Trust ASUN-650 Bedienungsanleitung
www.trust.com
Item 71017-02 Version 1.0
Always read the instructions
before using this product
SUN BLINDS SWITCH
USER MANUAL
MULTI LANGUAGE
START-LINE
RECEIVER ASUN-650 SWITCH-IN
ASUN-650 SUN BLINDS SWITCH
2
5
1
3-4
L L COM
N
n
e
u
t
r
a
l
w
i
r
e
l
i
v
e
w
i
r
e
L L COM
N
230V
Motor
Wire 1
(brown)
Neutral wire
(blue)
Ground (yellow/green)
230V Neutral
(Blue)
230V Live
(brown)
Wire 2
(black)
ASUN-650 SUN BLINDS SWITCH
7
9
6
8
12-24V
Motor
Switch wire A
Switch wire B
230V Neutral
(blue)
230V Live
(brown)
0 V
12-24V DC
Adapter
L L CO M
N
L L COM
N
230VAC
power supply
1
2
n
u
l
d
r
a
a
d
L LN COM
1 SEC
Set
Learn
Learn Set
ASUN-650 SUN BLINDS SWITCH
10
12
11
ON
L LN COM
13
Learn Set
ON
OFF
LED will blink fast
ASUN-650 SUN BLINDS SWITCH
14
L LN
COM
OFF
n
u
l
d
r
a
a
d
L LN COM
1 SEC
L LN COM
LED will blink fast
ASUN-650 SUN BLINDS SWITCH
n
u
l
d
r
a
a
d
L LN COM
n
u
l
d
r
a
a
d
L LN COM
L LN COM
6 SEC 1 SEC LED will blink fast
ASUN-650 SUN BLINDS SWITCH
1
1. Switch o the mains power (electric meter box)
before installing this product
2. Remove the existing switch
Detach the existing switch and disconnect the wires.
The existing wall switch is replaced by this product and can
no longer be used. Consult the supplier of your sun blind
system when in doubt about motor type and wire colors.
3. Connect 230V power supply
Connect the (brown) live wire to the [L] contact.
Connect the (blue) neutral wire to the [N] contact.
Contact an electrician when in doubt about wire colors.
Tighten the clamping screws.
4. Connect motor wiring
How to connect the motor wiring depends on
the type of motor:
• Read step 5 for a 230V motor.
• Read step 6 for a 12-24V motor.
• Read step 7 for a motor with a momentary switch.
5. Connect 230V motor
1. Connect the (blue) neutral wire from the motor to
the [N] contact.
2. Use a seperate piece of wire to connect [L] with [COM].
3. Connect the live wires from the motor (brown and black)
to the [ ] and [ ] contact. These positions can
be interchanged to reverse the up and down motion of
the motor.
6. Connect 12-24V motor
1. Connect the 24V+ wire to [COM].
2. Connect switch wires A and B to the [ ] and [ ]
contact. These positions can be interchanged
to reverse the up and down motion of the motor.
Never connect 230VAC wires to low-voltage wires.
7. Motor with momentary switch
The motor only has 2 wires.
1. Connect one wire to [ ] and the other wire to [COM].
These positions can be interchanged to reverse the up
and down motion of the motor.
2. Use a seperate piece of wire to connect both
[ ] and [ ] contacts. Never connect 230VAC wires to
low-voltage wires.
8. Switch on the mains power (electric meter box)
to continue the installation
Shock hazard! Do not contact any exposed wiring.
Only touch the plastic housing of this product.
9. Activate learn-mode
Press the learn-button on the receiver for 1 second.
The learn-mode will be active for 12 seconds and the
LED-indicator will blink slowly.
10. Assign Trust Smart Home transmitter code
While the learn-mode is active, send an ON-signal with any
Trust Smart Home transmitter to assign the code to the
receiver’s memory.
EN
ASUN-650 SUN BLINDS SWITCH
2
EN
11. Code confirmation
The LED indicator of the receiver will blink fast to confirm
the code has been received. The receiver can store up to
32 dierent transmission codes in its memory. The memory
will be preserved when the receiver is moved to another
location or in case of power failure.
12. Install the receiver
Install the receiver in a standard junction box or other type
of housing (break o the mounting tabs if necessary).
Close the housing with a blind cover.
13. Manual operation with a Trust Smart Home
transmitter
1. Send an ON-signal to raise the screen.
2. Send an ON-signal again to stop.
3. Send an OFF-signal to lower the screen.
4. Send an OFF-signal again to stop.
Momentary switch only: every command (up/down/stop)
needs to be given twice.
14. Explanation COM-contact
The module contains 2 voltage-free contacts: [ ] and [ ].
In the neutral position, the contact [COM] is not switched.
After an on/o signal from a Trust Smart Home transmitter,
[COM] switches either to the [ ] or [ ] contact. After
2 minutes, the COM contact switches back to its neutral
position.
Single code delete
1. Press the learn-button for 1 second. The learn-mode
will be active for 12 seconds and the LED-indicator will
blink slowly.
2. While the learn-mode is active, send an OFF-signal to
delete the code of a specific Trust Smart Home transmitter.
3. The LED indicator will blink fast shortly to confirm
transmitter code deletion.
Full memory delete
1. Press and hold the learn-button on the receiver
(aprox. 6 sec.) untill the LED-indicator starts blinking fast.
The delete mode will be active for 12 seconds.
2. While the delete mode is active, press the learn button
on the receiver again for 1 second.
3. The LED indicator will blink fast shortly to confirm
memory deletion.
For information about the SET button please go to
www.trust.com/71017
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Sprachen:
Andere Trust Schalten Handbücher
Trust
Trust 411F Bedienungsanleitung
Trust
Trust SECURITY PLUS-LINE AGST-8800 Bedienungsanleitung
Trust
Trust START-LINE AWST-9000Z Bedienungsanleitung
Trust
Trust SMART Home START-LINE RECEIVER ACM-1000 Betriebsanleitung
Trust
Trust SMART Home AWMR-230 Bedienungsanleitung
Trust
Trust SMART Home START-LINE RECEIVER AWS-3500 Betriebsanleitung
Trust
Trust START-LINE ACM-2300-HC Bedienungsanleitung
Trust
Trust HU-4140P Bedienungsanleitung
Trust
Trust START-LINE AMU-500 Bedienungsanleitung
Trust
Trust PREMIUM ZCM-1800 Bedienungsanleitung
Trust
Trust START-LINE ACM-2000 Bedienungsanleitung
Trust
Trust START-LINE AGST-8800 Bedienungsanleitung
Trust
Trust START-LINE APA3-1500R Bedienungsanleitung
Trust
Trust 12914 Bedienungsanleitung
Trust
Trust SECURITY PLUS-LINE AGST-8800 Bedienungsanleitung
Trust
Trust 71075 Bedienungsanleitung
Trust
Trust 300SB Bedienungsanleitung
Trust
Trust HU-4445p Bedienungsanleitung
Trust
Trust SMART Home Security Plus-Line AGST-8802 Bedienungsanleitung
Trust
Trust APC Starter Set Wireless Switching Bedienungsanleitung
