Tripp Lite 0DT60001 Bedienungsanleitung

ssasdfasdfasdf

KVM Extender USB

Quick Start Guide

1111 W. 35th Street, Chicago, IL 60609 USA

www.tripplite.com/support

KVM EXTENDER USB

1. Introduction

The KVM Extender USB system from Minicom is an advanced KVM extender that

performs the following functions:

Extends KVM control over a computer up to a distance of 150m / 500ft

Gives 2 users at 2 workstations control of 1 computer

A 2-port KVM switch at the remote workstation

Full USB keyboard and mouse control

2. System components

The KVM Extender USB system consists of:

Transmitter

Receiver

2 x VGA+USB cable

1 Power adapter for the Receiver

1 Screwdriver

8 non-stick rubber stops

3. The KVM Extender USB units

The figures below illustrate the Transmitter unit.

Figure 1 Transmitter front panel

3.1 Transmitter Button / LEDs

Button / LED Function

Lock button Press to keep control of the connected

computer at the Transmitter position

Control LED Blinks when Transmitter position has control

of the Transmitter position computer

Lock LED Blinks after either Transmitter or Receiver

position presses the Lock button for control

LOCK

MINICOMKVM EXTENDER USB

LOCKCONTROL

Keyboard

USB connector

Mouse USB

connector Lock button

Local + Lock

LEDs

QUICK START GUIDE

Figure 2 Transmitter back panel

The figures below illustrate the Receiver unit. The Receiver can be up to 150m / 500ft

away from the Transmitter.

Figure 3 Receiver front panel

3.2 Receiver Buttons / LEDs

Button / LED Function

Lock button Press to lock control of the Transmitter

computer at the Receiver position

Local button Press to toggle control between the local

Receiver computer and the remote

Transmitter computer (see also section 8.1 on

page 6)

Lock LED Blinks after either Transmitter or Receiver

position presses the Lock button

Local LED Blinks when Receiver position has control of

the Receiver position computer

Figure 4 Receiver back panel

CONTROLPOWER SYSTEM COMPUTER

Power connector Local monitor Computer cable

(Optional)

Control box

System cable

Keyboard

USB connector

Mouse USB

connector

LOCK

MINICOMKVM EXTENDER USB

LOCKLOCAL LOCAL

Lock button

Local button

Local + Lock

LEDs

Power connector

CONTROLPOWER SYSTEM COMPUTEREq

Luminance +

Equalization

selector

(Optional)

Control box

System cable

Local monitor Computer cable

KVM EXTENDER USB

4. Pre-installation instructions

Place cables away from fluorescent lights, air conditioners, and machines that are

likely to generate electrical noise.

5. Connecting the System

When using the system as an extender, extending KVM control from the computer up

to a distance of 150m/500ft, connect the system as in Figure 5. The connections are

explained below.

Figure 5 KVM Extender USB as an extender

5.1 Connecting the Transmitter

Connect a VGA + USB cable - illustrated below - to the Transmitter and a computer.

Connect the HD15 connector to the Transmitter Computer port and connect the VGA

and USB connectors to the local computer Monitor and USB ports.

Figure 6 VGA + USB cable

5.2 Connecting a KVM workstation to the Receiver

Connect a KVM workstation to the Receiver. Connect a keyboard and mouse to the

Receiver Keyboard and Mouse USB ports. Connect a monitor to the Receiver Monitor

port.

Receiver Transmitter

Extended User

position CAT5 cable - 150m/500ft

VGA + USB cable

QUICK START GUIDE

5.3 Connecting the System cable

Connect the System cable CAT5/6/7 FTP cable to the System ports of the Transmitter

and Receiver.

5.4 Connecting to the power supply

The Transmitter receives its power from the connected computer and does not

generally need an external power supply. However, when the Transmitter is connected

to a KVM switch it may need an external power supply. Use a Minicom Power

adapter 12VDC 1A, ordered separately p/n 5PSA70020.

Connect the Receiver to the power supply with the Power adapter and cord provided.

6. Extender system with optional computer at

Receiver position

You can connect a computer to the Receiver position. The Receiver position can then

either control the local computer or the Transmitter position computer.

Figure 7 Extender system with optional computer at Receiver position

The connections are the same as outlined above, with the addition of a

computer connected to the Receiver as follows:

6.1 Connecting a computer to the Receiver

Connect a VGA + USB cable to the Receiver and a computer. Connect the HD15

connector to the Receiver Computer port and connect the VGA and USB connectors

to the computer Monitor and USB ports.

Receiver Transmitter

Local User

position

Extended User

position CAT5 cable - 150m/500ft

Optional PC

KVM EXTENDER USB

7. Extender + KVM switch system with optional

computer at Receiver position

You can connect a KVM switch to the Receiver position. The Receiver position can

then either control the local computer or any computer connected to the KVM switch

at the Transmitter position computer.

Figure 8 Extender + KVM switch with optional computer at Receiver position

The connections are the same as outlined above, with the addition of a KVM

switch connected to the Transmitter as follows:

Connect a VGA + USB cable to the Transmitter and the KVM switch. Connect

the HD15 connector to the Transmitter Computer port and connect the VGA

and USB connectors to the KVM switch Monitor and USB ports.

8. Operating the KVM Extender USB system

The system works on a first come first served basis – press the keyboard or move the

mouse at either the Transmitter (where relevant) or Receiver position to take control

of the Transmitter position computer.

