TURNTIDE VES-Artex 55" ECV Storm Installationsanleitung

55” ECV

Storm

Assembly Instruction Manual

ves-artex.com | 1.888.622.2999

SAVE THIS MANUAL FOR FUTURE REFERENCE

WI-G-018-55_ECV_STORM-01

55” ECV STORM | Assembly Instruction Manual

STEP

DESCRIPTION

2.1

Tools that you will need for the assembly are:

- 4mm key

- 5mm key

- 5mm socket

- 10mm socket

- 10mm wrench

- 13mm wrench

- 17mm socket wrench

- 22mm socket wrench

- Metric tape measure

Assemble the impeller

Check the parts with stickers shown below –Check blades, hub and pulley, they should all have A, B, C, D, E, and F

stickers on them

Install the fan blades

Place 6 fan blades A, B, C, D, E and F on the ground with the fan blade holder in the corresponding position. Pre-

assemble screws, but do not tighten them. Pick up the fan blade, place it on top of the fixture, align it and position

it. When the fan blade stops shaking, tighten the screws with a tool，The same process as blade B, C, D, E and F.

then tighten all the bolts and nuts, the socket size is 10mm, the torque is 15-18NM

55” ECV STORM | Assembly Instruction Manual

2.2

Fix the impeller to the big pulley

Reverse the impeller and put on the floor or table, attach the big pulley with black spacer to the hub, the sticker

number need to match, align the hole then attach the 6 M6x20 bolts,6 spring washers and 6 6x12 washers, tighten

all the bolts. The key size is 5mm, the torque is 15NM

55” ECV STORM | Assembly Instruction Manual

Assemble the mid-post and bracket

Put the mid-post and brackets on the floor or table, take care the folding direction of the brackets, then attach to

the mid-post with M8x60 bolts, 8x25 washers and M8 lock nuts, tighten all the bolts and nuts except bolts for the

tensioner bracket, make sure the bracket is vertical and flat to the mid-post, the socket wrench size is 17mm, the

torque is 35NM.

55” ECV STORM | Assembly Instruction Manual

Assemble the impeller to the mid-post

Attach the belt xpa 1732 to the big pulley, then attach the big pulley to the mid-post with M14x120 bolts, 2 ø40

washers and M14 lock nut, you need to use the socket with handle which total lengh not less than 120mm, the

socket wrench size is 22mm, the torque is 120NM. Put the black plug inside the hub.

55” ECV STORM | Assembly Instruction Manual

5.1

Assemble the motor with motor base and pulley

Fix the motor to the motor base

Attach the motor base to the motor with two M8 carriage bolts ,2 8x16 washers and two lock nuts on the two top

holes, for the bottom two holes, use M8x30 bolts, but need to put 2 14x40 washers for each hole between the

motor foot and the motor base, the washers 8x16 are on the motor side, washers 8x25 on the motor base side,

make sure the motor is in good position then tighten all the bolts, the wrench size is 13mm, the torque is 30NM

55” ECV STORM | Assembly Instruction Manual

5.2

Fix the pulley to the motor

Aline the pulley and the motor shaft and push the pulley inside the shaft until cannot go forward, then attach two

M8x16 setscrews to the holes of pulley and tighten, the key size is 4mm

55” ECV STORM | Assembly Instruction Manual

6.1

Assemble SMC housing

Put 4 pieces SMC housing on the floor (it is better to put on the 2mx2m table, and the height of the table is good

for your operation), attach the two pieces on the joint, make sure place 1A and 1A are touched, the two housing

have no movement. Attach the M6x25 bolts and 6x20 washers and M6 lock nuts. Tighten the bolts and nuts in

turns(please see the following last picture) , the wrench size is 10mm and the torque is 15NM. The same process as

other SMC housings.

55” ECV STORM | Assembly Instruction Manual

6.2

7.1

Attach M6x25 bolts, 6x20 washers and M6 nuts and tighten with cross screwdriver and 10mm wrench, the torque is

15NM.

Assemble the steel frame with the housing

Fix the steel frame to the housing

Reverse the housing finished in step 5-2, check the side with 6holes drilled in step5-2, the distance of

left two holes is more than the right two holes( please see the following first picture), put the steel

frame inside of the housing, the motor or tensioner bracket is put on the left side. The housing needs

to be 90mm at least away from the floor. Put 4 L brackets on four corners and attach the M6x25 bolts,

6x20 washers, spring washers and eye nuts, then tighten the eye nuts. Attach M6x25 bolts, 6x20

washers and M6 lock nuts to the L brackets, mid-post and the two middle brackets, then tighten with

10mm wrench and the torque is 15NM.

55” ECV STORM | Assembly Instruction Manual

Inhaltsverzeichnis

Andere TURNTIDE Lüfter Handbücher

TURNTIDE

TURNTIDE VES-Artex ECVD72 Bedienungsanleitung

TURNTIDE

TURNTIDE VES-Artex Storm Bedienungsanleitung

TURNTIDE

TURNTIDE VES-Artex AFRV72 Bedienungsanleitung

TURNTIDE

TURNTIDE VES-Artex PPFD72 Bedienungsanleitung

TURNTIDE

TURNTIDE VES-Artex PPF AIR PPFS55 Bedienungsanleitung

TURNTIDE

TURNTIDE VES-Artex INDC60ODP Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Hinkley

Hinkley HIGHLAND Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung