TXCOM TRACEABILITY Tinyom II Bedienungsanleitung
Ref. TinyomII_Quick guide_v03 du 08/12/15
TINYOM II
Quick Guide
Package contents
•1x Tinyom II 1D ou 1D/2D
•1x Battery pack
•1x Battery pack charging stand
•1x Electric power supply
Tinyom II Presentation
1- Scanner window
2- Trigger keypad
3- Status Leds (green, red and blue)
4- Battery pack
5- Battery lock
6- Sound output
7- Glove
1Charging the Battery pack
Connect the electric power supply to the charging stand.
Connect the electric power supply to the electric network.
Insert the battery pack in the charging stand.
- Slide the blue battery lock towards the inside of the charging stand.
- Position the battery pack onto the charger runners.
Green led: The battery pack is fully charged
Red led: The battery pack is charging
Remove the battery pack from the charging stand.
- Slide the blue battery lock towards the inside of the
charging stand.
- Lift the battery pack.
1
34
5
6
7
1
2
2Position the TINYOM II on the glove
3Insert and remove the battery pack from Tinyom II
4Position the glove on the hand
Insert the battery pack in the Tinyom II
- Slide the lock towards the keypad of the Tinyom II.
- Position the battery pack onto the Tinyom II
runners.
The Tinyom II starts automatically after battery
pack insertion.
Lift the side rubbers and slide them onto the Tinyom II « ears ».
- Position the small strap around the palm (A)
- Position the wide strap around the wrist (B)
Remove the battery pack from the Tinyom II
- Slide the lock towards the keypad of the Tinyom II
- Lift the battery pack.
Ref. TinyomII_Quick guide_v03 du 08/12/15 2
A
BA
BAB
5Beam activation
6Bluetooth connections
Scanner beam activation can be done with the keypad or accelerometer.
Keypad Accelerometer (default setting)
Information when barcode reading
Tinyom II
status
Red led
Green led
Blue
led
Buzzer
Barcode
reads and
transmitted
OFF
ON 3s
ON
1 Beep
Barcode reads and not
transmitted because no
bluetooth
connection.
ON 3s
OFF
OFF
4
Beeps
Barcode
not reads
OFF
OFF
ON / OFF
0
Beep
Press with a finger or any
part of the body.
Tilt up by +30° in a stable position, green led
+ buzzer will activate, then aim the barcode.
HID Connection
- Set the default settings (see end of doc)
- Scan the HID profile barcode.
- Scan the keyboard emulation barcode
Ref. TinyomII_Quick guide_v03 du 08/12/15 3
+30°
Ref. TinyomII_Quick guide_v03 du 08/12/15 4
7TINYOM II Power Down
8Restart the TINYOM II
SPP Slave connection
- On a PC, tablet, smartphone do a Bluetooth device research and connect the
Tinyom II. Tinyom II is named SW61B-xxxxxxxxxxx.
- When the Tinyom II is connected, the blue led is ON constantly.
- Set the default settings (see end of doc).
On a PC, tablet, smartphone do a Bluetooth device research and pair the Tinyom II.
Tinyom II is named SW61B-xxxxxxxxxxx.
- Write the pin code « 0000 ».
The connection is not complete yet. A serial connection should still be made. The
blue led will then light up.
Power down will occur automatically in the following cases:
- If Bluetooth connection is without activity during one hour (default parameter).
- If there is not Bluetooth connection during 5 minutes (default parameter).
- By reading the barcode below.
Green led Red led
> 80%
ON OFF
40% à 80%
Flashing OFF
20% à 40%
Flashing Flashing
4% à 20%
OFF Flashing
<= 4%
OFF ON
Press the sensitive sensor for 1 second. 2 beeps indicate the power up of the scanner.
During the 8 seconds startup, the Green and Red leds give the charge level of the
battery pack.
Default factory settings
Parameters and guidance of uses are details in the
User Manual. Refer it for all others information.
Inhaltsverzeichnis
Andere TXCOM TRACEABILITY Barcode-Lesegerät Handbücher
Beliebte Barcode-Lesegerät Handbücher anderer Marken
POSMicro
POSMicro Datalogic PowerScan D7100 Bedienungsanleitung
Marson
Marson MT780 Kurzanleitung zur Einrichtung
NCR
NCR RealPOS Bedienungsanleitung
Motorola
Motorola SE3300 Kurzanleitung zur Einrichtung
Element
Element P130BT Bedienungsanleitung
Motorola
Motorola Symbol LS3008 Installations- und Betriebshandbuch