Transmitter position: Press the Lock button to keep/gain control of the computer at

the Transmitter position. The Lock LED at the Transmitter position illuminates and

blinks at the Receiver position. The Control LED at the Transmitter position

illuminates.

Receiver position: Press the Lock button to keep control of the Transmitter computer

at the Receiver position. The Lock LED at the Receiver position illuminates and

blinks at the Transmitter position.

Press the Local button to gain control of the Receiver computer position. The Local

LED blinks.

012345678 1

Receiver Transmitter

Local User

position

KVM Switch

Extended User

position CAT5 cable - 150m/500ft

Optional PC

QUICK START GUIDE

Note! You can only gain control by pressing the Lock button if the Lock LED is

currently not blinking.

Re-pressing the Lock button at either position releases control and the Lock LEDs

turn off.

8.1 Keyboard hotkeys

To toggle between the Transmitter and the Receiver position, press: Caps Lock twice,

release, then press C.

To turn the beeper sound on/off, press: Caps Lock twice, release, then press B.

8.2 Adjusting the picture

At the Receiver, you can adjust the picture quality using a small screwdriver to turn

the Luminance and Equalization Picture adjusters located on the Receiver’s rear

panel.

9. Safety

The device must only be opened by an authorized Minicom technician. Disconnect

device from AC mains before service operation!

9.1 User guide feedback

Your feedback is very important to help us improve our documentation. Please email

any comments to: ug.comments@minicom.com

Please include the following information: Guide name, part number and version

number (as appears on the front cover).

9.2 WEEE compliance

WEEE Information for Minicom Customers and Recyclers

Under the Waste Electrical and Electronic Equipment (WEEE) Directive and

implementing regulations, when customers buy new electrical and electronic

equipment from Minicom they are entitled to:

Send old equipment for recycling on a one-for-one, like-for-like basis (this

varies depending on the country)

Send the new equipment back for recycling when this ultimately becomes

waste

Instructions to both customers and recyclers/treatment facilities wishing to obtain

disassembly information are provided in our website www.minicom.com.

KVM EXTENDER USB

10. Technical specifications

System cable CAT5/6/7 FTP 2x4x24 AWG Solid Wire cable

Maximum distance 150m/500ft

Mouse support USB mouse

Operating systems All major operating systems

Management Push button or external control unit

Screen resolution Up to 1600X1200 @ 75Hz

Operating temperature 0°C to 40°C/32°F to 104°F

Storage temperature -40°C to 40°C/-40°F to 104°F

Warranty 3 Years limited

Transmitter Receiver

Cables & connectors

HDD15F (VGA + USB

cable) – for computer or

KVM switch

HDD15F (VGA + USB cable)

- for optional local computer

USB X 2: for Keyboard +

Mouse USB X 2: for Keyboard +

Mouse

HDD15 : for monitor HDD15 : for monitor

RJ45 - System RJ45 - System

RJ11 - External control unit RJ11 - External control unit

Dimensions 85 x 113 x 25mm/

3.3 x 4.4 x 0.98 inches

85 x 49 x 25mm/

3.3 x 4.4 x 0.98 inches

Shipping weight 1,750g/3.9lb

Power supply From computer or

external power

adapter 12VDC 1A

External power adapter 12VDC 1A

201204190 • 933192_EN

Inhaltsverzeichnis

Andere Tripp Lite Schalten Handbücher

Tripp Lite

Tripp Lite U280-004-OTG Bedienungsanleitung

Tripp Lite

Tripp Lite B004-DUA2-K-R Bedienungsanleitung

Tripp Lite

Tripp Lite U460-003-3AGALC Bedienungsanleitung

Tripp Lite

Tripp Lite B022-016 Bedienungsanleitung

Tripp Lite

Tripp Lite B119-002-UHD Bedienungsanleitung

Tripp Lite

Tripp Lite B127A-4X2-BH2PH Bedienungsanleitung

Tripp Lite

Tripp Lite NGI-M08C4POE8-2 Bedienungsanleitung

Tripp Lite

Tripp Lite B156-004-HD-V3 Bedienungsanleitung

Tripp Lite

Tripp Lite B032-VU2 Bedienungsanleitung

Tripp Lite

Tripp Lite N052-P24 Bedienungsanleitung

Tripp Lite

Tripp Lite B022-002-KT-R Bedienungsanleitung

Tripp Lite

Tripp Lite B006-004-R Bedienungsanleitung

Tripp Lite

Tripp Lite B170-002-R Bedienungsanleitung

Tripp Lite

Tripp Lite B032-HUA2 Bedienungsanleitung

Tripp Lite

Tripp Lite U460-003-3AG Bedienungsanleitung

Tripp Lite

Tripp Lite U360-003-KM Bedienungsanleitung

Tripp Lite

Tripp Lite B020-U08-19-IP Bedienungsanleitung

Tripp Lite

Tripp Lite NetController B042-004 Bedienungsanleitung

Tripp Lite

Tripp Lite U215-004-R Bedienungsanleitung

Tripp Lite

Tripp Lite B005-HUA2-K Bedienungsanleitung

Tripp Lite

Tripp Lite N050-P12 Bedienungsanleitung

Tripp Lite

Tripp Lite B005-DPUA2-K Bedienungsanleitung

Tripp Lite

Tripp Lite B004-2DUA2-K Bedienungsanleitung

Tripp Lite

Tripp Lite B005-DPUA4 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung