Tripp Lite OMNIVSINT800 Bedienungsanleitung

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

Owner’s Manual

230V Input, Line-Interactive

UPS Systems

(Tower Configuration)

Models: OMNIVSINT800, OMNIVSINT1000,

OMNIVSINT1500XL*

* Extended runtime options

Not suitable for mobile applications.

Important Safety Instructions 2

Quick Installation 3

Basic Operation 5

Storage & Service 8

Español 9

Français 17

Русский 25

18-08-319-932205.indb 1 4/25/2019 5:27:40 PM

Important Safety Instructions

UPS Location Warnings

• Install your UPS indoors, away from excess moisture or heat, dust or direct sunlight.

• For best performance, keep the indoor temperature between between 32º F and 104º F

(0º C and 40º C).

• Leave adequate space around all sides of the UPS for proper ventilation.

UPS Connection Warnings

• Connect your UPS directly to a properly grounded AC power outlet. Do not plug the UPS into

itself; this will damage the UPS.

• Do not modify the UPS’s plug, and do not use an adapter that would eliminate the UPS’s

ground connection.

• Do not use extension cords to connect the UPS to an AC outlet. Your warranty will be voided

if anything other than Tripp Lite surge suppressors are used to connect your UPS to an outlet.

• If the UPS receives power from a motor-powered AC generator, the generator must

provide clean, filtered, computer-grade output.

Equipment Connection Warnings

• Use of this equipment in life support applications where failure of this equipment can

reasonably be expected to cause the failure of the life support equipment or to significantly

affect its safety or effectiveness is not recommended. Do not use this equipment in the

presence of a flammable anesthetic mixture with air, oxygen or nitrous oxide.

• Do not connect surge suppressors or extension cords to the output of your UPS.

Battery Warnings

• Batteries can present a risk of electrical shock and burn from high short-circuit current.

Observe proper precautions. Do not dispose of the batteries in a fire. Do not open the UPS or

batteries. Do not short or bridge the battery terminals with any object. Unplug and turn off the

UPS before performing battery replacement. Use tools with insulated handles. There are no

user-serviceable parts inside the UPS. Battery replacement should be performed only by

authorized service personnel using the same number and type of batteries (Sealed Lead-

Acid). The batteries are recyclable. Refer to your local codes for disposal requirements.

Tripp Lite offers a complete line of UPS System Replacement Battery Cartridges (R.B.C.). Visit

Tripp Lite on the Web at www.tripplite.com/support/battery/index.cfm to locate the specific

replacement battery for your UPS.

SAVE THESE INSTRUCTIONS

This manual contains instructions and warnings that should be followed during the installation,

operation and storage of all Tripp Lite UPS Systems. Failure to heed these warnings will void

your warranty.

18-08-319-932205.indb 2 4/25/2019 5:27:40 PM

Quick Installation

1Unplug the computer’s power cord from

both AC outlet and the computer’s AC

input.

2Insert the female plug of the computer’s

cord into the UPS’s AC input. AInsert the

male plug of the computer's cord into AC

outlet.

Note: After you plug the UPS into a live AC outlet, the

UPS will turn ON automatically. See “ON/OFF” Button

description in the Basic Operation section if you want to

place the UPS in any mode other than ON.

3Using one of the jumper cords supplied

with the UPS, insert the cord’s female

plug into computer’s AC input B. Insert

the cord’s male plug into any of UPS’s

female output receptacles.

4Plug additional equipment into the UPS.*

Use one of the additional jumper cords supplied

with the UPS, or order additional jumper cords

from Tripp Lite. Log on to www.tripplite.com/

support; order part # P004-006.

* Your UPS is designed to support only computer

equipment. You will overload the UPS if the total VA

ratings for all the equipment you connect exceeds the

UPS’s output capacity. To find your equipment's VA ratings,

look on their nameplates. If the equipment is listed in

amps, multiply the number of amps by 230 to determine

VA. (Example: 1 amp × 230 = 230 VA). If you are unsure

if you have overloaded the UPS’s outlets, see “OUTPUT

LOAD LEVEL” LED description.

NORM DELAY

IEC320-C14 plug shown

NORM DELAY

Shown: OMNIVSINT1000

18-08-319-932205.indb 3 4/25/2019 5:27:41 PM

These connections are optional. Your UPS will function properly without these connections.

NORM DELAY

Shown: OMNIVSINT1000

Quick Installation (optional)

1Phone/Network Line Surge Suppression*

Your UPS has jacks which protect against surges

on a phone or network line. Using RJ11 or RJ45

cords, connect your wall jack to the UPS jack

marked IN. Connect your equipment to the UPS

jack marked OUT. Make sure the equipment you

connect to the UPS’s jacks is also protected

against surges on the AC line.

*Not compatible with PoE (Power over Ethernet)

applications.

2USB Communications

Use any USB cable to connect the USB port of

your computer to the USB port of your UPS.

Download the PowerAlert UPS monitoring software

program appropriate for your operating system

from www.tripplite.com and install it on your

computer.

3External Battery Connection

(OMNIVSINT1500XL only)

All UPS models come with a robust internal

battery system; select models feature connectors

that accept an optional external battery pack

(available separately from Tripp Lite) to provide

additional runtime. Adding an external battery will

increase recharge time as well as runtime. See

battery pack owner's manual for complete

installation instructions. Make sure cables are

fully inserted into their connectors. Small sparks

may result during battery connection; this is

normal. Do not connect or disconnect battery

pack when the UPS is running on battery power.

18-08-319-932205.indb 4 4/25/2019 5:27:41 PM

Basic Operation

Buttons

ON/OFF Button

• To turn the UPS ON: if utility power is present, the UPS will turn ON

automatically. If utility power is absent, you can “cold-start” the UPS (i.e.:

turn it ON and supply power from its batteries*) by pressing and holding the

ON/OFF button for one second.**

• To turn the UPS OFF: First, unplug the UPS from the wall outlet; then press

and hold the ON/OFF button for one second.** The UPS will be completely

OFF (deactivated).

• To place the UPS in Charge-Only Mode: This mode enables battery

charging, but disables battery backup. WARNING: when the UPS is in this

mode, it will not provide battery backup during a blackout or brownout. This

mode is only recommended for use in areas that experience frequent

blackout/brownout conditions and when connected equipment is not in use.

Press and hold the ON/OFF button for four seconds to place the UPS in this

mode.** Press and hold the ON/OFF button for one second** to take the

UPS out of this mode.

*If fully charged. **The alarm will beep once briefly after the indicated interval has passed

(with the exception of a continuous beep which signals transition to the Charge-Only mode).

MUTE/TEST Button

To Silence (Mute) UPS Alarms: briefly press and release the MUTE/TEST

button.

Note: continuous alarms (warning you to immediately shut down connected equipment)

cannot be silenced.

To Run a Self-Test: with your UPS plugged in and turned ON, press and hold

the MUTE/TEST button for two seconds. Continue holding the button until the

alarm beeps several times and the UPS performs a self-test. See “Results of a

Self-Test” below. Note: you can leave connected equipment on during a self-

test. Your UPS, however, will not perform a self-test if you have placed it in

“Charge-Only” mode (see “ON/OFF” Button description).

CAUTION! Do not unplug your UPS to test its batteries. This will remove

safe electrical grounding and may introduce a damaging surge into your

network connections.

Results of a Self-Test: The test will last approximately 10 seconds as the

UPS switches to battery to test its load capacity and charge. All LEDs will be lit

and the UPS alarm will sound.

• If the “OVERLOAD” LED remains lit and the alarm continues to sound after

the test, the battery-supported outlets are overloaded. To clear the overload,

unplug some of your equipment from the battery- supported outlets and run

the self-test repeatedly until the “OVER- LOAD” LED is no longer lit and the

alarm is no longer sounding.

CAUTION! Any overload that is not corrected by the user immediately

following a self-test may cause the UPS to shut down and cease

supplying output power in the event of a blackout or brownout.

• If the REPLACE BATTERY LED remains lit and the alarm continues to sound

after the test, the UPS batteries need to be recharged or replaced. Allow the

UPS to recharge continuously for 2-4 hours, and repeat the self-test. If the

LED continues to flash, contact Tripp Lite for service. If your UPS requires

battery replacement, visit www.tripplite.com/support/battery/index.cfm to

locate the specific Tripp Lite replacement battery for your UPS.

18-08-319-932205.indb 5 4/25/2019 5:27:41 PM

Basic Operation

AC Outlets: The Aoutlets will provide battery backup and surge

protection; plug your computer, monitor, printer and other critical devices

here. Your UPS is designed to only support computer equipment. You will

overload the UPS if the total VA ratings for all the equipment you connect to

the Aoutlets exceeds the UPS’s output capacity. If you are unsure if you

have overloaded the Aoutlets, run a self-test (see MUTE/TEST Button

description).

NORM DELAY

Shown:

OMNIVSINT1000

Indicator Lights

All Indicator Light descriptions apply when the UPS is plugged into an AC outlet and turned on.

LINE POWER LED: this green LED lights continuously to indicate that the UPS

is ON and supplying your equipment with AC power from a utility source. The

LED flashes to remind you that you have used the ON/OFF button to place the

UPS in Charge-Only mode.

BATTERY POWER LED: this yellow LED flashes and an alarm sounds

(4 short beeps followed by a pause) to indicate the UPS is operating from its

internal batteries. During a prolonged brownout or blackout, this LED and the

REPLACE BATTERY LED will light continuously and an alarm will sound

continuously to indicate the UPS’s batteries are nearly out of power; you

should save files and shut down your equipment immediately.

REPLACE BATTERY LED: this red LED lights continuously and an alarm

sounds after a self-test to indicate the UPS batteries need to be recharged or

replaced. Allow the UPS to recharge continuously for at least 4 hours, and

repeat the self-test. If the LED continues to flash, contact Tripp Lite for service.

If your UPS requires battery replacement, visit www.tripplite.com/support/

battery/index.cfm to locate the specific Tripp Lite replacement battery for your

UPS.

OVERLOAD LED: this red LED lights continuously and an alarm sounds after a

self-test to indicate the battery-supported outlets are overloaded. To clear the

overload, unplug some of your equipment from the battery-supported outlets

and run the self-test repeatedly until the LED is no longer lit and the alarm is

no longer sounding.

CAUTION! Any overload that is not corrected by the user immediately

following a self-test may cause the UPS to shut down and cease

supplying output power in the event of a blackout or brownout.

VOLTAGE CORRECTION LED (select models only): Lights green whenever

your UPS is automatically correcting high or low AC line voltage. The UPS will

also click gently. These are normal, automatic operations of your UPS, and no

action is required on your part.

Other UPS Features

18-08-319-932205.indb 6 4/25/2019 5:27:42 PM

Basic Operation

NORM DELAY

Telephone or Network Protection Jacks (select models): These jacks

protect your equipment against surges over a telephone or data line.

Connecting your equipment to these jacks is optional. Your UPS will work

properly without this connection. Not compatible with PoE (Power over

Ethernet) applications.

External Battery Pack Connection (select models): Ensure that the

external batteries you are connecting match the voltage listed on your

UPS’s battery connector. Plug the battery connection cable (attached to the

battery pack) into the UPS’s External Battery Connector. Your UPS has

internal batteries; external batteries are only needed to extend runtime.

Adding external batteries will increase recharge time as well as runtime.

Make sure that the end of the cable is fully inserted into the UPS

connector. Several small sparks may result during battery connection; this is

normal.

