinga

smalltoolorpaperclip,pressthereset

buttonfor3secondstorebootthe

PDU’snetworkcard.Rebootingthe

networkcardwillnoterasenetwork

settings or interrupt AC power.

201207109-93-3161.indb 5 8/14/2012 2:03:47 PM

Installation

Static IP Address Assignment

4-5 Congure PDU in Terminal Mode: Afterabriefpause,aninitializationpageshould

appearintheterminalemulationprogram.Pressanykeyonthekeyboardwithin5seconds

tochangethePDUsettings.

Note: If the 5-second period has elapsed, you can reboot the PDU by:

1. Using a small tool or paper clip to press the recessed Reset button on the PDU for 3 second.

2. Pressing any key during, or after, the boot process. This will prompt for a login name and password.

The default user name and password for this process are both “localadmin.” After logging in, type

“reboot” to initiate the card reboot.

Press A to Accept the settings, or M to Modify? M

Enter the root password: *********

Reset conﬁguration and root password to default values. (Y/N)? N

Network Settings

FollowthepromptstocongureIPv4andIPv6addresssettings.Thedefaultterminalmode

passwordisTrippLite.SampleIPsettingsareshown—supplyyourownIPinformationwhenyou

congureyourcard.

ETHERNET INTERFACE SETTINGS:

Obtain IPv4 settings automatically using DHCP for Ethernet interface? [Y]

IP address? [10.1.0.165]

Subnet mask? [255.0.0.0]

Gateway address? [10.0.0.1]

Enable DHCPv6 for the Ethernet interface? [Y]

Enable static IPv6 for the Ethernet interface? [N]

IPv6 address? [2001:DB8::1:58:4F43:4849:544C]

Network preﬁx length? [64]

DNS server? [10.0.0.8]

This card’s host name? [poweralert-061033462177]

This card’s domain? [tlsoftwaredev.local]

201207109-93-3161.indb 6 8/14/2012 2:03:48 PM

Installation

Network Connection

5-1 Connect PDU to Network: While the

PDUispowered,connectastandard

EthernetpatchcabletotheRJ-45

EthernetportonthePDU.

Note: This port is not compatible with PoE

(Power over Ethernet) applications.

5-2 Access PDU with Web Browser: After

anIPaddresshasbeenassignedtothe

PDU,attempttoaccessitwithaWeb

browserthatsupportsframes,forms

andJava™.OpenaWebbrowserona

computerconnectedtotheLANand

entertheIPaddressassignedtothe

PDU.Youshouldbepromptedfora

password A. The user name is admin

and the default password is admin.

After you enter the user name and

password,thePowerAlertstatuspage B

willappearinthebrowserwindow.For

moreinformationaboutconguration

andoperationofthePDUviathe

PowerAlertinterface,refertothe

SNMPWEBCARDUser’sGuide,included

ontheCD-ROMbundledwiththePDU.

Note for Network Management System

Users Only: Two MIB ﬁles - Tripplite.mib

and RFC1628.mib - must be loaded on

each Network Management Station that

will monitor the PDU via SNMP. The ﬁles are

provided on the CD-ROM included in the

product package.

Enable SNTP? [Y]

Enable FTP? [Y]

Port number? [21]

Enable HTTP? [Y]

Port number? [80]

Enable HTTPS? [Y]

Port number? [443]

Enable Telnet Menu? [Y]

Port number? [23]

Enable Telnet Programs? [Y]

Port number? [5214]

Enable SSH Menu? [Y]

Port number? [22]

Enable SSH Programs? [Y]

Port number? [2112]

Enable SNMP? [Y]

Port number? [161]

Enable SNMPv1? [Y]

Enable SNMPv2c? [Y]

Enable SNMPv3? [Y]

Youcanalsochangetherootpassword,real-timeclockandothersettings.(TrippLite

recommends against changing the default settings unless you are an advanced user with a

specicpurpose.)Afteryouhavenishedenteringsettings,thePDUwillsavechangestomemory

andreboot(thismaytakeseveralminutes).AfterthePDUreboots,theinitializationpageshould

displaythenewstaticIPsettings.

4-6 Remove Serial Cable:RemovetheserialcablefromthePDUandproceedtoStep5-1 .

Network Service Conﬁguration

ThefollowingpromptsconguretheconnectionmethodsthattheSNMPWEBCARDwillaccept.

