Tripp Lite SmartRack NEMA 3R Bedienungsanleitung

Owner’s Manual

SmartRack®NEMA 3R

Swinging Wall-Mount Cabinet

General-Use Industrial Control

Models: SRN3RG6US, SRN3RG9US, SRN3RG9USDP,

SRN3RG12US, SRN3RG12USDP

(Series Number: AG-0609)

1111 W. 35th Street, Chicago, IL 60609 USA • tripplite.com/support

WARRANTY REGISTRATION

automatically entered to win an ISOBAR®

surge protector in our monthly drawing!

tripplite.com/warranty

Table of Contents

1. Important Safety Instructions 2

2. Overview 2

3. Feature Identification 3

4. Enclosure Installation 4

4.1 Preparation 4

4.2 Unpacking 4

4.3 Ground Connection 5

5. Enclosure Configuration 5

5.1 Door Locks 5

5.2 Cable Access and Management 5

5.3 Mounting Rails 6

5.4 Adjusting Mounting Rail Depth 6

6. Wall Mounting the Enclosure 7

7. Equipment Installation 10

8. Specifications 10

8.1 Unit Dimensions 10

8.2 Package Dimensions 10

9. Storage and Service 11

10. Warranty and Product Registration 11

Español 12

Francais 23

• The enclosure is extremely heavy. Use caution when handling the enclosure. Do not attempt to unpack, move or install it

unassisted. Use a mechanical device such as a forklift or pallet jack to move the enclosure in the shipping container.

• Do not place any object on the enclosure, especially containers of liquid, and do not attempt to stack the enclosures.

• Inspect the shipping container and the enclosure for shipping damage. Do not use the enclosure if it is damaged.

• Leave the enclosure in the shipping container until it has been moved as close to the ﬁnal installation location as possible.

• Leave adequate space at the front, rear, top and bottom of the enclosure for proper ventilation. Do not block, cover or insert

objects into the external ventilation openings of the enclosure.

• For permanent wall mounting, be sure to securely fasten the enclosure to the building structure before operation.

•

Use caution when cutting packing materials. The enclosure could be scratched, causing damage not covered by the warranty.

• Save all packing materials for later use. Repacking and shipping the enclosure without the original packing materials may

cause product damage that will void the warranty.

• Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause the

failure of the life support equipment or to signiﬁcantly affect its safety or effectiveness is not recommended.

• This enclosure supports a maximum Conduit Trade Size 2 with a 2.5 inch hole.

• Use only NEMA 3R (or higher) rated conduit/ﬁttings to maintain the enclosure’s environmental protection rating.

Swinging wall-mounted NEMA 3R enclosures accommodate all standard 19-inch rack-mount equipment, regardless of vendor,

and ship fully assembled for quick and easy deployment. They have a NEMA 3R rating for protection against falling dirt, rain,

sleet, snow, windblown dust, splashing water and external formation of ice. They feature adaptable, heavy-duty cabinets in various

heights. All models have a hinged design that lets the cabinet swing away from the wall bracket for easy equipment access.

Swinging wall-mounted NEMA 3R enclosures have variable mounting depths, ideal for servers. The cabinets include a lockable,

removable front door and hinged swing cabinet body for convenient maintenance.

1. Important Safety Instructions

2. Overview

SAVE THESE INSTRUCTIONS

This manual contains instructions and warnings that must be followed during the installation and operation of the

product described in this manual. Failure to comply may invalidate the warranty and cause property damage or

personal injury.

3. Feature Identification

Model SRN12G6US is shown. The other models have similar features, with the only differences being rack height and depth.

1Rear Door

2Front Door

3Horizontal Rails

4Vertical Mounting Rails

5Internal Fans

6Removable Cable Access Hole Covers

7Fan Cover Panel

4.1 Preparation

The enclosure must be installed in a structually sound area that is able to bear the weight of the enclosure, all the equipment

that will be installed in the enclosure and any other enclosures and/or equipment that will be installed nearby. Before

unpacking the enclosure, you should transport the shipping container closer to the final installation location to minimize the

distance you will need to move the unit after the protective packaging has been removed. If you plan to store the enclosure for

an extended period before installation, follow the instructions in the Storage and Service section.

