Tripp Lite B110-SP-CAT-OD2 Bedienungsanleitung

1111 W. 35th Street, Chicago, IL 60609 USA

tripplite.com/support

Quick Start Guide

IP68-Rated Gigabit

PoE Outdoor In-Line

Surge Protector

Model: B110-SP-CAT-OD2

All trademarks are the property of their respective owners.

WARRANTY REGISTRATION

to win an ISOBAR®surge protector in our monthly drawing!

tripplite.com/warranty

Este manual está disponible en español en la página

de Tripp Lite: tripplite.com/support

Ce manuel est disponible en français sur le site Web

de Tripp Lite : tripplite.com/support

Русскоязычная версия настоящего руководства

представлена на веб-сайте компании Tripp Lite

по адресу: tripplite.com/support

Package Includes

• B110-SP-CAT-OD2 Outdoor In-Line Surge Protector

• 18 AWG Grounding Wire – 1 ft.

• Cable Gland, 8.4 mm Diameter (x3)

• Surface Screw Anchors (x4)

• Surface Mounting Screws (x4)

• Unit Cover Screws (x4)

• Owner’s Manual

Product Features

• Protects valuable indoor and outdoor PoE equipment from

power surges, lightning, ESD and cable discharge events in

unforgiving environments

• Complies with 802.3af, 802.3at and 802.3bt IEEE

Standards

• Supports PoE devices up to 90W and Ethernet speeds up

to 1 Gbps

• Meets the following IEC Regulations:

o IEC 61000-4-2 (ESD) +/- 15kV(Air), +/- 8kV(Contact)

o IEC 61000-4-5 (Lightning) 10kA (8/20μs), 20kV

(8/20μs)

• Supports both Mid- and End-Span PoE

• Passive by design – no external power required

Optional Accessories

• N224-Series Cat6 Plenum-Rated Solid-Core Bulk Cable

• N046-000 Punch Down Installation Tool

Figure 1

Mounting Instructions

1. Locate the mounting holes on the bottom of the enclosure,

as shown in Figure 1.

2. Securely mount the bottom portion of the enclosure to the

desired outdoor location. Screw hole diameter supports

mounting screws up to M3.5.

Metric Cable Gland Assembly

Protect indoor and outdoor edge network devices like PoE

cameras or LAN access points from electrical damage by

installing the B110-SP-CAT-OD2 between the source and edge

network equipment.

Notes:

• Maximum cable distance between B110-SP-CAT-OD2 and source

is 328 ft. (100 m).

• Maximum cable distance between B110-SP-CAT-OD2 and

equipment is 328 ft. (100 m).

• For best protection performance, the total cable distance in the

installation should not exceed 328 ft. (100 m).

• The B110-SP-CAT-OD2 must be grounded to function properly.

Installation

Protecting Edge-Of-Network Equipment

This installation protects your edge equipment from surge,

lightning or ESD damage. To protect both the source and edge

equipment, refer to section Protecting Edge-Of-Network

Source and Equipment in this guide.

Note: Use standard size Cat5e, Cat6 or Cat6a cables that feature a

wire gauge of 23/24 AWG. Slim category cables are not supported.

1. Remove both the cap Aand end nut Efrom one of the

cable glands (refer to section Cable Gland Assembly).

2. Slide the cap and remaining portion of the cable gland onto

both the included grounding wire and bare-wire category

cable coming from your source (ex: PoE switch) as shown:

Note: Use standard Cat5e, Cat6 or Cat6a cables with a wire gauge

of 23/24 AWG. Slim category cables are not supported.

Installation

3. Insert both the grounding wire and the bare-wire end of the

category cable in the enclosure, making sure it is inserted

on the “cable end” side.

Installation

4. Screw the metric cable gland to the enclosure using the

end nut Dpreviously removed in step 1. Then, tighten the

cap securely onto the cable gland.

5. Using a punch down tool (such as Tripp Lite’s N046-000,

sold separately), connect the bare wire to the color-coded

board inside the enclosure.

6. Repeat Steps 1-3 for the equipment (ex: PoE camera) side

of the enclosure without the addition of a grounding wire.

Note: To achieve the best protection performance, the Cat5e/6/6a

patch cable between the equipment end of the B110-SP-CAT-OD

surge protector and the equipment to be protected must not exceed

300 ft. (100 m).

Installation

7. Once both bare wires are connected, secure the PCBA

board to the enclosure using the included mounting screws.

Then, attach the grounding wire to the available screw on

the PCBA board.

Note: Make sure you connect your source to the cable end and your

PoE-compliant device to the equipment end.