201207109-93-3161.indb 7 8/14/2012 2:03:48 PM

DOWN

Digital Load Meter

1 Select Bank Button:Thisbutton A

canbepressedtoshowtotalcurrentfor

eachbank.Pressingthisbuttononce

will display the total current for all of the

Bank1outlets,locatednearesttothe

inputcord.TheLEDforBank1 Dwill

illuminateandthetotalcurrentforBank

1outletswilldisplayinampsintheLED

Amps display C.Pressingthisbutton

Aa second time will produce the same

resultsforBank2.Pressingthebuttona

thirdtimewilldisplaytotalPDUcurrent

andbothBank1andBank2LEDswill

light.Pressingthebuttonadditional

times will repeat the cycle.

 Ifyoupressandholdthisbuttonfor

4seconds,thenumbersintheLED

Amps display Cwill ﬂip for mounting

versatility.Theunitcanbemountedwith

thepowercordfacingthetoporbottom

whilestillbeingabletoreadthedisplay.

2 Select Outlet Button: Thisbutton Bcanbepressedtoshowthecurrentforeach

individualoutlet.TheLEDlocatednexttotheselectedoutletandtheLEDfortheBank

towhichtheoutletbelongs( Dor E)willashwhenthetotalcurrentforthatoutletis

displayed(inamps)ontheLoadMeterDisplay C.

Pressingthisbuttonasecondtimewillproducethesameresultsforoutlet2,pressinga

thirdtimeforoutlet3andsoonthroughalltheoutlets.

 Ifyoupressandholdthisbutton Bfor4secondsyoucandisplaytheIPAddressassigned

totheunitintheLEDAmpsdisplay C. The default is no address assigned. If this is the

case,“no address”willdisplay,oneletteratatime.IfthereisanIPAddressprogrammed,

theaddresswilldisplay1digitatatimewithdashes(-)representingdotsorperiods(.).

201207109-93-3161.indb 8 8/14/2012 2:03:49 PM

Features

Outlets: Duringnormaloperation,theoutletsdistributeACpowerto

connectedequipment.

Outlet LED: Oncetheunitispowered-on,eachoutletindividuallyramps

upandeachoutletLEDwillilluminatewhentheassociatedoutletisready

todistributeliveACpower.

IEC-60320-C13

IEC-60320-C19 5-15/20R

Circuit Breaker (select models): Eachbankhasitsownbreakerlabeled

Bank1andBank2.Iftheconnectedequipmentloadexceedsthe

MaximumLoadRatingforthatbankofthePDU,thecircuitbreakerwill

trip.

Circuit Breaker (Select Models): Iftheconnectedequipmentload

exceedstheMaximumLoadRatingofthePDU,thecircuitbreakerwill

trip.Disconnectexcessequipmentandallowthebreakertocoolbefore

depressingtheplungertoresetthebreaker.

Cord Retention Bracket:Providessecureattachmentpointsfor

connectedequipmentcords.

Mounting Buttons:Comepre-installedonthebacksideofthePDUand

are used for toolless mounting. Note: Four additional mounting buttons

are included for alternate rack styles.

PDUMVROTATEBRKT Mounting Accessory: UsetheseV-shaped

bracketstomountthePDUwithitsoutletsfacingtherearoftherack.

Ground Screw: Usethistoconnectanyequipmentthatrequiresa

chassis ground.

201207109-93-3161.indb 9 8/14/2012 2:03:56 PM

CONFIG

A B

ACCY

RJ-45 Conguration Port: Usethisporttoprovideadirectterminal

connectiontoacomputerwithaterminalemulationprogram.AnRJ-45

cableisincludedwiththePDU.Ifyouneedareplacementcable,visit

www.tripplite.com for ordering information.

RJ-45 ACCY Port: Reserved for future use.

Ethernet Port: UsethisRJ-45jacktoconnectthePDUtothenetwork

withastandardEthernetpatchcable.TheLinkLED AandStatusLED B

indicateseveraloperatingconditions,asshowninthetablebelow.This

port is not compatible with PoE (Power Over Ethernet) applications.

NetworkOperatingConditions

A Link LED Color

Off NoNetworkConnection

FlashingAmber 100MbpsNetworkConnection

FlashingGreen 10MbpsNetworkConnection

B Status LED Color

Off CardNotInitialized

SteadyorFlashingGreen CardInitializedandOperational

SteadyAmber Error-CardNotInitialized

Features

Mounting Brackets: UsethesebracketstomountthePDU.

SNMP Reset Button: Presstheresetbuttonwithasmalltoolorpaper

clipfor3secondstorebootthePDU’snetworkcard.Rebootingthe

networkcardwillnoterasenetworksettingsorinterruptACpower.

PS/2 Port: UsethisporttoconnectaTrippLiteENVIROSENSE

environmental sensor to provide remote temperature/humidity monitoring

andadrycontactinterfacetocontrolandmonitoralarm,securityand

telecomdevices.Visitwww.tripplite.comfororderinginformation.Note:

Do not connect a keyboard or mouse to this port.

201207109-93-3161.indb 10 8/14/2012 2:03:59 PM

Andere Handbücher für PDUMVR20NET

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Tripp Lite Stromverteilungseinheit Handbücher

Tripp Lite

Tripp Lite PDU3VN10L2120LV Bedienungsanleitung

Tripp Lite

Tripp Lite PDUMH15AT Bedienungsanleitung

Tripp Lite

Tripp Lite PDUMH20HVNET Bedienungsanleitung

Tripp Lite

Tripp Lite PDU3MV6L2130 Bedienungsanleitung

Tripp Lite

Tripp Lite PDU1220T Bedienungsanleitung

Tripp Lite

Tripp Lite PDUMV30-ISO Bedienungsanleitung

Tripp Lite

Tripp Lite PDUMH20NET2 Konfigurationshandbuch

Tripp Lite

Tripp Lite SUDC208V42P60M Bedienungsanleitung

Tripp Lite

Tripp Lite AGPD7897 Series Bedienungsanleitung

Tripp Lite

Tripp Lite Metered Rack PDU Bedienungsanleitung

Tripp Lite

Tripp Lite PDUV30HV Bedienungsanleitung

Tripp Lite

Tripp Lite PDU1220T Bedienungsanleitung

Tripp Lite

Tripp Lite PDUBHV20 Bedienungsanleitung

Tripp Lite

Tripp Lite PDUMVR30NET (AG-0045) Bedienungsanleitung

Tripp Lite

Tripp Lite PDU3VSR10L2130 Bedienungsanleitung

Tripp Lite

Tripp Lite PDUMV20HV Bedienungsanleitung

Tripp Lite

Tripp Lite PDU3V6H50 Bedienungsanleitung

Tripp Lite

Tripp Lite PDUMV15-24 Bedienungsanleitung

Tripp Lite

Tripp Lite PDU10K Bedienungsanleitung

Tripp Lite

Tripp Lite PDUMNV20HV2 Bedienungsanleitung

Tripp Lite

Tripp Lite PDUMH15AT Bedienungsanleitung

Tripp Lite

Tripp Lite PDUMNH20HV Bedienungsanleitung

Tripp Lite

Tripp Lite PDU1420T Bedienungsanleitung

Tripp Lite

Tripp Lite PDU1215 Bedienungsanleitung

Beliebte Stromverteilungseinheit Handbücher anderer Marken

hager

hager SP 015 Bedienungsanleitung

Pakedge

Pakedge PowerPak 9 Bedienungsanleitung

Pts

Pts 9042 Series Bedienungsanleitung

Shure

Shure WA405 Bedienungsanleitung

CORNING

CORNING CCH 4U Bedienungsanleitung

Panamax

Panamax M4LT-EX Bedienungsanleitung

PANCONNECT

PANCONNECT FLAT 3M Bedienungsanleitung

Raytheon

Raytheon 138-118 Bedienungsanleitung

D&R ELECTRONICS

D&R ELECTRONICS PDU-6SS Bedienungsanleitung

Botex

Botex PSA 322-6 DL Bedienungsanleitung

GE QuiXtra 4000 Kurzanleitung

RDL

RDL EZ Series Bedienungsanleitung

StarTech.com

StarTech.com RKPW161915 Systemhandbuch

Vertiv

Vertiv Knürr DI-Strip Rack PDU Bedienungsanleitung

ABB

ABB PSBS0065 Handbuch

Baumuller

Baumuller BFN 3-1-0007-001 Handbuch

Eaton

Eaton StructuredWiringSolutions ESWT41600 Handbuch

GE GEK-45404F Bedienungsanleitung