TYAN Thunder K7X Pro (S2469) Bedienungsanleitung

http://www.TYAN.com

Thunder K7X Pro ///

S2469

Revision 1.50

may be reproduced or translated without prior written consent from TYAN Computer Corp.

All registered and unregistered trademarks and company names contained in this manual are

property of their respective owners including, but not limited to the following.

TYAN, Thunder K7X Pro S2469 are trademarks of TYAN Computer Corporation.

AMD, Athlon, and combinations thereof are trademarks of AMD Corporation.

Phoenix, PhoenixBIOS are trademarks of Phoenix Software Inc.

Microsoft, Windows are trademarks of Microsoft Corporation.

IBM, PC, AT, PS/2 are trademarks of IBM Corporation.

Winbond is a trademark of Winbond Electronics Corporation.

Information contained in this document is furnished by TYAN Computer Corporation and has been

reviewed for accuracy and reliability prior to printing. TYAN assumes no liability whatsoever, and

disclaims any express or implied warranty, relating to sale and/or use of TYAN products including

liability or warranties relating to fitness for a particular purpose or merchantability. TYAN retains the

right to make changes to product descriptions and/or specifications at any time, without notice. In

no event will TYAN be held liable for any direct or indirect, incidental or consequential damage,

loss of use, loss of data or other malady resulting from errors or inaccuracies of information

contained in this document.

http://www.TYAN.com

Table of Contents

Before you begin…

Chapter 1: Introduction

1.0 Congratulations

1.1 Hardware Specifications

1.2 Software Specifications

Chapter 2: Board Installation

2.0 Board

2.1 Board Jumpers

2.2 Jumper Summary

2.3 Front Panel Connectors (J12)

2.4 Chassis Intrusion Header (J15)

2.5 CMOS Reset (J21)

2.6 10/100Mbit LAN LED (J33)

2.7 USB Header (J36)

2.8 Front Side Bus 133MHz Select

2.9 Front Side Bus 100MHz Select

2.10 Onboard SCSI (J80)

2.11 Onboard ATI Rage XL (J85)

2.12 Onboard GbE (J88) and 10/100Mbit

Ethernet (J86)

2.13 Primary PCI Speed (J92)

2.14 GbE Front Panel LED (J102)

2.15 FAN connectors

2.16 Mounting the Motherboard

2.17 Installing the Memory

2.18 Installing Processors and Heatsinks

2.19 Attaching Drive Cables

2.20 Installing Add-In Cards

2.21 Connecting External Devices

2.22 Installing the Power Supply

2.23 Finishing Up

Chapter 3: BIOS Setup

3.0 Main BIOS Setup

3.1 Advanced Setup

3.2 Chipset Configuration

3.3 Keyboard Configuration Screen

3.4 I/O Configuration

3.5 PCI Configuration

3.6 Security Setup

3.7 Power Setup

3.8 Boot Setup

3.9 Exit

Chapter 4: Diagnostics

4.0 Beep Codes

4.1 Flash Utility

Appendix: Glossary

Technical Support

.……………………………………………..Page 3

.……………………………………………..Page 4

.……………………………………………..Page 5

.……………………………………………..Page 6

.……………………………………………..Page 7

.……………………………………………..Page 8

.……………………………………………..Page 9

.……………………………………………Page 10

..…………………………………………..Page 10

..…………………………………………..Page 11

..…………………………………………..Page 12

..…………………………………………..Page 13

..…………………………………………..Page 14

..…………………………………………..Page 16

..…………………………………………..Page 18

..…………………………………………..Page 20

..…………………………………………..Page 21

..…………………………………………..Page 22

..…………………………………………..Page 23

..…………………………………………..Page 25

..…………………………………………..Page 26

..…………………………………………..Page 27

..…………………………………………..Page 28

..…………………………………………..Page 29

..…………………………………………..Page 30

..…………………………………………..Page 31

..…………………………………………..Page 36

http://www.TYAN.com

Before you begin…

Check the box contents!

The retail motherboard package should contain the following:

1x Thunder K7X Pro motherboard

1x 34-Pin floppy drive cable

1x LVD SCSI cable (if optional SCSI included)

1x Ultra-DMA-100/66 IDE cable

1x Cable set: 9-pin Serial

1x Thunder K7X Pro user’s manual

1x Thunder K7X Pro Quick Reference guide

1x TYAN driver CD

1x Adaptec SCSI driver diskette (if optional SCSI included)

1x I/O shield with 2 LAN ports

If any of these items are missing, please contact your vendor/dealer for replacement before

continuing with the installation process.

http://www.TYAN.com

Chapter 1: Introduction

1.0 –Congratulations

You are now the owner of one of the most flexible TYAN dual AMD Athlon motherboards

available. Utilizing the latest chipset technology for dual AMD multi-processing, the Thunder K7X

Pro is fully capable of handling all your heaviest software demands. If networking is what you

need, then the Thunder K7X Pro has enough bandwidth through the use of one Gigabit Ethernet

and10/100Mbit Ethernet ports.

All this is done efficiently and conveniently as the Thunder K7X Pro is ready to fit in even the

tightest spots. Thoughtfully designed, all aspects of the Thunder K7X Pro were designed from the

ground up to support even the thinnest 1U chassis.

Remember to visit TYAN’s Website at http://www.TYAN.com. There you can find information on

all of TYAN’s products with FAQs, online manuals and BIOS upgrades.

1.1 –Hardware Specifications

Processor

• Dual PGA462 ZIF sockets

• Supports up to two AMD Athlon MP

• Two onboard VRMs

• Front-Side Bus support for 200MHz and

266MHz

Chipset

• AMD 760 MPX chipset

• AMD 762 system controller (north bridge) and

AMD 768 peripheral bus controller (south

bridge)

• Winbond W83627HF Super I/O ASIC

• Winbond W83782D hardware monitoring IC

Memory

• Four 184-pin 2.5V DDR DIMM sockets

• 25-degree angled sockets enable rackmount

installation

• Supports up to 4GB of Registered

PC2100/1600 DDR memory

• Also supports ECC (72-bit) memory modules

Note: The AMD-760 MPX requires a portion of

memory to be reserved for PCI devices.

Allocation for these devices is dependent on

the number of PCI devices installed, and option

ROM for each device. Common configurations

will see 3.5GB to 3.8GB of available memory.

Integrated SCSI (manufacturing option)

• Adaptec AIC-7902W or AIC-7899 dual-

channel controller

• Ultra320/Ultra160 SCSI with 320/160MB/sec

throughput per channel (64-bit 66MHz)

• Channel A and Channel B –

68-pin connectors

• (ZCR) Zero Channel RAID Ready

Integrated Video (Manufacturing option)

• ATI RAGE XL graphics controller

• 8MB frame buffer (SDRAM)

Integrated LAN

• Fast Ethernet and Gigabit Ethernet controllers

-Intel 82545EM 10/100/1000Mbps controller

(64-bit 66MHz)

-Intel 82551QM 10/100/100Mbps controller

(32-bit 33MHz)

Hardware Monitoring

• Winbond W83782D hardware monitoring

ASIC

• CPU temperature/voltage monitoring

• 3-pin fan monitoring headers

http://www.TYAN.com

Integrated PCI IDE

• Dual-channel master mode

• Supports up to four IDE devices

• Support for ATA-100/66/33 IDE and ATAPI

compliant devices

Expansion Slots

• One AGP Pro 110 slot; supports 4X/2X AGP

• Two 64-bit 66MHz* (3.3V) and three 32-bit

33MHz (5V) PCI slots

• Total of six usable slots

Integrated I/O

• One floppy connector supports up to two

drives

• Two 9-pin 16550-based serial ports (one via

cable)

• One 25-pin SPP/ECP/EPP parallel port

• PS/2 keyboard and mouse ports

• Two USB ports and two front side USB

headers)

BIOS

• PhoenixBIOS 4.0 revision 6.0 on 4Mbit

Flash ROM

• PXE boot and SMBIOS v2.3.1 support

• BIOS Boot Specification v1.01 (BBS) support

• Boot to USB (Mass Storage Class) support

• ACPI v1.0 support

• Universal Console Redirect (UCR) support

• Power on after AC failure control

Regulatory

• FCC DoC (Declaration of Conformity)

• European CE (Declaration of Conformity)

Form Factor

• Extended ATX footprint (13” x 12”)

• ATX12V/EPS12V dual use power connectors*

• Stacked parallel (one), serial (one) and VGA

(one) connectors

• Stacked USB (two) connectors

• Stacked PS/2 keyboard and mouse

connectors

• Side-by-side RJ-45 LAN (two) connectors

with LEDs

*Warning: The S2469 does NOT support

ATXGES or ATX2.X power supplies.

1.2 Software Specifications

OS (Operating System) Support

•Microsoft Windows NT 4 Service Pack 6A

•Microsoft Windows 2000

•Microsoft Windows XP

TYAN reserves the right to add support or

discontinue support for any OS with or

without notice.

*Due to the tight PCI 66MHz timing of the AMD-760 MPX chipset, it may be necessary to set the

bus to 33MHz when using multiple PCI cards. For more information, refer to the AMD 760

System Controller Datasheet (PID# 24416) on the AMD website: www.amd.com.

http://www.TYAN.com

Chapter 2: Board Installation

Precaution: The Thunder K7X Pro supports ATX12V and EPS12V power supplies (24-pin/8-pin)

and will not operate with any other types. Refer to section 2.21 for instructions on installing

ATX12V and EPS12V power supplies.

Do not use ATX 2.x or ATXGES power supplies as they will damage the board and void your

warranty.

Installation

You are now ready to install your motherboard. The mounting hole pattern of the Thunder K7X

Pro matches the E-ATX (Extended ATX) system board specifications. Your chassis should

support a standard E-ATX motherboard form factor.

How to install our products right… the first time

The first thing you should do is read this user’s manual. It contains important information that will

make configuration and setup much easier. Here are some precautions you should take when

installing your motherboard:

(1) Ground yourself properly before removing your motherboard from the antistatic bag.

Unplug the power from your computer power supply and then touch a safely grounded

object to release static charge (i.e. power supply case). For the safest conditions, TYAN

recommends wearing a static safety wrist strap.

(2) Hold the motherboard by its edges and do not touch the bottom of the board, or flex the

board in any way.

(3) Avoid touching the motherboard components, IC chips, connectors, memory modules,

and leads.

(4) Place the motherboard on a grounded antistatic surface or on the antistatic bag that the

board was shipped in.

(5) Inspect the board for damage.

The following pages include details on how to install your motherboard into your chassis, as well

as installing the processor, memory, disk drives and cables.

NOTE DO NOT APPLY POWER TO THE BOARD IF IT HAS BEEN DAMAGED

http://www.TYAN.com

2.0 –Board

The following is an image of the S2469 Thunder K7X Pro.

The above photograph is only a representation of the actual board. Because boards may

be updated and go through different revisions, certain components may change and or be

repositioned. The picture above may or may not look exactly like the board you received.

The following page will detail vital components of this board.

http://www.TYAN.com

2.1 –Board Jumpers

The above jumper schematic diagram is representative of the latest board revision

available at the time of this manual’s publishing. The board you have received may or may

not be like the above schematic.

Jumper Legend

Jumper OFF (disconnected)

Jumper ON (connected)

http://www.TYAN.com

2.2 –Jumper Summary

Jumper Number Description Reference Page

J12 Front Panel Connector See below

J15 Chassis Intrusion Header See below

J21 CMOS Reset Page 10

J33 10/100 LAN LED Page 10

J34 RESERVED N/A

J36 USB Header Page 10

J49, J48, J53, J52 Front-side Bus Select 133MHz

or 100MHz Page 10, 11

J80 Onboard SCSI Page 11

J85 Onboard ATI RAGE XL Page 11

J86 Onboard 10/100 Ethernet Page 11

J88 Onboard Gigabit Ethernet Page 11

J92 Primary PCI speed Page 11

J102 GbE Front Panel LED Page 12

J103 RESERVED N/A

J104 RESERVED N/A

J105 RESERVED N/A

2.3 –Front Panel Connector (J12)

Your chassis will usually come with connectors to install onto the motherboard, such as HDD and

Power LEDs. The Front Panel Connector (J12) has been implemented for such purposes.

2.4 –Chassis Intrusion Header (J15)

Certain chasses have a switch that detects whether or not they are being opened. This switch

connects to the Chassis Intrusion Header to sound an alarm when the chassis is being opened

without authorization. Simply connect the two-pin switch to the J15 header to enable.

http://www.TYAN.com

2.5 –CMOS Reset (J21)

Clear CMOS

Default

You can reset the CMOS settings in case an incorrect setting causes system

instability, you have forgotten your system/setup password, or have just flashed

your BIOS by using these jumpers.

-Power off system, disconnect power supply from motherboard

-Set jumper J21 to Clear CMOS

-Wait about 5 seconds

-Set jumper J21 to Default

2.6 –10/100Mbit LAN LED (J33)

This header is provided as a visual alert of when the on-board Ethernet port are

active. Simply connect up to two 2-pin LEDs to the LAN LED header for active

monitoring of the on-board Ethernet port.

2.7 –USB Header (J36)

Standard USB connector wire colors:

VCC = Red

Data + = White

Data -= Green

GND = Black

Note: Plugging in the USB connector incorrectly can result in damaging

the USB device and/or the motherboard.

The Front-side USB header is designed for chassis are support front-side

USB. TYAN does not provide these cables.

2.8 –Front-side Bus Select 133MHz (DEFAULT)

J49

J48

J53

J52

Depending on the processor you have, you may need to adjust the

processor Front Side Bus speed in order to have the processors operate

correctly.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere TYAN Hauptplatine Handbücher

TYAN

TYAN TOMCAT K8E-SLI Bedienungsanleitung

TYAN

TYAN S8036 Bedienungsanleitung

TYAN

TYAN TIGER GC-SL Bedienungsanleitung

TYAN

TYAN TOMCAT K8E Bedienungsanleitung

TYAN

TYAN Tomcat i875P S5102 Bedienungsanleitung

TYAN

TYAN TRINITY KT400 Bedienungsanleitung

TYAN

TYAN TRINITY K7 Bedienungsanleitung

TYAN

TYAN Thunder HEsl S2567 Bedienungsanleitung

TYAN

TYAN TIGER I7520SD Bedienungsanleitung

TYAN

TYAN TOMCAT I815EF Bedienungsanleitung

TYAN

TYAN TOMCAT I II Bedienungsanleitung

TYAN

TYAN Tiger MP S2460 Bedienungsanleitung

TYAN

TYAN S7063 Bedienungsanleitung

TYAN

TYAN TIGER LE Bedienungsanleitung

TYAN

TYAN S7086 Bedienungsanleitung

TYAN

TYAN S7053 Bedienungsanleitung

TYAN

TYAN S5221 Bedienungsanleitung

TYAN

TYAN S5548GM4NED83-4T Bedienungsanleitung

TYAN

TYAN Tempest i5400XT S5396 Bedienungsanleitung

TYAN

TYAN Tempest i5400XL Bedienungsanleitung

TYAN

TYAN TYAN S1572 ATX Bedienungsanleitung

TYAN

TYAN TIGER K8W Bedienungsanleitung

TYAN

TYAN TIGER I7322DP Bedienungsanleitung

TYAN

TYAN TRINITY 100AT Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung