Tsubaki FLATVEYOR ZP Bedienungsanleitung

Tsubaki

FLATVEYOR ZP Type

Construction・Part name

Precautions

Since welded ends tend to peel off in the tearing direction,

do not allow forces in the tearing direction to work on the

weldedends.

Please handle cables and tubes with care when wiring or

installing them inequipment.

ｓあきｓ

Be sure to fix the device in a bent position with the locking

part facing theoutside.

Fixing one end (fixed ormoving end) to the device while

the Flatveyorisstraightenedmay causethesupport

membertobe fixedinthe notbendingdirection.

Bendinginthiscondition coulddamagethe support

member.

※Actualsupportmembertubeisblackorwhite

Instruction Manual

Caution: Alwaysweartheappropriateprotectivegear(safetyglasses,gloves,safetyshoes,etc.) whenworking.

Cap

（Blackonly）

Support member

Becarefulnot toallow

forces in tearing

direction.

Donotfix one

endof the

Flatveyorwhileit

is straightened.

When the supportmember is

fixed inadirection thatis not

thebendingdirection,it will

breakifbentinthatcondition.

Openabletube

(Two lineupsofBlackand White)

Outside

Lockingpart

Support membertube

(Two lineupsof Black and White)

When fixing thecable/tube,make sure to provide a

suitable amount of play.

Otherwise, the openable tube could tear, or the locking

part may open.

Do not fix the cable/tube inside the openable tube with a

cabletie.

Itcouldtear theopenabletube.

Refer to the table on the right for the cable/tube to be

installedintheopenable tube.

When multiple cables/tubes are to be installed, the

differenceinouter diametershouldbe 5mmorless.

Numberofcables/tubesstored

1pc

2 pcs

3pcs

φ11orless

side-by-side

13mmor less

φ4 or less and

3 pcs orless

The Flatveyormaytilt duetothe carling ofthecable/tube.

Cable/tube should be routed without twisting. Do not pull

the cable/tube out from the drum orcoil in a spiral pattern

because this will cause the cable/tube to be routed with a

twist.

■Use cables/tubes that areflexible, repeatedlybendable, durable, and slippery.

■For installationofcables/tubes, ensure that thecableweight is symmetrically distributedacross thewidthoftheFlatveyor.

■Please removeany inclusions on thefloororoperating areawherethe Flatveyorisinstalled, as theymay causedamage.

■Do not install any object on the inner side of the Flatveyor that may contact it.

■Periodically check that the locking part of the openable tube is not open, that there are no inclusions that could damage on

the floor or operating area where the Flatveyor is installed, and that the cable/tube is notpulled into the openable tube.

Ifany abnormality is foundduring the inspection,maintenanceshould beperformed.

Suitableplay

TooTight

Too loose

Cable/tube installation

①Open the locking part from the end of the openable

tube.

②Installthe cable/tube inside the openable tube.

When installing multiple cables/tubes in one openable

tube, keep thecables/tubesaligned.

Storing with twist may cause premature wire breakage

duetoentanglementofcablesin the openabletube.

③To close the openable tube properly, make sure that

section A in the right figure of the locking part is

correctly overlapped and does not come outside of the

openable tube.

It is important that the section A is properly overlapped

around the cable/tube over the entire length of the

Flatveyor. If not properly overlapped, the locking part

couldopen.

④Tightenthe openable tube temporarily by hand and

close the locking part with closing toolfrom the end.

(Also closable by hand.)

Afterclosingthe lockingpart, ensurethat the

cable/tubedoesnotexertanyoutward force on the

endof lockingpart.Otherwise,thelocking partcould

open.

※Closingtoolisnotincluded.Please orderseparately.

⑤Make sure that the locking part is closed properly. If the

gap between the locking part is not uniform or if a

locking part opens, section A may not be overlapped

correctly.

Correctly overlap section A and close the locking part

again.

Section Ais

bent.

Routedwith twist

Closingtool

Open

Gapis not

uniform

Uniformgap

Section Aiscorrectly

overlapped.

Section Aiscaught on

thearrowhead side.

Installation procedure

Wheninstalling,mounttheclampinthepositionindicated inourdrawingor catalogs

①After inserting cable/tube and before fixing it to the

equipment, make sure that the locking part of the

openable tube is facing the outside and Flatveyor should

bebentas shownonthe right beforefixing

②Fix the fixed end and moving end in bent position to the

equipmentwithclamp.

③Make sure that the locking part of openable tube is

properly closed.

Close properlyifitis open.

④Fix each cable/tube near the exit of the openable tube

with a cable tie, etc. at both fixed end side and moving

end side, so that unnecessary tension is not applied on

it.

Fixing them under tension and operating could cause

the openable tube to tear.

⑤After fixing the fixed and moving ends, check that there

is no tilt in the bending section of the Flatveyor and that

the unsupportedlength is nottwisted.

Then, move the Flatveyor slowly and check that each

cable/tube is notpulled into the openable tube.

Also, check that there are no other abnormalities in

operation.

Issued October 1, 2022 🄫Tsubakimoto Chain Co.

Fixwith cable tie

Inclination ofbending section

Twistingof

unsupported length

Lockingpartis

open.

Lockingparttoface

outside

Clamp

Fixtotheequipmentwithclamp.

（Fixedend,Movingend）

Andere Tsubaki Industrieanlagen Handbücher

Tsubaki

Tsubaki TKRB14H10 Bedienungsanleitung

Tsubaki

Tsubaki L Series Bedienungsanleitung

Tsubaki

Tsubaki Power-Lock AS Series Bedienungsanleitung

Tsubaki

Tsubaki MZEU Series Technische Daten

Tsubaki

Tsubaki 200 Series Technische Daten

Tsubaki

Tsubaki TKP25H15 Bedienungsanleitung

Tsubaki

Tsubaki CR3812 Bedienungsanleitung

Tsubaki

Tsubaki TKR15H22 Bedienungsanleitung

Tsubaki

Tsubaki ECHT-FLEX NEF130W Bedienungsanleitung

Tsubaki

Tsubaki BB Series Bedienungsanleitung

Tsubaki

Tsubaki OLDHAM COUPLING Bedienungsanleitung

Tsubaki

Tsubaki TKA30H20 Bedienungsanleitung

Tsubaki

Tsubaki TGM Series Bedienungsanleitung

Tsubaki

Tsubaki TL200 Bedienungsanleitung

Tsubaki

Tsubaki PB Series Bedienungsanleitung

Tsubaki

Tsubaki Cableveyor TKP35H22 Bedienungsanleitung

Tsubaki

Tsubaki BSEU Series Technische Daten

Tsubaki

Tsubaki Cableveyor TKP68H46 Bedienungsanleitung

Tsubaki

Tsubaki TGB Series Bedienungsanleitung

Tsubaki

Tsubaki MGUS Series Technische Daten

Tsubaki

Tsubaki Backstop BS-F Series Bedienungsanleitung

Tsubaki

Tsubaki ECHT-FLEX COUPLING NES Series Bedienungsanleitung

Tsubaki

Tsubaki TGB Series Bedienungsanleitung

Tsubaki

Tsubaki EW Series Bedienungsanleitung

Beliebte Industrieanlagen Handbücher anderer Marken

ABB

ABB Unifix AD Handbuch

Mark 7

Mark 7 Evolution Bedienungsanleitung

Husky

Husky HyPET Bedienungsanleitung

bora

bora PM-1800 Bedienungsanleitung

Grizzly

Grizzly T32428 Bedienungsanleitung

Siemens

Siemens 8MF1 Series Bedienungsanleitung

ABB

ABB HT610965 Bedienungsanleitung

ABB

ABB SafeLink Bedienungsanleitung

Phoenix

Phoenix PHX-150 Bedienungsanleitung

ABB

ABB A165-L32 Bedienungsanleitung

ABB

ABB HT842936 Bedienungsanleitung

Hermetica

Hermetica 10 Series Bedienungsanleitung

HORNER

HORNER OEE Solution Bedienungsanleitung

Hammerhead

Hammerhead HG375 Bedienungsanleitung

SCHUNK

SCHUNK VERO-S NSE-A3 138 Gebrauchsanweisung

ABB

ABB HT566657 Bedienungsanleitung

Webasto

Webasto GSE CAN Bedienungsanleitung

ABB

ABB HT614003 Bedienungsanleitung