USB Port: This port can connect your UPS to any computer for automatic

file saves and unattended shutdown in the event of a power failure. Use

with Tripp Lite’s PowerAlert Software and appropriate USB cable. A

PowerAlert CD and USB cable may be included with your UPS; if so, insert

the CD into the CD tray of your computer and follow the installation

instructions. If PowerAlert Software and the appropriate cable did not come

with your UPS, you can download the software FREE via the Web at www.

tripplite.com. Any user-supplied USB cable may then be used to connect

the UPS to your computer.

Note: This connection is optional. The UPS will work properly without this connection.

Battery Replacement Door: Under normal conditions, the original battery

in your UPS will last several years. Battery replacement should be

performed only by qualified service personnel. Refer to “Battery Warnings”

in the Safety section. Should your UPS require battery replacement, visit

Tripp Lite on the Web at www.tripplite.com/support/battery/index.cfm to

locate the specific replacement battery for your UPS.

Power Sensitivity Adjustment: This dial is normally set fully

counterclockwise, enabling the UPS to provide maximum protection against

waveform distortions in its AC input. When such distortion occurs, the UPS

will normally switch to providing PWM sine wave power from battery. In

areas with poor utility power or where the UPS’s input power comes from a

backup generator, chronic waveform distortion could cause the UPS to

switch to battery too frequently, draining the battery. You can reduce how

often your UPS switches to battery due to moderate waveform distortion by

experimenting with different settings for this dial. As the dial is turned

clockwise, the UPS becomes more tolerant of variations in input power AC

waveform.

Note: The further the dial is adjusted clockwise, the more waveform distortion the UPS

will pass to connected equipment. When experimenting with different settings for this

dial, operate connected equipment in a safe test mode so that the effect on the

equipment of any waveform distortions in the UPS’s output can be evaluated without

disrupting critical operations.

DELAY

NORM

18-08-319-932205.indb 7 4/25/2019 5:27:42 PM

Storage & Service

Storage

All connected equipment should be turned off, then disconnected from the UPS to avoid battery

drain. Unplug the UPS from the wall outlet; then press and hold the ON/OFF button for one

second. The UPS will be completely “OFF” (deactivated). Your UPS is now ready for storage. If

you plan on storing your UPS for an extended period of time, fully recharge the UPS batteries

once every three months by plugging the UPS into a live AC outlet and letting the UPS charge

for up to 4 hours. If you leave your UPS batteries discharged for an extended period of time,

they will suffer a permanent loss of capacity.

Service

Your Tripp Lite product is covered by the warranty described in this manual. A variety of Extended

Warranty and On-Site Service Programs are also available from Tripp Lite. For more information

on service, visit www.tripplite.com/support. Before returning your product for service, follow these

steps:

1. Review the installation and operation procedures in this manual to insure that the service

problem does not originate from a misreading of the instructions.

2. If the problem continues, do not contact or return the product to the dealer. Instead, visit

www.tripplite.com/support.

3. If the problem requires service, visit www.tripplite.com/support and click the Product Returns

link. From here you can request a Returned Material Authorization (RMA) number, which is

required for service. This simple on-line form will ask for your unit’s model and serial numbers,

along with other general purchaser information. The RMA number, along with shipping

instructions will be emailed to you. Any damages (direct, indirect, special or consequential) to

the product incurred during shipment to Tripp Lite or an authorized Tripp Lite service center is

not covered under warranty. Products shipped to Tripp Lite or an authorized Tripp Lite service

center must have transportation charges prepaid. Mark the RMA number on the outside of

the package. If the product is within its warranty period, enclose a copy of your sales receipt.

Return the product for service using an insured carrier to the address given to you when you

request the RMA.

Regulatory Compliance Identification Numbers

For the purpose of regulatory compliance certifications and identification, your Tripp Lite product has been assigned a unique

series number. The series number can be found on the product nameplate label, along with all required approval markings and

information. When requesting compliance information for this product, always refer to the series number. The series number

should not be confused with the marking name or model number of the product.

