Tucker Barbecues Horizon Montageanleitung
V10.08.2021
IMPORTANT – PLEASE READ ALL INSTRUCTIONS
BEFORE YOU ASSEMBLE, INSTALL OR
OPERATE THIS APPLIANCE.
ASSEMBLY, INSTALLATION AND
OPERATING INSTRUCTIONS FOR
HORIZON BARBECUE
1
IMPORTANT SAFETY INSTRUCTIONS
BARBECUE ASSEMBLY INSTRUCTIONS
INSTALLATION INSTRUCTIONS & WARNINGS
SPECIFICATIONS
DIMENSIONS
GAS INSTALLATION AND
LEAK TEST PROCEDURE
OPERATING INSTRUCTIONS
COOKING HINTS
TROUBLESHOOTING
SERVICE & MAINTENANCE
WARRANTY
2
3
6
8
9
11
14
15
16
18
19
CONTENTS
V10.08.2021
2
IMPORTANT SAFETY
INSTRUCTIONS
• Tucker Horizon Barbecues are approved for
outdoor use only.
• Remove all plastic protection lm from stainless
steel components before assembly.
• Clean your barbecue regularly; check the
grease tray for excess grease build up, as
damage by grease or fat re is not covered by
warranty.
• Always turn off gas supply when you nish
barbecuing.
• A canvas cover for this barbecue will extend its
life and ensure trouble free operation.
• For installation of this barbecue onto a cabinet
trolley refer to relevant instructions.
• Attend an operating barbecue at all times.
• Do not use indoors or in any enclosed area.
• Do not spray aerosols in the vicinity of this
appliance while it is in operation.
• Do not place articles on or against this
appliance.
WARNING FOR
YOUR SAFETY
If you smell gas:
1. Shut off gas supply to appliance.
2. Extinguish any open ame.
3. Open lid or hood.
4. If odor continues, immediately call your gas
supplier or your Fire Department.
• Failure to follow these instructions may cause
serious bodily injury or damage to property.
• Read all instructions carefully before assembly
and usage of barbecue.
• This barbecue must not be used indoors.
• Keep this manual for future reference.
• Do not store spare gas bottles, petrol, ammable
vapours or liquids in the vicinity of this barbecue.
• Do not use or store ammable liquids in or near
this appliance.
• Always leak test /check hose connections after
lling cylinders.
• Check cylinder condition for rust and that the date
stamp is current as every gas cylinder in Australia
must be pressure tested every ten years.
• Never disconnect the barbecue whilst it is running.
• Do not modify this appliance.
• Do not allow children to operate the barbecue.
• If a grease/fat re should arise, turn off the gas
supply immediately until extinguished.
• Always open the lid or hood before lighting.
HAZARDOUS FIRE OR EXPLOSION MAY RESULT
IF INSTRUCTIONS ARE IGNORED.
It is the consumer’s responsibility to see that the
barbecue is properly assembled, installed and taken
care of. Failure to follow instructions in this manual
could result in injury and /or property damage.
3
BARBECUE ASSEMBLY
INSTRUCTIONS
10mm spanner
TOOLS REQUIRED FOR ASSEMBLY
BARBECUE PARTS
• Remove the pallet and any plastic lm protecting
or covering any parts of the Barbecue and
Cabinet Trolley before assembly.
• Cut away any packaging or cable ties that may
be holding components in place.
• Check you have all the correct components as
listed below.
1x Horizon Barbecue Body
1x Grill 1x Plate
1x Heat Diffuser
1x Hose & Regulator
1x Grease Storage Tray
4
2. Place the stainless steel cooking grill above the
diffuser at the back of the BBQ and place the
cooking plate at the front of the BBQ.
1. Place the heat diffuser above the rear burner, it
locates into the slots provided in the BBQ body.
BARBECUE ASSEMBLY
Check that you have the correct gas type
Barbecue i.e. L.P.GAS (red sticker) NAT GAS
(black sticker). The label is located on the right
hand side of the Barbecue body next to the gas
inlet.
A mobile trolley is optional. If you have one,
read the assembly instructions and t the
barbecue onto the trolley before nal barbecue
assembly.
Roasting hoods are also optional, if so t roasting
hood last, reading separate hood instructions on
assembly and installation.
5
3. Open the ap on the left hand side of the BBQ
and slide the grease tray into place under the
lip of the cooking plate as shown in the photo
below then close the ap.
Once you have assembled the barbecue
wipe it over to remove greasy ngerprints
with stainless steel polish or a little baby oil on
a soft cloth, works well and also protects the
barbecue from corrosion i.e. tea staining.
6
INSTALLATION INSTRUCTIONS
& WARNINGS
• An enclosure with walls on all sided, but at least
one permanent opening at ground level and no
overhead cover. (gure 1)
• Within a partial enclosure that includes an
overhead enclosure and no more than two walls.
(gure 2)
• Within a partial enclosure that includes an
overhead cover and more than two walls, the
following shall apply. (gure 3,4 ,5)
• At least 25% of the total wall area is completely
open.
• At least 30% of the remaining wall area is open
and unrestricted.
• In the case of balconies, at least 20% of the total
of the side, back and front wall areas shall be
and remain open and unrestricted.
For alternative types of installations, contact your
nearest dealer.
BARBECUE INSTALLATION INSTRUCTIONS
READ THE IMPORTANT INFORMATION
ON THE FRONT OF THE BARBECUE
This barbecue is designed and approved for outdoor
use only.
Be mindful of the location of installation of the
barbecue.
When deciding on a location to install your
BBQ, we recommend that you install it with the
prevailing wind blowing into the front of the BBQ.
Do not use this appliance indoors or on marine craft.
This appliance shall only be used in an above
ground, open-air situation with natural ventilation,
without stagnant areas where gas leakage and
products of combustion are rapidly dispersed by
wind and natural convection.
Any enclosure in which the appliance is used shall
comply with one of the following:
The intended use of this barbecue is to be installed
into cabinetry or brickwork. It may be placed onto a
bench or cut into an opening in a bench.
Be sensible about the location of your barbecue.
The barbecue must be located on a solid and level
surface that can safely support the BBQ.
Do not locate the barbecue near combustible
materials or surfaces, either above or around the
barbecue such as over hanging trees, bushes or
ammable liquids and the like.
Do not obstruct any of the air ventilation openings on
the front of the barbecue.
Strong winds blowing into the back or across
the back of the Roasting Hood can cause
overheating of the BBQ.
The Roasting Hood is designed so that Hot air
is released through a vent in the back of the
Hood. When the Roasting Hood is shut strong
winds can prevent the hot air escaping out of
this vent and may even in some cases push
the hot air down and out the front of the BBQ
which can cause damage to the ignition
system and control valves.
INSTALLATION WARNINGS
7
DIAGRAMMATICAL REPRESENTATIONS OF
OUTDOOR AREAS
FIGURE F1 – OUTDOOR AREA – EXAMPLE 1
FIGURE 4 OUTDOOR AREA –EXAMPLE 4
FIGURE F2 – OUTDOOR AREA – EXAMPLE 2
FIGURE F5 – OUTDOOR AREA – EXAMPLE 5
FIGURE F3 – OUTDOOR AREA – EXAMPLE 3
The following gures are diagrammatical
representations of outdoor areas. The areas used in
the gures below are examples – the same principles
apply to any other shaped area.
Both ends open
Open side at least 25%
of total wall area
30% or more in total
of the remaining wall
area is open and
unrestricted.
OPEN AT SIDE AT LEAST 25% OF TOTAL WALL AREA. 30% OR
MORE IN TOTAL OF THE REMAINING WALL AREA IS OPEN
AND UNRESTRICTED.
OPEN SIDE AT LEAST 25% OF TOTAL WALL AREA. 30% OR
MORE IN TOTAL OF THE REMAINING WALL AREA IS OPEN
AND UNRESTRICTED.
Open side at least 25%
of total wall area
30% or more in total
of the remaining wall
area is open and
unrestricted.
8
BARBECUE GAS CONSUMPTION
TUCKER HORIZON BARBECUES ARE MADE
AND APPROVED TO AUSTRALIAN STANDARDS
A.G.A. Certicate Number 7932
SPECIFICATIONS
(In Mega Joules Per Hour)
Natural Gas LPG:
Consumption 48mj/h 52mj/h
Natural Gas injector size 2.4mm Pressure 1KPA
Propane Gas injector size 1.5mm Pressure 2.75 KPA
For LP Gas connections, an approved 2.75 KPA
regulator and hose assembly connection to the
appliance is tted by the manufacturer.
The appliance inlet is 3/8 S.A.E. male and is located
under the right hand side rear of the barbecue.
The minimum capacity propane cylinder for this
barbecue is 4 KG.
The intended use of this barbecue is to be installed
onto a Tucker cabinet stand.
Alternatively it may be set into brickwork or similar
non combustible surface.
Be sensible about the location of your barbecue.
The barbecue must be located on rm and level
ground.
Do not locate the barbecue near combustible
materials or surfaces, either above or around the
barbecue.
Do not obstruct any of the air ventilation openings
on the sides of the barbecue when installing
into brickwork, make sure to leave 200 square
centimeters minimum air ventilation underneath.
Warning in freezing conditions the pressure of
Propane gas can be reduced in the Cylinder
Tank causing a lack of gas pressure, this may
affect the way the barbecue operates.
9
HORIZON BBQ DIMENSIONS
DIMENSIONS
477.6mm
Gas Manifold
518mm
768mm
924mm
796.5mm
822.5mm
468mm
213mm
69mm
924mm
776mm
35mm
822.5mm
761.8mm
477.6mm
518mm
26.2mm
69mm
251.8mm 238.8mm
26.2mm
48.5mm
67.8mm
Gas Manifold
The manifold is factory tted at the back on the right-hand side. Manifold diameter is 20mm square tube.
The roasting hood is ush with the back of the BBQ when open. The at lid is 35mm high when shut and
510mm high when open.
Inhaltsverzeichnis
Andere Tucker Barbecues Grill Handbücher
Tucker Barbecues
Tucker Barbecues GTR Series Gebrauchsanweisung
Tucker Barbecues
Tucker Barbecues S Wok Montageanleitung
Tucker Barbecues
Tucker Barbecues GT Series Montageanleitung
Tucker Barbecues
Tucker Barbecues CHARCOAL DELUXE Montageanleitung
Tucker Barbecues
Tucker Barbecues GTRL1 Bedienungsanleitung
Tucker Barbecues
Tucker Barbecues GTR Series Montageanleitung
Tucker Barbecues
Tucker Barbecues GTR Series Montageanleitung
