Tripp Lite B110-SP-CAT Bedienungsanleitung
1
Quick Start Guide
Digital Signage In-Line
HDBaseT & 10G Network
Surge Protector
Model: B110-SP-CAT
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
Copyright © 2018 Tripp Lite. All rights reserved.
PROTECT YOUR INVESTMENT!
Register your product for quicker service
and ultimate peace of mind.
You could also win an
ISOBAR6ULTRA surge protector—
a $100 value!
www.tripplite.com/warranty
Español 7 • Français 13 • Русский 19
18-10-218-9338D4.indb 1 12/10/2018 6:23:17 PM
2
Package Includes
Product Features
• B110-SP-CAT
• Grounding Wire, 12 in. / 305 mm
• Mounting Screws (x4)
• Screw Anchors (x4)
• Grounding Wire Screw
• Quick Start Guide
• Protects your network equipment’s inputs and outputs against electrostatic
discharge (ESD), lightning surges and cable discharge events
• Meets the following IEC regulations:
o IEC 61000-4-2 (ESD) +/- 15kV (Air), +/- 8kV (Contact)
o IEC 61000-4-5 (Lightning) 2kA (8/20µs), 6kV (8/20µs)
• Surge reaction speed < 1 ns
• Solid-state silicon-avalanche technology
• Supports network data transmission speeds up to 10 Gbps
• Supports resolutions up 4K @ 60 Hz (HDBaseT)
• Easy in-line installation with integrated mounting ears
• Passive by design – no external power required
18-10-218-9338D4.indb 2 12/10/2018 6:23:17 PM
3
Installation
Note: The following instructions assume that two network devices are currently
connected together.
Single Device Protection:
1. Disconnect the installed patch cable from the device you wish to protect
and attach this cable to the “Cable End” of the In-Line HDBaseT & 10G
Network Surge Protector.
2. Using a Cat5/5e/6 patch cable (not included), connect the device to be
protected to the “Equipment End” of the In-Line HDBaseT & 10G Network
Surge Protector.
Note: For best protection performance, the patch cable between the “Equipment
End” of the In-Line HDBaseT & 10G Network Surge Protector and the equipment
to be protected should not exceed 300 ft. (90 m). Tripp Lite’s N001-Series Cat5e
Snagless Patch Cables are recommended.
3. Connect the ground wire to the In-Line HDBaseT & 10G Network Surge
Protector and then to earth ground.
NVR
Equipment End
Network Device
(Protected)
Network Source
(Unprotected)
In-Line HDBaseT
& 10G Network
Surge Protector
Cable End
PC
18-10-218-9338D4.indb 3 12/10/2018 6:23:17 PM
4
Installation
Multiple Device Protection:
Note: The maximum distance between any two In-Line HDBaseT & 10G Network
Surge Protectors is 328 ft. (100 m).
1. Disconnect the installed patch cables from both of the devices you wish to
protect.
2. Connect an In-Line HDBaseT & 10G Network Surge Protector to each end
of the previously uninstalled patch cable, ensuring both ends of the patch
cable are connected to the “Cable End” of the In-Line HDBaseT & 10G
Network Surge Protector.
3. Using Cat5/5e/6 patch cables (not included), connect the “Equipment
End” of each In-Line HDBaseT & 10G Network Surge Protector to the
network devices you wish to protect.
Note: For best protection performance, the Cat5/5e/6 patch cable between the
“Equipment End” of the In-Line HDBaseT & 10G Network Surge Protector and the
network equipment to be protected should not exceed 300 ft. (90 m). Tripp Lite’s
N001-Series Cat5e Snagless Patch Cables are recommended.
4. Connect the ground wire to each In-Line HDBaseT & 10G Network Surge
Protector and then to earth ground.
PC
HDBaseT TX and Source
(Protected)
HDBaseT RX and Device
(Protected)
Equipment End
Cable End
Monitor
HE02ER
Equipment End
Cable End
328 ft. / 100 m
4K @ 60 Hz
18-10-218-9338D4.indb 4 12/10/2018 6:23:17 PM
5
Specifications
Input / Output Connectors RJ45 (Female)
ESD Protection 15kV (Air), 8kV (Contact)
Surge Protection 2kA (8/20µs) / 6kV (8/20µs)
Surge Reaction Speed <1 ns
Operating Temp 14 to 167°F / 10 to 75°C
Storage Temp -40 to 194°F / -40 to 90°C
Bandwidth (Data Rate) Up to 10 Gbps
Return Loss (100Ω) 16 dB
Max Resolution Supported 4K @ 60 Hz
Dimensions 2.63 x 3.43 x 1.06 / 67 x 87 x 27 mm
Weight 0.28 lb. / 127 g
18-10-218-9338D4.indb 5 12/10/2018 6:23:17 PM
6
Warranty and Product Registration
2-Year Limited Warranty
Tripp Lite warrants its products to be free from defects in materials and workmanship for a period
of two (2) years from the date of initial purchase. Tripp Lite’s obligation under this warranty is
limited to repairing or replacing (at its sole option) any such defective products. To obtain service
under this warranty, you must obtain a Returned Material Authorization (RMA) number from
Tripp Lite or an authorized Tripp Lite service center. Products must be returned to Tripp Lite or an
authorized Tripp Lite service center with transportation charges prepaid and must be accompanied
by a brief description of the problem encountered and proof of date and place of purchase. This
warranty does not apply to equipment, which has been damaged by accident, negligence or
misapplication or has been altered or modified in any way.
