True TGU-2 Bedienungsanleitung

............ www.truemfg.com ............

INSTALLATION MANUAL FOR TGU MODELS

(TRUE GASTRONORM UNDERCOUNTER & WORKTOP

REFRIGERATORS / FREEZERS)

TRUE GASTRONORM

UNDERCOUNTER & WORKTOP

REFRIGERATORS / FREEZERS

CONGRATULATIONS!

You have just purchased the finest commercial

refrigeration available. You can expect many years

of trouble-free operation.

TRUE FOOD SERVICE EQUIPMENT, INC.

2001 East Terra Lane • P.O. Box 970 • O’Fallon, Missouri 63366

(636)-240-2400 • FAX (636)272-2408 • INT’L FAX (636)272-7546 • (800)325-6152

Parts Department (800)424-TRUE • Parts Department FAX# (636)272-9471

TABLE OF CONTENTS

Safety Information

Safety Precautions ––––––––––––––––––––––––1

Proper Disposal –––––––––––––––––––––––––––2

Connecting Electricity ––––––––––––––––––––––3

Adapter Plugs ––––––––––––––––––––––––––––3

Installation / Operation Instructions

Ownership ––––––––––––––––––––––––––––––– 4

Required Tools –––––––––––––––––––––––––––– 4

Uncrating & Locating ––––––––––––––––––––––– 4

Installation of Leg/Castors –––––––––––––––––– 5

Leveling Cabinet –––––––––––––––––––––––––– 6

Electrical Instructions––––––––––––––––––––––– 6

Start-up ––––––––––––––––––––––––––––––––– 7

Shelving Installation - Operation –––––––––––––– 8

Maintenance, Care & Cleaning

Cleaning Condenser Coil –––––––––––––––––––– 9

Stainless Steel Equipment Care & Cleaning –––– 10

TGU-2

TGU-3F

SB #912630

............ www.truemfg.com ............

True Food Service Equipment, Inc.

• This refrigerator must be properly installed

and located in accordance with the Installation

Instructions before it is used.

• Do not allow children to climb, stand or hang

on the shelves in the refrigerator. They could

damage the refrigerator and seriously injure

themselves.

• Do not touch the cold surfaces in the

refrigerated compartment when hands are damp

or wet. Skin may stick to these extremely cold

surfaces.

• Do not store or use flammable liquids or vapors

in the vicinity of this or any other appliance.

• Keep fingers out of the “pinch point” areas;

clearances between the doors and cabinet are

necessarily small; be careful closing doors when

children are in the area.

NOTE: Any servicing, warranty repairs or maintenance

should be carried out by qualified personnel, failure

to do so could be dangerous and may invalidate your

warranty.

• Unplug the refrigerator before cleaning and

making repairs.

• Setting temperature controls to 0 position does

not isolate the unit from the electrical supply,

you must disconnect the main power lead from

the wall receptacle to isolate.

WARNING!

Use this appliance for its intended purpose as described in this Owner Manual.

SAFETY PRECAUTIONS

When using electrical appliances, basic safety precautions should be followed, including the following:

How to Maintain Your Unit

to Receive the Most Efficient and

Successful Operation

You have selected one of the finest commercial refrigeration units made. It is manufactured under

strict quality controls with only the best quality materials available. Your TRUE cooler, when

properly maintained, will give you many years of trouble-free service.

SAFETY INFORMATION

............ www.truemfg.com ............

True Food Service Equipment, Inc.

2 2

SAFETY INFORMATION

HOW TO SAFELY DISPOSE OF USED

REFRIGERATION EQUIPMENT

DANGER!

RISK OF CHILD ENTRAPMENT

Child entrapment and suffocation are not problems

of the past. Junked or abandoned display cases are

still dangerous… even if they will sit for “just a few

days.”

It is much safer if doors and lids are removed so

children cannot get trapped inside, leaving the

shelves in place will also deter children from trying to

climb inside.

If you are getting rid of your old display case, please

follow the instructions below to help prevent

accidents. Depending on the country where the

unit is located there will be officially approved ways

of disposing of your used equipment.

It is important that care is taken in disposing of used

refrigerators or freezers. Before You Throw Away Your

Old Refrigerator or Freezer:

• Take off the doors.

• Leave the shelves in place so that children may

not easily climb inside.

Refrigerant Disposal

Depending on the country where the unit is located

there will be Officially approved way of disposing

of your used equipment. Your old refrigerator may

have a cooling system that uses “Ozone Depleting

” chemicals. If you are throwing away your old

refrigerator, make sure the refrigerant is removed for

proper disposal by a qualified service technician. If

you intentionally release any refrigerants you can be

subject to fines and imprisonment under provisions

of the environmental regulations.

............ www.truemfg.com ............

True Food Service Equipment, Inc.

SAFETY INFORMATION

Your TRUE unit will come fitted with the correct

plug for your Country (if not contact your

supplying dealer). This plug has a ground or earth

prong or pin, it must be connected to a electrical

supply outlet that is also grounding or earthed.

This minimizes the possibility of electric shock

hazard. Do not connect to any power supply if you

have any doubts. Make sure a qualified electrician

confirms that the supply is grounded or earthed.

Ensure that the supply is correct and matches that

on the unit information plate. Do not use adapter

plugs or extension leads as these can cause safety

issues and early failure of electrical components.

The use of adapters and extension cords will

invalidate your warranty. Always disconnect the

unit by pulling on the plug and not on the power

lead. Do not use the unit if the power lead has

been damaged.

IMPORTANT ELECTRICAL SAFETY INFORMATION

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.

For personal safety, this appliance must be properly grounded.

WARNING!

USE OF EXTENSION CORDS / ADAPTER PLUGS

Do not use adapter plugs or extension leads as these can cause safety issues and early failure of electrical components.

The use of adapters and extension cords will invalidate your warranty. NEVER USE AN EXTENSION CORD! NEVER USE AN

ADAPTER PLUG!

WARNING

Compressor warranties are void if compressor burns out due to low voltage.

WARNING

Power supply cord ground should not be removed!

NOTE

To reference wiring diagram - Remove lower rear grill. Wiring diagram is positioned on the inside cabinet wall.

............ www.truemfg.com ............

True Food Service Equipment, Inc.

4 4

INSTALLATION / OPERATION INSTRUCTIONS

To insure that your unit works properly from the

first day, it must be installed properly. We highly

recommend that your True unit is installed by your

supplying dealer or service company. The cost of a

professional installation is money well spent. Issues

caused by incorrect installation may invalidate your

warranty

Before you start to install your True unit, carefully

inspect it for freight damage. If damage is

discovered, immediately file a claim with the

delivery freight carrier or supplying dealer.

True is not responsible for damage incurred during

shipment.

OWNERSHIP

• Adjustable Spanner or Mole Grips

• Phillips Head Screwdriver

• Spirit Level

REQUIRED TOOLS

Step 1

The following procedure is recommended for

uncrating the unit:

A. Remove the outer packaging by pulling tri-wall

nails from skid. Remove (4) cardboard corner

pads and dust cover.

B. Inspect for concealed damage. Again,

immediately file a claim with the freight carrier

if there is damage.

C. Move your unit as close to the final location as

possible before removing the wooden skid.

Note: Keys for coolers with door locks are located in

warranty packets.

UNCRATING

INSTALLATION / OPERATION INSTRUCTIONS

Step 2

A. Remove packing material behind cabinet as a

cushion. Carefully lay the unit on its back to

remove skid.

When lifting unit remember to leave the

cabinet upright for 24 hours before

plugging into power source.

B. Remove skid by unscrewing all base rail anchor

brackets. Place skid to the side.

C. Carefully lift cabinet upright.

LOCATING

Removing skid

from bottom of

cabinet.

............ www.truemfg.com ............

True Food Service Equipment, Inc.

INSTALLATION / OPERATION INSTRUCTIONS

INSTALLATION OF LEGS AND CASTORS

Step 3

Securing Castors:

To obtain maximum strength and stability of the

unit, it is important that you make sure each castor

is secure. The bearing race on the castor of the top

edge of the leg must make firm contact with the

rail.

Unit Leveling:

Four leveling shims have been provided for leveling

castored units positioned on uneven floors. Shims

must be positioned between rail end and bearing race.

True recommends a four shim limit to any single castor.

A. Turn the bearing race counter-clockwise until

the cabinet is level. Level front to back and side to

side. (diagonally)

B. Install the desired number of shims, making sure

the slot of the shim is in contact with the threaded

stem of the castor.

C. If more than one shim is used, turn the slot at a

90° angle so they are not in line.

D. Turn the bearing race clockwise to tighten and

secure the castor by tightening the anchoring bolt

with a 3/4 inch open-end wrench, socket, or the

tool provided.

CAUTION

To avoid damage to lower rail assembly, slowly raise

unit to upright position after installing castors.

Thread four screws into castor in

the underside of cabinet frame

rail.

Anchor the four screws ﬁrmly to

the base of the unit.

1 2

............ www.truemfg.com ............

True Food Service Equipment, Inc.

6 6

INSTALLATION / OPERATION INSTRUCTIONS

Step 5

A. Before your new unit is connected to a power

supply, check the incoming voltage with a

voltmeter. If anything less than 100% of the

rated voltage for operation is noted, correct

immediately.

B. All units are equipped with a 7 ft. (2.1m) service

cord, and must be powered at proper operating

voltage at all times. Refer to cabinet data plate

for this voltage.

True requires that a sole circuit be dedicated for the

unit. Failure to do so voids warranty.

WARNING

Compressor warranties are void if compressor burns out due to

low voltage.

WARNING

Power supply cord ground should not be removed!

NOTE

To reference wiring diagram - Remove lower rear grill. Wiring

diagram is positioned on the inside cabinet wall.

ELECTRICAL INSTRUCTIONS

LEVELING

Step 4

A. Set unit in its final location. Be sure there is

adequate ventilation in your room. Under extreme

heat conditions, (100°F+, 38°C+), you may want to

install an exhaust fan.

Warning

Warranty is void if ventilation is insufficient.

B. Proper leveling of your True cooler is critical to

operating success (for non-mobile models). Effective

condensate removal and door operation will be

effected by leveling.

C. The cooler should be leveled inside the cabinet

front to back and side to side with a level.

D. Ensure that the drain hose or hoses are

positioned in the pan.

E. Free plug and cord from inside the lower rear of

the cooler (do not plug in).

F. The unit should be placed close enough to the

electrical supply so that extension cords are never

used.

Warning

Compressor warranties are void if the unit is more than 7ft.

(2.1m) from plug-in connection. TRUE will not warranty any

units that are connected to an extension cord.

............ www.truemfg.com ............

True Food Service Equipment, Inc.

INSTALLATION / OPERATION INSTRUCTIONS

Step 6

A. The compressor is ready to operate. Plug in the

unit.

B. Temperature control set at No. 4 position gives

refrigerators an approximate temperature of

35°F (1.6˚C) and freezers an approximate

temperature of -10°F (-23.3˚C). Allow unit

to function several hours, completely cooling

cabinet before changing the control setting.

C. Excessive tampering with the control could lead

to service difficulties. Should it ever become

necessary to replace temperature control, be

sure it is ordered from your True dealer or

recommended service agent.

D. Good air flow in your True unit is critical. Be

careful to load product so that it neither presses

against the back wall, nor comes within four

inches of the evaporator housing. Refrigerated

air off the coil must circulate down the back

wall.

NOTE

If the unit is disconnected or shut off, wait five minutes before

starting again.

RECOMMENDATION

Before loading product we recommend you run your True

unit empty for two to three days. This allows you to be sure

electrical wiring and installation are correct and no shipping

damage has occurred. Remember, our factory warranty does not

cover product loss!

REPLACEMENT PARTS

TRUE maintains a record of the cabinet serial number for your

unit. If at any time during the life of your display case, a part

is needed, you may obtain this part by furnishing the model

number and serial number to the company from whom you

purchased the cabinet. Call Toll-Free: (800)-424-TRUE (Direct

to Parts Department). (800)-325-6152 (U.S.A. & Canada only)

or call: (636)-240-2400.

STARTUP

Serial Number

REMOTE UNITS (This section applies to remotes only!)

• Remote cabinets must be ordered as remote.

We do not recommend converting from a

standard self contained to remote system.

• All remote cabinets must be hard wired.

• No castors available.

• All remote cabinets come standard using 404A

refrigerant.

• All remote units come standard with expansion

valve, liquid line solenoid, heated condensate

pan, and defrost timer when applicable.

• Contact True Technical Service for BTU

requirements.

• No wiring necessary between cabinet and

condensing unit.

• All remote condensing units purchased from

True are 208/230 volts single phase.

If you have any questions regarding this section,

please call True at 1-(800)-325-6152.

............ www.truemfg.com ............

True Food Service Equipment, Inc.

8 8

SHELVING INSTALLATION / OPERATION

INSTALLATION / OPERATION INSTRUCTIONS

REQUIRED TOOLS:

• Tray Slide

Step 1

Position tray slide to align front to back (level)

with rectangular hole of the standard posts.

Make sure tabs on the back-side of the tray slide

are facing down. Push in and slide down on

both ends so tabs are in the locked position.

(See figure 1).

Note

Make sure that pan slide is level front to back

within the refrigerator or freezer.

Step 2

Repeat procedure with remaining tray slides.

Note

Figure 2 illustrates correct installation of tray slide.

Figure 1

Figure 2

Tray Slide

Tray

Slide

Andere Handbücher für TGU-2

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere True Kühlschrank Handbücher

True

True TS-53-PT Bedienungsanleitung

True

True TAC-48GS Bedienungsanleitung

True

True TG1RRI-1S Bedienungsanleitung

True

True TDB-24-48-1-G-1 Bedienungsanleitung

True

True T-50-GC-S Bedienungsanleitung

True

True T-19G Bedienungsanleitung

True

True GDM-19 Bedienungsanleitung

True

True TS-23 Bedienungsanleitung

True

True TA2RRI-2G Bedienungsanleitung

True

True TWT-60D-2 Bedienungsanleitung

True

True TUC-60-32D-2 Bedienungsanleitung

True

True TR2R-2HG-2HS Bedienungsanleitung

True

True GEM-69 Bedienungsanleitung

True

True TSD-47 Bedienungsanleitung

True

True TPP-67 Bedienungsanleitung

True

True TAC-30 Bedienungsanleitung

True

True TAC-30 Bedienungsanleitung

True

True TG2RPT-2S-2S Bedienungsanleitung

True

True TWT-93 Bedienungsanleitung

True

True TUC-93 Bedienungsanleitung

True

True TA2R-2S Bedienungsanleitung

True

True TA1R-1S Bedienungsanleitung

True

True TUR-24-R/L-SS-B Bedienungsanleitung

True

True T-49-4 Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung

Teledyne

Teledyne 6712FR and Betriebsanleitung