TYAN GA88-B5631 Kurzanleitung

GA88-B5631

Service Engineer’s Manual

PREFACE

This publication, including all photographs, illustrations, and software, is

Neither this manual, nor any material contained herein, may be reproduced without

written consent of manufacturer.

reserved. TYAN®is a registered trademark of MITAC COMPUTING TECHNOLOGY

CORPORATION.

Version 1.0

Disclaimer

Information contained in this document is furnished by MiTAC Computer

Corporation and has been reviewed for accuracy and reliability prior to printing.

TYAN®assumes no liability whatsoever, and disclaims any express or implied

warranty, relating to sale and/or use of TYAN®products including liability or

warranties relating to fitness for a particular purpose or merchantability. TYAN®

retains the right to make changes to produce descriptions and/or specifications at

any time, without notice. In no event will TYAN®be held liable for any direct or

indirect, incidental or consequential damage, loss of use, loss of data or other

malady resulting from errors or inaccuracies of information contained in this

document.

Trademark Recognition

All registered and unregistered trademarks and company names contain- -ed in

this manual are property of their respective owners including, but not limited to the

following.

TYAN®is a trademark of MiTAC Computer Corporation.

Intel®is a trademark of Intel Corporation.

AMI®, AMIBIOS®and combinations thereof are trademarks of AMI Technologies.

Microsoft®, Windows®are trademarks of Microsoft Corporation.

Winbond®is a trademark of Winbond Electronics Corporation.

Portable Document Format (PDF) is a trademark of Adobe Corporation.

FCC Declaration

Notice for the USA

Compliance Information Statement (Declaration of Conformity

Procedure) DoC FCC Part 15: This device complies with part 15 of the

FCC Rules

This device complies with Part 15 of the FCC Rules. Operation is subject

to the following conditions:

·This device must not cause harmful interference.

·This device must accept any interference received, including interference that may

cause undesirable operation.

This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his

own expense.

Notice for Canada

This Class A digital apparatus complies with Canadian ICES-003. Cet

appareil numérique de la Classe A est conforme àla norme NMB-003

du Canada.

Notice for Europe (CE Mark)

This product is in conformity with the Council

Directive 2004/108/EC.

CAUTION: Lithium battery included with this board. Do not puncture,

mutilate, or dispose of battery in fire. There will be danger of explosion if

battery is incorrectly replaced. Replace only with the same or equivalent

type recommended by manufacturer. Dispose of used battery according

to manufacturer instructions and in accordance with your local regulations.

About this Manual

This Manual is intended for experienced users and integrators with

hardware knowledge of personal computers.

It is aimed to provide you with instructions on installing your TYAN

GA88-B5631.

How this guide is organized

This guide contains the following parts:

Chapter 1: Overview

This chapter give an introduction to the GA88-B5631 barebones, standard parts

list, and accessories. describes the external components, gives a table of key

Chapter2: Setting Up

This chapter Covers procedures on installing the CPU, memory modules, add

on card and hard drives. Give an overview about the GA88-B5631 barebone

from an overall angle.

Chapter 3: Replacing the Pre-installed Components

This chapter covers the removal and replacement procedures for pre-installed

components.

Chapter 4: Installing GPU Card

This chapter introduce how to installing the GPU Card and list how many kinds GPU

Cards are suitable for GA88-B5631 chassis.

Chapter 5: Mainboard Information

This chapter lists the hardware setup procedures that you need to abide by when

installing system components. It includes description of the jumpers and connectors

on the motherboard.

Chapter6: BIOS Setup

This chapter describes the Petitboot menu program. The menu program lets you

modify basic configuration settings. The settings are then stored in a NVRAM

partition that retains the information even when the power is turned off.

Chapter 7: Diagnostics

This chapter introduces the Hostboot initial program loads (IPLs) progress codes The

table describes the type of checkpoints that may occur during the IPLs portion of the

Hostboot: BIOS codes and technical terms to provide better service for the

customers.

Appendix:

This chapter provides the cable connection table, the FRU parts list for reference of

system setup, and technical support in case a problem arises with your system.

Safety and Compliance Information

Before installing and using TYAN GA88-B5631, take note of the following

precautions:

·Read all instructions carefully.

·Do not place the unit on an unstable surface, cart, or stand.

·Do not block the slots and opening on the unit, which are provided for

ventilation.

·Only use the power source indicated on the marking label. If you are not sure,

contact the power company.