4.2 Unpacking

You need several tools:

• Level

• Phillips-head screwdriver

• Appropriate tools for wall mounting

You also need the following hardware:

• Appropriate hardware for wall mounting (not included)

1Move shipping pallet to a firm, level surface.

2Open box and remove the four foam corner protectors. Save all packing materials for later use unless you are certain

they will not be required. Packing materials are recyclable.

3With one person on each side, carefully lift the enclosure out of the box and place on a firm, level surface.

4Examine the enclosure for any damage or loose parts. Confirm all parts are present. If anything is missing or damaged,

contact Tripp Lite for assistance. Do not attempt to use the enclosure if it has been damaged.

4. Enclosure Installation

Caution! Read All Instructions and Warnings Before Installation!

Warning: Rack enclosures can be extremely heavy. Do not attempt to unpack, move or install the enclosure

without assistance. Use extreme caution when handling the enclosure and be sure to follow all handling and

installation instructions. Do not attempt to install equipment without first stabilizing the enclosure.

Use at least two people to unpack the enclosure.

Never extend more than one component from the enclosure at a time.

Warning: Never attempt to lift or install without adequate help.

Do not try lifting the enclosure alone.

4. Enclosure Installation

4.3 Ground Connection

All parts of the enclosure are grounded to the frame of the enclosure.

Use the enclosure’s rear threaded grounding point Aand an M6 hex nut

and washer (included) to connect the frame of the enclosure directly to

your facility’s earth ground connection with an 8 AWG (3.264 mm) wire.

Route the ground wire under the enclosure’s frame to ensure unhindered

door operation. Warning: Attach each enclosure to earth ground

separately. Do not use the enclosure without an earth ground

connection.

EARTH

GROUND

EARTH

GROUND

5. Enclosure Configuration

Before installation, be sure to plan the location and arrangement of components within the enclosure. Be sure all mounting

rails are reversed or adjusted for depth, depending on your equipment configuration.

5.1 Door Locks

The front and rear doors have locks that can be opened with the included keys.

5.2 Cable Access and Management

The enclosure has an opening for cable access and management. The opening

can be closed by screwing in the removable cable access panel.

5. Enclosure Configuration

5.3 Mounting Rails

The enclosure comes with mounting rails that have tapped holes for mounting rack

equipment. To install equipment, use the included hardware. Warning: Be sure to

have the enclosure securely mounted to the wall, or in its final position on

the floor, before mounting any equipment inside. Also be sure to have all

the right adjustments on your rails before mounting equipment. (See below

for Adjusting Mounting Rail Depth.)

5.4 Adjusting Mounting Rail Depth

Warning: Do not attempt to adjust rails while equipment is installed in the enclosure. Do not attempt to use rails

without screws installed. (2 per rail.)

The preset mounting depth varies based on the model. Do not adjust the mounting rails unless your equipment requires a

different mounting depth. The front set of rails can be adjusted independently in 1/2 inch (12.7 mm) increments.

1Each equipment mounting rail is connected to the enclosure with 2 screws: one in the upper corner and another in the

lower corner. Using a Phillips-head screwdriver, remove the screws that fasten the rails to the enclosure.

2Slide the mounting rails to the desired depth and reattach them using the screws you removed in Step 1.

1. Mount the enclosure to wall studs

Warning: Never attempt to lift or install without adequate help.

Do not try lifting the enclosure alone.

Do not attempt to mount the enclosure to the wall with equipment in the enclosure.

The supporting surface must be able to safely support the combined load of the equipment

and all attached hardware and components. For the actual weight, size and load capacity of

the enclosure, view the product specifications and other support resources at

tripplite.com/support.

• Enclosure must be installed by a qualiﬁed technician. Before mounting, use a level and tape measure to position your

mounting area precisely. Use a minimum of four screws (not included, sizes will vary by model) to secure the enclosure in

place. A fender washer with close cell foam is provided with the cabinet. The close cell foam side of the washer should be

against the cabinet to seal the mounting hole.

• Make sure mounting screws are anchored into the center of the studs. Use of a stud ﬁnder is highly recommended.

• If there is no stud at the mounting location, it is recommended you install studs at the desired location to secure the

enclosure in place. Do NOT use plastic expansion wall anchors, threaded drywall anchors, threaded drywall toggles,

sleeve-type hollow wall anchors (a.k.a. molly bolts) or toggle bolts, due to the weight of the enclosure.

• Use suitable mounting means when installing to cinder block, concrete or wood studs. It is the installer’s responsibility to

choose suitable mounting hardware (not supplied). Do NOT use plastic expansion wall anchors, threaded drywall anchors,

threaded drywall toggles, sleeve-type hollow wall anchors (a.k.a. molly bolts) or toggle bolts, due to the weight of the

enclosure.

• If placing the enclosure over a telecommunications receptacle, remove the wall plate, then fasten the enclosure to the

wall. Once secured, fasten the wall plate over the receptacle.

• If no telecommunications receptacle is available, a surface mount box (or biscuit jack) and equipment cord can be

mounted inside the unit.

• Use an adhesive-backed surface mount box.

6. Wall Mounting the Enclosure

ARemove the back door from the enclosure by removing

the nuts securing the hinges to the cabinet body.

6. Wall Mounting the Enclosure

16.00 in.

406.40 mm

21.53 in.

292.77 mm

CAttach the enclosure cabinet

body and front door to the

mounted back door by

mounting the cabinet body

and securing it to the hinges

and nuts removed in Step 1.

Note: Enclosure must be

installed by a qualified

technician. Before mounting,

use a level and tape measure to

position your mounting area

precisely. Use appropriate

fasteners (not included) to

secure the enclosure to the wall.

A minimum of four fasteners is

recommended. A fender washer

with close cell foam is provided

with the cabinet. The close cell

foam side of the washer should

be against the cabinet to seal

the mounting hole. Use suitable

mounting means when installing

to cinder block, concrete,

drywall or wood studs. Warning:

The supporting surface must

be able to safely support the

combined load of the

equipment and all attached

hardware and components.

For the actual weight, size

and load capacity of the

enclosure, view the product

specifications and other

support resources at

tripplite.com/support.

BMount the enclosure's back

door by itself to wall studs.

The number of hole cutouts

on the back door of the

enclosure will vary based on

your model. Each hole can

accommodate an M8, M10,

5/16” or 3/8” bolt. The holes

are centered 16” apart

horizontally to accommodate

the standard placement of

wall studs. The vertical

distance between the holes

will vary based on your

model.

Your model’s hole configuration

may be different.

6. Wall Mounting the Enclosure

2. Use a Drill and Punch (Such as

a Greenlee) to Create a Bottom

Conduit Cutout

3. Run Data and Power Cable (If

Required) Through the Conduit

Cutout

Note: To maintain a NEMA rating, use sealed ﬁttings

in the cutouts when connecting to conduit. Accessory

gland plates with model numbers SRGP1KO, SRGP2KO,

SRGP3RM and SRGP4PLASTIC are available (sold

separately).

Note: This conduit cover supports a maximum Conduit

Trade Size 2 with 2.5” hole.

7. Equipment Installation

Warning: Do not install equipment until you have stabilized the enclosure. Install heavier equipment first and

install it towards the bottom of the enclosure. Install equipment starting from the bottom of the enclosure and

proceeding toward the top of the enclosure—never the reverse. If using sliding equipment rails, be careful when

extending the rails. Do not extend more than one set of sliding equipment rails at one time. Avoid extending

sliding equipment rails near the top of the enclosure.

Note: The tapped holes in the middle of each rack unit are numbered and also include a small notch to aid identification. A single rack

unit includes the space occupied by the numbered hole and the holes directly above and below.

1 Rack Unit

1 RACK UNIT

8. Specifications

8.1 Unit Dimensions

MODEL SRN3RG6US SRN3RG9US SRN3RG9USDP SRN3RG12US SRN3RG12USDP

HEIGHT 17.83 in.

(453 mm)

23.08 in.

(586 mm)

23.25 in.

(591 mm)

28.33 in.

(720 mm)

28.5 in.

(724 mm)

WIDTH 24 in.

(610 mm)

24 in.

(610 mm)

24 in.

(610 mm)

24 in.

(610 mm)

24 in.

(610 mm)

DEPTH 32.08 in.

(815 mm)

32.08 in.

(815 mm)

36.07 in.

(916 mm)

32.08 in.

(815 mm)

36.07 in.

(916 mm)

WEIGHT 116.2 lb.

(52.7 kg)

131.17 lb.

(59.5 kg)

143.27 lb.

(65 kg)

146.44 lb.

(66.4 kg)

159.48 lb.

(72.3 kg)

8.2 Package Dimensions

MODEL SRN3RG6US SRN3RG9US SRN3RG9USDP SRN3RG12US SRN3RG12USDP

HEIGHT 23.5 in.

(597 mm)

27.5 in.

(699 mm)

27.5 in.

(699 mm)

34 in.

(864 mm)

34 in.

(864 mm)

WIDTH 28 in.

(711 mm)

28 in.

(711 mm)

28 in.

(711 mm)

28 in.

(711 mm)

28 in.

(711 mm)

DEPTH 39 in.

(991 mm)

39 in.

(991 mm)

41 in.

(1041 mm)

37 in.

(940 mm)

41 in.

(1041 mm)

WEIGHT 165 lb.

(74.8 kg)

190 lb.

(86.2 kg)

205 lb.

(93 kg)

200 lb.

(90.7 kg)

225 lb.

(102 kg)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Tripp Lite Rack & Stand Handbücher

Tripp Lite

Tripp Lite DMCS60105XXDD Bedienungsanleitung

Tripp Lite

Tripp Lite N062-048-KJ Bedienungsanleitung

Tripp Lite

Tripp Lite SR48UBEXPNDNR3 Bedienungsanleitung

Tripp Lite

Tripp Lite PDU Series Bedienungsanleitung

Tripp Lite

Tripp Lite DWT3270X Bedienungsanleitung

Tripp Lite

Tripp Lite PSCLAMP Bedienungsanleitung

Tripp Lite

Tripp Lite DWM1327SE Bedienungsanleitung

Tripp Lite

Tripp Lite SmartPro AGSM7715 Series Bedienungsanleitung

Tripp Lite

Tripp Lite SR2POSTDP12HD Bedienungsanleitung

Tripp Lite

Tripp Lite DDR811TRAYTAA Bedienungsanleitung

Tripp Lite

Tripp Lite DWM1737MN Bedienungsanleitung

Tripp Lite

Tripp Lite DMCVW4555X4 Bedienungsanleitung

Tripp Lite

Tripp Lite SR4POST25 Bedienungsanleitung

Tripp Lite

Tripp Lite DWF60100XX Bedienungsanleitung

Tripp Lite

Tripp Lite DDR1026SD Bedienungsanleitung

Tripp Lite

Tripp Lite SRWBTLCPLRBR Bedienungsanleitung

Tripp Lite

Tripp Lite SR45UBEXPNDNR3 Bedienungsanleitung

Tripp Lite

Tripp Lite SmartRack Bedienungsanleitung

Tripp Lite

Tripp Lite DDR1732SAL Bedienungsanleitung

Tripp Lite

Tripp Lite DDR1026MQ Bedienungsanleitung

Tripp Lite

Tripp Lite DDR1527SDC Bedienungsanleitung

Tripp Lite

Tripp Lite SRWF12U38 Bedienungsanleitung

Tripp Lite

Tripp Lite DDR1032SE Bedienungsanleitung

Tripp Lite

Tripp Lite DMCSP4560HDS Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung