Trox Technik CA Bedienungsanleitung
Product overview
1
23
Fig. 1: Schematic representation, CA
1 Casing of the silencer
2 Spigot
3 Lip seal
Important notes
Safety
Correct use
Circular silencers are used to reduce noise in the
circular ducts of ventilation and air conditioning sys-
tems within closed rooms.
For the reduction of air-regenerated noise of air
terminal units and mechanical self-powered control-
lers, etc.
Do not use circular silencers in extract air systems
in commercial kitchens unless the extract air has
been cleaned as much as possible with high-effi-
ciency aerosol separators; see VDI 2052.
Use in potentially explosive atmos-
pheres (ATEX)
Circular silencers do not fall under the scope
in accordance with Chapter 1, Article 1, Point
1a, 1b and 1c of EU Directive 2014/34/EU. The
circular silencers must be used in areas with
a potentially explosive atmosphere, zones 1, 2
and zones 21, 22 (outside), in accordance with
Guideline 1999/92/EC.
Please note:
–Max. operating temperature 90 °C
–Max. airflow velocity 20 m/s
–When using lip seals for tube attachment,
a grounding cable must be provided for the
sound attenuator/tube.
–Earth circular silencers!
–Clean sound attenuators regularly to prevent
accumulated dust!
–Clean circular silencers in such a way that
no electrostatic charge builds up!
Manufacturer's statement
Þ
www.troxtechnik.com.
Installation manual GB/en
Circular silencer
CA
TROX GmbH
Heinrich-Trox-Platz
47504 Neukirchen-Vluyn, Ger-
many
Germany
+49 (0) 2845 202-0
+49 (0) 2845 202-265
E-mail: [email protected]
www.troxtechnik.com
A00000071256, 01/2023, © TROX GmbH 2022
Circular silencer CA 1
Incorrect use
WARNING!
Danger of injury or risk of damage to property
due to incorrect use
Incorrect use of the circular silencer can lead to
dangerous situations.
Never use the circular silencer:
–outdoors without sufficient protection against
the effects of weather
– in rooms and systems with aggressive or
contaminated air (to be assessed on a case
to case basis)
– in process air systems
Modifying the unit or using replacement parts that
have not been approved by TROX is not permitted.
Staff
Qualification
The work described in this manual has to be car-
ried out by individuals with the qualification, training,
knowledge and experience described below:
Specialized personnel
Specialised personnel are personnel, who due to
their specialized training, skills, and experience,
as well as knowledge of the applicable standards
and regulations, are capable of executing the tasks
assigned to them, and of recognizing possible haz-
ards and avoiding them on their own.
Personal protective equipment
Personal protective equipment is equipment that
protects the user against health or safety risks at
work.
Personal protective equipment must be worn for
various types of work; the protective equipment
required is listed in this manual together with the
description of each type of work.
Description of personal protective equipment
Industrial safety helmet
Industrial safety helmets protect the head from
falling objects, suspended loads, and the effects of
striking the head against stationary objects.
Protective gloves
Protective gloves protect hands from friction, abra-
sions, punctures, deep cuts, and direct contact with
hot surfaces.
Safety shoes
Safety shoes protect the feet against crushing,
falling parts, and from slipping on slippery ground.
Repair and replacement parts
Only qualified personnel must repair the products,
and they have to use genuine replacement parts.
Transport, storage and packaging
Delivery check
Check delivered items immediately after arrival for
transport damage and completeness. In case of
any damage or an incomplete shipment, contact the
shipping company and your supplier immediately.
Transport, storage and packaging
Circular silencer CA2
Transport on site
Please note:
Be careful when unloading or moving the
product, and pay attention to the symbols and
information on the packaging.
If possible, take the product in its transport
packaging up to the installation location.
Use only lifting and transport gear designed for
the required load.
Always secure the load against tipping and
falling.
Do not move bulky items just by yourself. Get
help to prevent injuries and damage.
Storage
Please note:
Store the product only in its original packaging
Protect the product from the effects of weather
Protect the product from humidity, dust and
contamination
Storage temperature: -30 °C to 90 °C.
Relative humidity: 80 % max., no condensation
Packaging
Properly dispose of packaging material.
Installation
General installation information
Personnel:
Specialized personnel
Protective equipment:
Protective gloves
Industrial safety helmet
Safety shoes
CAUTION!
Danger of injury from sharp edges, sharp cor-
ners and thin sheet metal parts!
Sharp edges, sharp corners and thin sheet metal
parts may cause cuts or grazes.
– Be careful when carrying out any work.
–Wear protective gloves, safety shoes and a
hard hat.
Please note:
Horizontal or vertical installation orientation.
Duct connection on both sides.
Installation in ducts outside closed rooms
requires sufficient protection against the effects
of weather.
Length (L) refers to the airflow direction.
Installation material is not part of the supply
package unless stated otherwise.
Airflow direction freely selectable.
Torsion-free installation.
InstallationOperation
Circular silencer CA 3
Installation information for circular silencer
General information
When designing and constructing ventilation
and air conditioning systems, take into account
the requirements of VDI6022, in particular:
–Hygienic, clean installation of all compo-
nents and their air distribution surfaces
– Inspection and cleaning options by plan-
ning inspection/cleaning openings in the
ducting system
– Avoidance of leaks
Affix the circular silencer proficiently and only
to load-bearing components.
Load suspension systems only with the weight
of the circular silencer. Adjacent components
and connecting ducts must be supported sepa-
rately.
Only use approved and sufficiently dimen-
sioned suspensions for fixing. Secure screw
connections against self-loosening, e.g., by
locking them. Fixing material is not included in
the supply package.
Use only the shortest possible self-tapping
screws in the vicinity of the spigot for fixing
Fig. 2: Installation example for circular silencer
1 Duct
2 Circular silencer
3 Drilling screw for affixing to the ducting
4 Clamp
5 Suspension, e.g., with threaded rod
Fig. 3: Examples of fixings for rounded units
1 Fixing to pipe clamps
2 Fixing to suspension element
When installing the circular silencer, choose
a load-bearing structure that will support the
entire weight of the circular silencer construc-
tion.
The weight of the circular silencer must not be
supported by the spigots or flanges alone.
Tension-free assembly
Structure-borne sound transmission must be
avoided by taking suitable measures.
Installation in ducts outside closed rooms
requires sufficient protection against the effects
of weather
Take standard DIN EN 12236 into considera-
tion (suspensions and supports for air ducts)
Flange constructions
Flange constructions are designed according to DIN
EN 12220. Connection dimensions of the flanges
can be found in the standard.
Assembly to control components
Circular silencers without splitters can be used for
the reduction of air-regenerated noise of air terminal
units and mechanical self-powered controllers. The
installation takes place immediately downstream of
the control component.
InstallationOperation
Circular silencer CA4
Connecting the duct
When connecting the ducting, the customer must
ensure that the connection points are installed as
air-tight as possible in order to avoid negative influ-
ences from leakages such as air volume deviations,
power consumption, etc. Unless otherwise stated,
the connecting material is not included in the supply
package.
Before connecting the ducting:
Check the inside of the unit for damage and
loose parts.
Remove any contamination from the ducting.
Leakage classes
In order to be able to achieve the required tight-
ness of the duct system, it is necessary that suit-
able sound attenuators and duct components have
been selected. In addition, the following should be
observed:
Proper and expert assembly
Provide seals
Establish the cable fastening (suspension/sup-
port)
Circular ducting – metal
Spigot without lip seal
Plug-in mounting on ducting in accordance with EN 1506 or EN 13180.
Fixing and sealing with ventilation strip, e.g., KLP180.
When using heat-shrinkable tape near the spigot, watch out for plastic
parts of other components and heat carefully.
Spigot with optional lip seal
Plug-in mounting on ducting in accordance with EN 1506 or EN 13180.
Connect the spigot with the ducting, e.g., using drilling screws.
No further sealing required.
Spigot with steel flanges (galvanised steel)
Matching flanges available as accessories
Seal and screw connection M8 (to be provided by others)
Dimensions and number of holes in accordance with EN 12220.
Position the ducting exactly. Do not pull the distances together via the
flange connection.
1
Retrofitting of lip seals
Double lip seal: Fit the short lip (1) on the connection side
Fit the ring seal as shown; avoid excessive stretching.
Check for proper seating in the groove
Apply talcum around the ring seal
InstallationOperation
Circular silencer CA 5
Technical data
General data
Item Value
Nominal sizes 80 - 800 mm
Operating pressure Minimum -750 Pa
2000 Pa max.
Airflow velocity ≤ 20 m/s
Air temperature -30 °C to 90 °C
Relative humidity ≤ 80%, no condensation
Casing leakage according to
EN 15727
Class D (up to and including
nominal size 400)
Class C (from nominal size
450)
* No corrosion resistance according to ISO 12944-2 has been speci-
fied for circular silencers.
Item Value
Materials of circular
silencer*
Galvanised steel
(1.0917)
Stainless steel V2A
(1.4301)
Stainless steel V4A
(1.4571)
* No corrosion resistance according to ISO 12944-2 has been speci-
fied for circular silencers.
Technical data
Circular silencer CA6
Dimensions and weightCA
ØD
ØD₃
ØD₂
L
60 L₁
Dimensions
nominal size ØD CA025 CA050 CA100
ØD2 ØD3 ØD2 ØD3 ØD2 ØD3
80 79 80 129 80 184 284
100 99 100 154 100 204 100 304
125 124 125 184 125 228 125 319
160 159 160 204 160 254 160 354
200 199 200 254 200 304 200 405
250 249 250 354 250 455
315 314 315 405 315 505
400 399 400 505 400 605
450 448 450 636
500 498 500 716
560 558 560 806
630 628 630 806
710 708 710 908
800 798 800 1008
No registration: Spigot with groove according to EN 1506 / ØD
D2 Spigot with lip seal on both sides acc. to EN 1506 / ØD
AS Spigot with lip seal - ØD and socket-type spigot on one end - ØD2
ØD3 outer diameter
Technical data
Circular silencer CA 7
Lengths
Nominal length L L1
[mm]
500 500 380
1000 1000 880
1500 1500 1380
Weights (plain casing)
nominal
size
CA025 CA050 CA100
Nominal length
500 1000 500 1000 1500 500 1000 1500
m [kg]
80 3 4 3 6
100 3 5 4 6 5 9 13
125 3 6 4 7 6 10 14
160 4 7 5 8 7 11 16
200 5 8 6 10 8 13 19
250 7 12 17 9 15 22
315 8 14 21 10 18 25
400 10 18 26 13 23 32
450 24 33
500 28 40
560 45
630 47
710 54
800 62
Commissioning
Commissioning and operation
Personnel:
Specialized personnel
Before you start commissioning:
Check proper installation of the circular
silencers.
Ensure that all sound attenuators are
clean and free from residues and for-
eign matter.
Commissioning
Code of good practice for commis-
sioning
Commissioning is governed by the standard "DIN
EN 12599 Testing and measuring procedures
for the transfer of installed ventilation and air
conditioning systems", and, if applicable, contrac-
tually agreed services between HVAC contrac-
tors, system owners and installation engineers.
The standard describes the essential commis-
sioning steps of the completeness check, func-
tion check, function measurement as well as
report generation and handover.
Commissioning
Circular silencer CA8
Operation
Once commissioning has been completed, the cir-
cular silencer will operate in a self-powered manner
and require no intervention from the system owner.
Depending on the area of application of the circular
silencer, test specifications and intervals may have
to be observed.
Maintenance
System owner's responsibility
WARNING!
Only authorised specialist personnel are
allowed to perform the described mainte-
nance measures.
The system owner is responsible for maintenance.
The system owner is responsible for creating a
maintenance plan, for defining the maintenance
goals, and for the functional reliability of the equip-
ment.
The legal regulations must be observed during
maintenance, e.g. the system owner is responsible
for hygienic operation in accordance with VDI 6022.
Maintenance
The circular silencers are low-maintenance in terms
of wear, but they must be included in the regular
cleaning of the ventilation system. Regular care and
maintenance ensure long service life of the circular
silencer.
Inspection measures
1. Remove contamination that affects the func-
tion of the circular silencer.
2. Check all screws for firm seating and
retighten them, if necessary.
3. Document the maintenance work.
Repair
Repair work is only allowed to be carried out by
specialist personnel or by the manufacturer. Only
genuine replacement parts must be used.
Disposal
ENVIRONMENT!
Risk of harm to the environment due to incor-
rect disposal of goods and packaging!
Incorrect disposal can harm the environment.
– Be sure to comply with the relevant national
guidelines and regulations.
–If you are not sure how to dispose of any-
thing in an environmentally friendly manner,
contact your local authorities or a specialist
disposal company.
Note: The sound attenuator has to be disassem-
bled for disposal.
If no take back (disposal) agreement with
TROX GmbH is in place, we recommend disposing
of the various materials as described below:
1
2
3
Fig. 4: Schematic illustration of the circular silencer
Maintenance
Circular silencer CA 9
No. Part Material/
waste dis-
posal code
Disposal
1 Casing, inner
duct and
spigot
Casing, inner
duct, spigot
and splitter
frame
Galvanised
sheet steel,
stainless
steel EAK
170405
Scrap and
metal recy-
cling
2 Lip seal,
cover fleece
Plastic EAK
170203
According to
EAK
3 Absorption
material
Mineral wool
EAK 170604
According to
EAK
EWC European Waste Catalogue
Maintenance
Circular silencer CA10
Dieses Handbuch passt für folgende Modelle
3
Inhaltsverzeichnis
Andere Trox Technik Lüfter Handbücher
Trox Technik
Trox Technik X-GRILLE Bedienungsanleitung
Trox Technik
Trox Technik VDW-Q Bedienungsanleitung
Trox Technik
Trox Technik VARYCONTROL LVC Leitfaden
Trox Technik
Trox Technik DID-E2 Series Bedienungsanleitung
Trox Technik
Trox Technik SCHOOLAIR-S-HV Bedienungsanleitung
Trox Technik
Trox Technik FKA2-EU Bedienungsanleitung
Trox Technik
Trox Technik Auranor DSO Bedienungsanleitung
Trox Technik
Trox Technik TFM Handbuch
Trox Technik
Trox Technik JZ Series Bedienungsanleitung
Trox Technik
Trox Technik PWX Series Montageanleitung
Trox Technik
Trox Technik UL series Bedienungsanleitung
Trox Technik
Trox Technik AIRNAMIC Series Bedienungsanleitung
Trox Technik
Trox Technik X-GRILLE Bedienungsanleitung
Trox Technik
Trox Technik PURELINE35 Bedienungsanleitung
Trox Technik
Trox Technik FSL-B-ZAB/SEK Bedienungsanleitung
Trox Technik
Trox Technik TSD -3-NF Series Bedienungsanleitung
Trox Technik
Trox Technik TFC Handbuch
Trox Technik
Trox Technik X-GRILLE modular Bedienungsanleitung
Trox Technik
Trox Technik CAK Bedienungsanleitung
Trox Technik
Trox Technik AXO/BVAXO Bedienungsanleitung