8. Screw the front cover to the back portion of the enclosure

using the included unit cover screws.

9. The connected PoE device is now protected.

Installation

Protecting Edge-Of-Network Source and

Equipment

The previous installation only protects your edge equipment

from surge, lightning or ESD damage. To protect both the

source and edge equipment, install two B110-SP-CAT-OD2

units in your application. A B110-SP-POE can be installed

instead of a second B110-SP-CAT-OD2 to protect the source if

the second unit will be installed indoors.

Note: Use standard size Cat5e, Cat6 or Cat6a cables that feature a

wire gauge of 23/24 AWG. Slim category cables are not supported.

Maximum cable distance between two B110-SP-CAT-OD2 units is

328 ft. (100 m).

1. Install a second B110-SP-CAT-OD2 between the ﬁrst

B110-SP-CAT-OD2 unit and your source following steps 1-3

in Protecting Edge-Of-Network Equipment section.

Wireless Access Point

B110-SP-CAT-OD2

PoE Switch

To LAN

Installation

2. In order to protect both the source and edge equipment,

the two B110-SP-CAT-OD2 units need to be wired cable-

end to cable-end as shown below.

Equipment End

328 ft.

(100 m)

Andere Handbücher für B110-SP-CAT-OD2

Inhaltsverzeichnis

Andere Tripp Lite Überspannungsschutz Handbücher

Tripp Lite

Tripp Lite TouchMaster (MT-6 Bedienungsanleitung

Tripp Lite

Tripp Lite Isobar Bedienungsanleitung

Tripp Lite

Tripp Lite B110-SP-HDMI Bedienungsanleitung

Tripp Lite

Tripp Lite TSB Handbuch

Tripp Lite

Tripp Lite PS3612-20HW Bedienungsanleitung

Tripp Lite

Tripp Lite Data Shield DNET1 Bedienungsanleitung

Tripp Lite

Tripp Lite TLM626 Bedienungsanleitung

Tripp Lite

Tripp Lite TLM626SA Bedienungsanleitung

Tripp Lite

Tripp Lite TR-6FM Bedienungsanleitung

Tripp Lite

Tripp Lite TLP602 Bedienungsanleitung

Tripp Lite

Tripp Lite TLP808TEL Bedienungsanleitung

Tripp Lite

Tripp Lite AV10IRG Bedienungsanleitung

Tripp Lite

Tripp Lite Data Shield DB25-ALL Bedienungsanleitung

Tripp Lite

Tripp Lite TLM626 Bedienungsanleitung

Tripp Lite

Tripp Lite TLP808 Bedienungsanleitung

Tripp Lite

Tripp Lite TLP2USBD Bedienungsanleitung

Tripp Lite

Tripp Lite SPS415HGULTRA Bedienungsanleitung

Tripp Lite

Tripp Lite DCATV Bedienungsanleitung

Tripp Lite

Tripp Lite SWIVEL6 Bedienungsanleitung

Tripp Lite

Tripp Lite CCIEURO Bedienungsanleitung

Tripp Lite

Tripp Lite TLP725 Bedienungsanleitung

Tripp Lite

Tripp Lite SK6-6 Bedienungsanleitung

Tripp Lite

Tripp Lite SK6-6 Bedienungsanleitung

Tripp Lite

Tripp Lite IBV-12 Bedienungsanleitung

Beliebte Überspannungsschutz Handbücher anderer Marken

ELAC

ELAC ProteK PR91-W Bedienungsanleitung

Tsubaki

Tsubaki TSM4000M1 Bedienungsanleitung

QVS

QVS PP134C Bedienungsanleitung

CyberPower

CyberPower CSP604T Bedienungsanleitung

Davis Instruments

Davis Instruments Radio Surge Protector Bedienungsanleitung

M-system

M-system MGA-100 Bedienungsanleitung

CyberPower

CyberPower CSP706T Bedienungsanleitung

CyberPower

CyberPower B300WRC1 Bedienungsanleitung

M-system

M-system MGD-24 Bedienungsanleitung

Leviton

Leviton 51120-3R Bedienungsanleitung

Panamax

Panamax MAX 5400-EX Bedienungsanleitung

CyberPower

CyberPower B1006T Bedienungsanleitung

OBO Bettermann

OBO Bettermann ÜSM-20-230I1PE65 Bedienungsanleitung

Minuteman

Minuteman MMS7120RCT Bedienungsanleitung

Leviton

Leviton 52412-DS3 Bedienungsanleitung

Savio

Savio LZ-07 Bedienungsanleitung

Siemens

Siemens HNM3M120 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric LITOL LTM-125RF Bedienungsanleitung