Tripp Lite PDUMH30ATNET Bedienungsanleitung
Single-Phase Auto Transfer Switch / Switched PDU,
2.9kW 30A 120V, 2U Horizontal mount, 24 5-15/20R
& 1 L5-30R outlets, 2 L5-30P inputs
MODEL NUMBER: PDUMH30ATNET
Description
Tripp Lite Switched ATS / Auto Transfer Switch provides a redundant power option for single-corded network
devices. Dual input cords support separate connection to PRIMARY and SECONDARY power sources. The
ATS will normally maintain continuous output to all outlets as derived from the primary input cable. If the primary
power source becomes unstable or fails altogether, the ATS will switch over to the secondary power source until
the primary input is restored and stable. Highly reliable solid-state switching between primary and secondary
inputs occurs in 1-5 milliseconds. Switched PDU features include individually controllable output receptacles and
built-in network interface. Super-fast switchover between primary and secondary power sources occurs within
milliseconds. ATS functionality is supported by any two compatible AC power sources, regardless of phase
angle, to support a variety of advanced redundant power networking applications. Enables fault tolerant
hot-swappable UPS protection when used with a single UPS and fully redundant UPS protection when each cord is connected to a separate UPS system. In a
two-UPS environment, the primary input cable must be supported by a full time sine wave UPS with zero transfer time. Tripp Lite SmartOnline series is highly
recommended for use as the primary UPS in a two-UPS application. ATS configurations utilizing separate mains circuits, backup generators and even
separate utility power grid feeds are fully supported. On-board ATS processor constantly evaluates power quality on both input sources to prevent transfer to
the secondary source when unavailable or of lower quality than the primary source. Front input LED's display primary or secondary power availability.
Features
120V 30A Power Distribution Unit (PDU) with Auto-Transfer Switch (ATS) and Switched output receptacles (agency derated to 24A continuous)
ATS features provide redundant power for critical network equipment with a single input power cord
Switched PDU features enable programmable or real-time power control of individual outlets via built-in network interface
Visual meter reports output amp and kW power consumption, plus voltage and temperature/humidity data with optional ENVIROSENSE sensor
25 switched outlets (24 5-15/20R & 1 L5-30R); 2U horizontal rackmount form factor; 11.9 in. / 30.2cm depth
Two NEMA L5-30P 10 ft. / 3m inputs connect to separate PRIMARY and SECONDARY power sources
ATS normally maintains output sourced from the primary input; As primary input power fails or becomes unstable, the ATS switches to power equipment
from the secondary input until power on the primary input is restored
Highlights
Single phase 30A 120V Auto
Transfer Switch / ATS PDU with
Solid State Switching
Enables redundant-power option
for single-corded network devices
Separate primary & secondary
inputs connect to any two
compatible power sources
2U rackmount, 2 L5-30P inputs,
25 switched outlets (24 5-15/20R,
1 L5-30R)
Individually switched outlets,
network interface and visual
current, voltage and
environmental monitoring
Applications
ATS PDU systems provide a
redundant power option with
individual outlet control for
single-corded network devices
Package Includes
PDU with attached L5-30P input
power cords
Installable 2U mounting brackets
User manuals with warranty
information
1 / 4
Highly reliable solid-state switching enables fast 1-5 millisecond trasfer between primary and secondary inputs
ATS configurations enable hot-swap UPS protection when used with a single UPS and redundant UPS protection when each input is connected to a
separate UPS system (in a two-UPS environment, the primary input cable must be supported by an online UPS similar to Tripp Lite SmartOnline)
Advanced ATS configurations using separate mains circuits, backup generators and out of phase utility feeds are fully supported
On-board processor evaluates power quality on both inputs to prevent transfer to the secondary source when unavailable or of lower quality than the
primary source
3-6 millisecond transfer time between primary and secondary inputs
DHCP/Manual configuration support; Supports HTTP, HTTPS, PowerAlert Network Management System, SMTP, SNMPv1, SNMPv2, Telnet, SSH, FTP,
DHCP, BOOTP, NTP protocols
Compatible with optional ENVIROSENSE temperature monitor
Front panel LEDs confirm power availability on primary / secondary inputs and each output receptacle
TAA Compliant Version Available - Order Tripp Lite PDUMH30ATNETAA
Specifications
OVERVIEW
PDU Type Auto-Transfer Switch; Switched
OUTPUT
Output Capacity Details 2.9kW (120V input), 3.0kW (127V input), 2.4kW (100V input); 30A maximum (agency de-rated to 24A continuous)
Frequency compatibility 60 Hz
Output nominal voltage 100-127V nominal, single phase
Outlet quantity / type 24 5-15/20R (switched), 1 L5-30R (switched)
Outlet Type 5-15R, L5-30R
INPUT
PDU Input Voltage 100; 120; 127
Maximum Input Amps (A) 30
Maximum Input Amps (A) Details Agency de-rated to 24A continuous
Input connection type Two labelled L5-30P inputs support Primary and Secondary input connections
PDU Plug Type NEMA L5-30P
Phase Single-Phase
LEDS ALARMS & SWITCHES
Switches
ENTER and MODE switches toggle the digital display to show output amps and kW in 4 separately metered load
banks (BANK 1: 5-20R outlets #1-12, BANK 2: 5-20R outlets #13-24, BANK 3: L5-30R outlet #25, BANK 4: Total
output), input voltage (primary, secondary) and *temperature / humidity data (*with optional
ENVIROSENSE sensor)
Front panel LEDs 25 LEDs display power on/off status for each outlet, plus 2 LEDs for power status on Primary and Secondary input
connection and three additional LEDs to label the displayed numeric value as Amps, kW or Voltage
2 / 4
PHYSICAL
Shipping Dimensions (HWD/in) 8.1 x 20.5 x 17.1
Shipping Dimensions (HWD/cm) 20.6 x 52.1 x 43.4
Shipping weight (lbs) 19.3
Shipping weight (kg) 8.7
Unit Dimensions (HWD/in) 3.4 (2U) x 17.3 x 11.9
Unit Dimensions (HWD/cm) 8.6 (2U) x 43.9 x 43.9
Unit weight (lbs) 15.3
Unit weight (kg) 6.9
Material of construction Steel
Style Rackmount
Form factors supported 2U rackmount
PDU Form Factor Horizontal (1U, 2U, etc)
ENVIRONMENTAL
Relative Humidity Up to 95% (non-condensing)
COMMUNICATIONS
SNMP compatibility Yes, via pre-installled network interface. Provides remote monitoring, outlet control, and automatic power
management configurations.
SPECIAL FEATURES
Appearance Black 2U rackmount steel chassis
CERTIFICATIONS
TAA Compliant Option TAA Compliant Version Available - Order Tripp Lite PDUMH30ATNETAA
Certifications Tested to UL 60950-1 (USA, Canada), Class A (Emissions), NOM (Mexico), RoHS Complaint
WARRANTY
Product Warranty Period (Worldwide) 2-year limited warranty
Related Items
Optional Products
Model Number Description Qty.
WEXT3-PDU-ATNET 3-Year Extended Warranty - For Switched PDUs ending with ATNET 1
WEXT5-PDU-ATNET 5-Year Extended Warranty - For Switched PDUs ending with ATNET 1
3 / 4
ENVIROSENSE Monitors temperature, humidity and contact-closure inputs. (Requires UPS with SNMPWEBCARD,
monitored PDU or switched PDU.) 1
SRSWITCH Magnetic Door Switch Kit for front and rear doors; requires ENVIROSENSE 1
P007-002 2-ft. Heavy-Duty 14AWG Power cord (IEC-320-C13 to NEMA 5-15P) 1
P034-010 10-ft. 14AWG Heavy Duty Power cord ( IEC-320-C19 to NEMA 5-15P) 1
P007-006 6-ft. Heavy-Duty 14AWG Power cord (IEC-320-C13 to NEMA 5-15P) 1
P007-010 10-ft. Heavy-Duty 14AWG Power cord (IEC-320-C13 to NEMA 5-15P) 1
P006-006-13LA 6-ft. 18AWG Power cord (NEMA 5-15P to IEC-320-C13 Left Angle) 1
P006-006-13RA 6-ft. 18AWG Power cord (NEMA 5-15P to IEC-320-C13 Right Angle) 1
P049-010 10-ft. 12AWG Heavy Duty Power cord (IEC-320-C19 to NEMA 5-20P) 1
P044-06I 6-inch 12AWG Heavy Duty Power Adapter cord (NEMA-L5-20R to NEMA-5-20P) 1
More information, including related products, owner's manuals, and additional technical specifications, can be found online at:
http://www.tripplite.com/sku/PDUMH30ATNET.
© 2014 Tripp Lite. All rights reserved. All trademarks are the sole property of their respective owners. Tripp Lite has a policy of continuous improvement.
Specifications are subject to change without notice. Photos may differ slightly from final products.
4 / 4
Inhaltsverzeichnis
Andere Tripp Lite Schalten Handbücher
Tripp Lite
Tripp Lite WEXT5-B072-016 Bedienungsanleitung
Tripp Lite
Tripp Lite U460-004-2A2C Bedienungsanleitung
Tripp Lite
Tripp Lite NetDirector B030-DP08-17D Bedienungsanleitung
Tripp Lite
Tripp Lite B119-003 Bedienungsanleitung
Tripp Lite
Tripp Lite NetDirector B022-U16 Bedienungsanleitung
Tripp Lite
Tripp Lite U444-06N-H4GUC2 Bedienungsanleitung
Tripp Lite
Tripp Lite B302-4HX4H-4K Bedienungsanleitung
Tripp Lite
Tripp Lite B072-032-IP2-K Bedienungsanleitung
Tripp Lite
Tripp Lite NSS-G16D2 Bedienungsanleitung
Tripp Lite
Tripp Lite N252-024-6A-SH Bedienungsanleitung
Tripp Lite
Tripp Lite 108 Bedienungsanleitung
Tripp Lite
Tripp Lite NetCommander B072-008-1 Bedienungsanleitung
Tripp Lite
Tripp Lite U460-004-4AB-C Bedienungsanleitung
Tripp Lite
Tripp Lite C205-004-U-R Bedienungsanleitung
Tripp Lite
Tripp Lite B070-016-19-IP Bedienungsanleitung
Tripp Lite
Tripp Lite NetCommander B070-016-19-IP2 Bedienungsanleitung
Tripp Lite
Tripp Lite B004-VPA2-K-R Bedienungsanleitung
Tripp Lite
Tripp Lite NetDirector B024-HU08 Bedienungsanleitung
Tripp Lite
Tripp Lite U460-003-3AG-C Bedienungsanleitung
Tripp Lite
Tripp Lite U460-002-2AM-C Bedienungsanleitung