WEEE Compliance Information for Tripp Lite Customers and Recyclers (European Union)

Under the Waste Electrical and Electronic Equipment (WEEE) Directive and implementing regulations, when customers buy

new electrical and electronic equipment from Tripp Lite they are entitled to:

• Send old equipment for recycling on a one-for-one, like-for-like basis (this varies by country)

• Send the new equipment back for recycling when this ultimately becomes waste

Tripp Lite follows a policy of continuous improvement. Specifications are subject to change without notice.

Note on Labeling

Two symbols are used on the label.

V~ : AC Voltage

V: DC Voltage

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

18-08-319 93-2205_revC

18-08-319-932205.indb 8 4/25/2019 5:27:43 PM

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

Manual del propietario

Sistemas UPS interactivos

con la línea, 230 V

de entrada

(Para montaje en torre)

Modelos: OMNIVSINT800, OMNIVSINT1000,

OMNIVSINT1500XL*

* Opción de tiempo de respaldo extendido

No conveniente para los usos móviles.

Instrucciones de seguridad importantes 10

Instalación rápida 11

Operación básica 13

Almacenamiento y Servicio 16

English 1

Français 17

Русский 25

18-08-319-932205.indb 9 4/25/2019 5:27:43 PM

Instrucciones de seguridad importantes

Advertencias sobre la ubicación del UPS

• Instale su UPS bajo techo, lejos de la humedad, el calor, el polvo o la luz solar directa.

• Para un mejor funcionamiento, mantenga la temperatura en ambientes bajo techo entre

32º F y 104º F (0º C y 40º C)

• Deje una cantidad adecuada de espacio alrededor de todos los lados del UPS para una

adecuada ventilación.

Advertencias sobre la conexión del UPS

• Conecte su UPS directamente a una toma de corriente de CA puesta a tierra

apropiadamente. No conecte el UPS a si mismo ya que podría dañarse.

• No modifique el enchufe del UPS ni emplee un adaptador que elimine la conexión a tierra del

UPS.

• El uso de este equipo en aplicaciones de soporte de vida en donde la falla de este equipo

pueda razonablemente hacer suponer que causará fallas en el equipo de soporte de vida o

afecte significativamente su seguridad o efectividad, no está recomendado. No use este

equipo en la presencia de una mezcla anestésica inflamable con aire, oxigeno u óxido

nitroso.

• Si el UPS recibe energía de un generador de CA accionado por motor, el generador debe

proporcionar una salida limpia y filtrada de grado computadora.

Advertencias sobre la conexión de equipos

• No utilice sistemas UPS de Tripp Lite para aplicaciones de soporte de vida en las que un

funcionamiento defectuoso o una anomalía de un UPS Tripp Lite pudiera causar la falla o una

alteración importante en el funcionamiento de un dispositivo de soporte de vida.

• No conecte supresores de sobretensiones ni cordones de extensión a la salida de su UPS.

Esto podría dañar el UPS y anular las garantías del supresor de sobretensiones y del UPS.

Advertencias sobre la batería

• Debido a que las baterías presentan un peligro de choque eléctrico y quemaduras por las

altas corrientes de cortocircuito, tome las precauciones adecuadas. No deseche las baterías

en un incinerador. No abra las baterías. No ponga los terminales de la batería en corto o en

puente con ningún objeto. Apague y desconecte el UPS antes de reemplazar la batería. Sólo

debe cambiar las baterías personal técnico debidamente capacitado. Use herramientas con

mangos aislados y reemplace las baterías existentes con el mismo número y tipo de baterías

nuevas (plomo-ácido selladas). Las baterías del UPS son reciclables. Consulte la

reglamentación local para los requisitos de disposición de desechos. Tripp Lite ofrece una

línea completa de Cartuchos de reemplazo de batería para UPS (R.B.C.). Visite Tripp Lite en

la web en www.tripplite.com/support/battery/index.cfm para localizar la batería de reemplazo

específica para su UPS.

GUARDE ESTAS INSTRUCCIONES

Este manual contiene instrucciones y advertencias que deben seguirse durante la instalación,

operación y el almacenamiento de todos los UPS de Tripp Lite. La no observancia de estas

advertencias anulará su garantía.

18-08-319-932205.indb 10 4/25/2019 5:27:43 PM

Andere Handbücher für OMNIVSINT800

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Tripp Lite UPS Handbücher

Tripp Lite

Tripp Lite AGSM5060 Bedienungsanleitung

Tripp Lite

Tripp Lite VS450T Bedienungsanleitung

Tripp Lite

Tripp Lite OmniSmart & SmartPro USB Bedienungsanleitung

Tripp Lite

Tripp Lite Power Suppy Bedienungsanleitung

Tripp Lite

Tripp Lite SmartPro RMX RMX 1000-2000 VA Bedienungsanleitung

Tripp Lite

Tripp Lite SmartPro SMX1200XLHG Bedienungsanleitung

Tripp Lite

Tripp Lite OmniSmart 725 Bedienungsanleitung

Tripp Lite

Tripp Lite SmartOnline SU3000RTXLCD3U Konfigurationshandbuch

Tripp Lite

Tripp Lite BCPRO850 Konfigurationshandbuch

Tripp Lite

Tripp Lite SmartOnline Intelligent True On-Line UPS... Montage- und Bedienungsanleitung

Tripp Lite

Tripp Lite OmniSmart OMNI1500LCD Bedienungsanleitung

Tripp Lite

Tripp Lite SmartOnline 200703028 Bedienungsanleitung

Tripp Lite

Tripp Lite OMNIVS1500 Bedienungsanleitung

Tripp Lite

Tripp Lite OMNISMT700M Bedienungsanleitung

Tripp Lite

Tripp Lite SmartOnline SU30K3/3 Bedienungsanleitung

Tripp Lite

Tripp Lite SmartOnline 220/380V Bedienungsanleitung

Tripp Lite

Tripp Lite AVRX750UTAA Bedienungsanleitung

Tripp Lite

Tripp Lite BC600SINE Bedienungsanleitung

Tripp Lite

Tripp Lite OmniSmart OMNI300NAFTA Bedienungsanleitung

Tripp Lite

Tripp Lite TE600 Bedienungsanleitung

Tripp Lite

Tripp Lite ECO1000LCD Bedienungsanleitung

Tripp Lite

Tripp Lite SmartOnline SU1500XL Bedienungsanleitung

Tripp Lite

Tripp Lite OmniSmart RMX 500 VA OM500RMX Bedienungsanleitung

Tripp Lite

Tripp Lite SmartPro VS SMART2200VS Bedienungsanleitung

Beliebte UPS Handbücher anderer Marken

Pylontech

Pylontech Victron & Pylontech US5000 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung

Mecer

Mecer ME-1000-WTU Bedienungsanleitung

Mustek

Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch

Emerson

Emerson Liebert NXL series Bedienungsanleitung

MAKELSAN

MAKELSAN BOXER SERIES Bedienungsanleitung

Block

Block PC-0524-400-0 Bedienungsanleitung

CyberPower

CyberPower CP585LCD Bedienungsanleitung

Eaton

Eaton 3S Montageanleitung

CyberPower

CyberPower Office Tower Series UPS 1000 Bedienungsanleitung

CyberPower

CyberPower BM100 Bedienungsanleitung

Best Power

Best Power 610 Bedienungsanleitung

Best Power

Best Power Unity/I UT3K Bedienungsanleitung

Mustek

Mustek PowerMust 400 Offline Bedienungsanleitung

Xantrex

Xantrex Trace 512 UR-UPS Bedienungsanleitung

Forza

Forza SL-1501UL Bedienungsanleitung

LEGRAND

LEGRAND keor 310081 Bedienungsanleitung

ABB

ABB Conceptpower DPA 500 Bedienungsanleitung