EXCEPT AS PROVIDED HEREIN, Tripp Lite MAKES NO WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Some states do not permit limitation or exclusion of implied warranties; therefore, the aforesaid
limitation(s) or exclusion(s) may not apply to the purchaser.
EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL Tripp Lite BE LIABLE FOR DIRECT, INDIRECT,
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF THIS
PRODUCT, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Specifically, Tripp Lite is not
liable for any costs, such as lost profits or revenue, loss of equipment, loss of use of equipment,
loss of software, loss of data, costs of substitutes, claims by third parties, or otherwise.
Product Registration
Visit www.tripplite.com/warranty today to register your new Tripp Lite product. You’ll be
automatically entered into a drawing for a chance to win a FREE Tripp Lite product!*
* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.
Use of this equipment in life support applications where failure of this equipment can reasonably
be expected to cause the failure of the life support equipment or to significantly affect its safety
or effectiveness is not recommended.
Tripp Lite has a policy of continuous improvement. Specifications are subject to change without
notice.
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
18-10-218-9338D4.indb 6 12/10/2018 6:23:17 PM
7
Guía de Inicio Rápido
Supresor de
Sobretensiones de Red
HDBaseT y 10G En Línea
Modelo: B110-SP-CAT
1111 W. 35th Street, Chicago, IL 60609 EE UU • www.tripplite.com/support
Copyright © 2018 Tripp Lite. Todos los derechos reservados.
English 1 • Français 13 • Русский 19
18-10-218-9338D4.indb 7 12/10/2018 6:23:17 PM
8
El Paquete Incluye
Características del Producto
• B110-SP-CAT
• Cable de Conexión a Tierra, 30.5 cm [12"]
• Tornillos de Instalación (x4)
• Tornillos de Anclaje (x4)
• Tornillo de Conductor a Tierra
• Guía de Inicio Rápido
• Protege las entradas y salidas de su equipo de red contra descarga
electrostática [ESD], sobretensiones por rayos y eventos de descarga de
cable
• Cumple con los siguientes reglamentos de IEC:
o IEC 61000-4-2 (ESD) +/- 15kV (Aire), +/- 8kV (Contacto)
o IEC 61000-4-5 (Rayo) 2kA (8µs / 20µs), 6kV (8µs / 20µs)
• Velocidad de reacción contra sobretensiones: < 1 ns
• Silicio de estado sólido de Avalanche Technology
• Soporta velocidades de transmisión de datos de red hasta 10 Gbps
• Soporta resoluciones de 4K @ 60 Hz (HDBaseT)
• Fácil instalación en línea con orejas de instalación integradas
• Diseño pasivo – No requiere de alimentación externa
18-10-218-9338D4.indb 8 12/10/2018 6:23:17 PM
9
Instalación
Nota: Las siguientes instrucciones asumen que dos dispositivos de red están
actualmente conectados entre sí.
Protección de un Solo Dispositivo:
1. Desconecte el cable patch instalado del dispositivo que desee proteger y
conecte este cable al “extremo del Cable” del Supresor de Sobretensiones
de Red HDBaseT y 10G En Línea.
2. Utilizando un cable patch Cat5 / Cat5e / Cat6 (no incluido), conecte
el dispositivo a proteger a la “Terminal del Equipo” del equipo en línea
Supresor de Sobretensiones de Red HDBaseT En Línea y 10G.
Nota: Para obtener el mejor rendimiento de protección, el cable patch entre
la “Terminal del Equipo” del Supresor de Supresor de Sobretensiones de Red
HDBaseT y 10G En Línea y el equipo a proteger no debe superar 91 m [300 pies].
Se recomiendan Cables Patch Snagless Cat5e Serie N001 de Tripp Lite
3. Conecte el cable de tierra a cualquier extremo Supresor de Sobretensiones
de Red HDBaseT y 10G En Línea y después a tierra física.
NVR
Terminal del
Equipo
Dispositivo de
Red (Protegido)
Fuente de Red (No
protegida)
Supresor de
Sobretensiones de
Red HDBaseT y 10G
En Línea
Extremo de Cable
PC
18-10-218-9338D4.indb 9 12/10/2018 6:23:17 PM
10
Instalación
Protección de Múltiples Dispositivos:
Nota: La distancia máxima entre dos Supresores de Sobretensiones de Red HDBaseT
y 10G En Línea es de 100 m [328 pies].
1. Desconecte los cables patch instalados de ambos dispositivos que desea
proteger.
2. Conecte un Supresor de Sobretensiones de Red HDBaseT y 10G En Línea
a cada extremo del cable patch desinstalado anteriormente, asegurándose
de que ambos extremos del cable patch están conectados a la “Terminal
del Cable” del Supresor de Sobretensiones de Red HDBaseT En Línea y
10G
3. Usando cables patch Cat5 / Cat5e / Cat6 (no incluidos), conecte la
“Terminal de Equipo” de cada Supresor de Sobretensiones de Red
HDBaseT y 10G En Línea a los dispositivos de red que desee proteger.
Nota: Para mejor rendimiento de protección, el cable patch Cat5 / Cat5e / Cat6
entre la “Terminal de Equipo” del Supresor de Sobretensiones de Red HDBaseT
y 10G En Línea y los equipos de red a proteger no debe superar los 91 m [300
pies]. Se recomiendan Cables Patch Snagless Cat5e Serie N001 de Tripp Lite
4. Conecte el cable de tierra a cada Supresor de Sobretensiones de Red
HDBaseT y 10G En Línea y después a tierra física.
PC
HDBaseT TX y Fuente
(Protegida)
HDBaseT RX y Dispositivo
(Protegido)
Terminal del
Equipo
Extremo de Cable
Monitor
HE02ER
Terminal del
Equipo
Extremo
de Cable
100 m [328 pies]
4K @ 60 Hz
18-10-218-9338D4.indb 10 12/10/2018 6:23:17 PM
Inhaltsverzeichnis
Sprachen:
Andere Tripp Lite Überspannungsschutz Handbücher
Tripp Lite
Tripp Lite IBAR12/20ULTRA AGIB120V20SSRM Bedienungsanleitung
Tripp Lite
Tripp Lite SUPER6TEL12 Bedienungsanleitung
Tripp Lite
Tripp Lite TRAVELERC8 Bedienungsanleitung
Tripp Lite
Tripp Lite isobar HT1210ISOCTR Bedienungsanleitung
Tripp Lite
Tripp Lite Data Shield DNET1 Bedienungsanleitung
Tripp Lite
Tripp Lite ISOTEL4ULTRA Bedienungsanleitung
Tripp Lite
Tripp Lite ISOBAR6DBS Bedienungsanleitung
Tripp Lite
Tripp Lite Protect It! TLM825SA Bedienungsanleitung
Tripp Lite
Tripp Lite Super Series UL1449330 Bedienungsanleitung
Tripp Lite
Tripp Lite ISOTEL8ULTRA Bedienungsanleitung
Tripp Lite
Tripp Lite TR-6FM Bedienungsanleitung
Tripp Lite
Tripp Lite SWIVEL6 Bedienungsanleitung
Tripp Lite
Tripp Lite Protect It! SUPER7TEL15 Bedienungsanleitung
Tripp Lite
Tripp Lite TLP604TEL Bedienungsanleitung
Tripp Lite
Tripp Lite PM6SN1 Bedienungsanleitung
Tripp Lite
Tripp Lite Protect It! TLP310USBC Bedienungsanleitung
Tripp Lite
Tripp Lite B110-SP-CAT-OD2 Bedienungsanleitung
Tripp Lite
Tripp Lite TLP725 Bedienungsanleitung
Tripp Lite
Tripp Lite TLM626TEL15 Bedienungsanleitung
Tripp Lite
Tripp Lite Protect It! 200204173 Bedienungsanleitung
Beliebte Überspannungsschutz Handbücher anderer Marken
OBO Bettermann
OBO Bettermann ÜSM-20-230I1PE65 Bedienungsanleitung
Minuteman
Minuteman MMS7120RCT Bedienungsanleitung
Leviton
Leviton 52412-DS3 Bedienungsanleitung
Savio
Savio LZ-07 Bedienungsanleitung
Siemens
Siemens HNM3M120 Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric LITOL LTM-125RF Bedienungsanleitung