·The unit uses a three-wire ground cable, which is equipped with a third pin to

ground the unit and prevent electric shock. Do not defeat the purpose of this

pin. If your outlet does not support this kind of plug, contact your electrician

to replace your obsolete outlet.

·Do not place anything on the power cord. Place the power cord where it will

not be in the way of foot traffic.

·Follow all warnings and cautions in this manual and on the unit case.

·Do not push objects in the ventilation slots as they may touch high voltage

components and result in shock and damage to the components.

·When replacing parts, ensure that you use parts specified by the

manufacturer.

·When service or repairs have been done, perform routine safety checks to

verify that the system is operating correctly.

·Avoid using the system near water, in direct sunlight, or near a heating

device.

·Cover the unit when not in use.

Safety Information

Retain and follow all product safety and operating instructions provided

with your equipment. In the event of a conflict between the instructions in

this guide and the instructions in equipment documentation, follow the

guidelines in the equipment documentation.

Observe all warnings on the product and in the operating instructions. To

reduce the risk of bodily injury, electric shock, fire and damage to the

equipment, observe all precautions included in this guide.

You must become familiar with the safety information in this guide before

you install, operate, or service TYAN products.

Symbols on Equipment

Caution. This symbol indicates a potential hazard.

The potential for injury exists if cautions are not

observed. Consult equipment documentation for

specific details.

Caution. Slide-mounted equipment is not to be used

as a shelf or a work space.

Warning. This symbol indicates the presence of

hazardous energy circuits or electric shock hazards.

Refer all servicing to qualified personnel.

Warning. This symbol indicates the presence of a hot

surface or hot component. If this surface is contacted,

the potential for injury exists.

To reduce risk of injury from a hot component, allow

the surface to cool before touching.

General Precautions

·Follow all caution and warning instructions marked on the equipment and

explained in the accompanying equipment documentation.

Machine Room Environment

·This device is for use only in a machine room or IT room.

 ·Make sure that the area in which you install the system is properly

ventilated and climate-controlled.

·Ensure that the voltage and frequency of your power source match the

voltage and frequency inscribed on the electrical rating label of the

equipment.

·Do not install the system in or near a plenum, air duct, radiator, or heat

·Never use the product in a wet location.

Equipment Chassis

·Do not block or cover the openings to the system.

·Never push objects of any kind through openings in the equipment.

Dangerous voltages might be present.

·Conductive foreign objects can produce a short circuit and cause fire,

electric shock, or damage to your equipment.

·Lift equipment using both hands and with your knees bent.

Equipment Racks

To avoid injury or damage to the equipment:

·Observe local occupational health and safety requirements and guidelines

for manual materials handling.

·Do not attempt to move a rack by yourself; a minimum of two people are

needed to move a rack.

·Do not attempt to move a fully loaded rack. Remove equipment from the

rack before moving it.

·Do not attempt to move a rack on an incline that is greater than 10 degrees

from the horizontal.

·Make sure the rack is properly secured to the floor or ceiling.

·Make sure the stabilizing feet are attached to the rack if it is a single-rack

installation.

·Make sure racks are coupled together if it is a multiple-rack installation.

·Make sure the rack is level and stable before installing an appliance in the

rack.

·Make sure the leveling jacks are extended to the floor.

·Make sure the full weight of the rack rests on the leveling jacks.

·Always load the rack from the bottom up. Load the heaviest component in

the rack first.

·Make sure the rack is level and stable before pulling a component out of the

rack.

·Make sure only one component is extended at a time. A rack might become

unstable if more than one component is extended.

To avoid damage to the equipment:

·The rack width and depth must allow for proper serviceability and cable

management.

·Ensure that there is adequate airflow in the rack. Improper installation or

restricted airflow can damage the equipment.

·The rack cannot have solid or restricted airflow doors. You must use a

mesh door on the front and back of the rack or remove the doors to ensure

adequate air flow to the system.

·If you install the Model in a rack, do not place equipment on top of the unit.

It will cause restricted airflow and might cause damage to the equipment.

·Make sure the product is properly matted with the rails. Products that are

improperly matted with the rails might be unstable.

·Verify that the AC power supply branch circuit that provides power to the

rack is not overloaded. This will reduce the risk of personal injury, fire, or

damage to the equipment. The total rack load should not exceed 80 percent

of the branch circuit rating. Consult the electrical authority having jurisdiction

over your facility wiring and installation requirements.

·Verify that the AC power supply branch circuit that provides power to the

rack is not overloaded. This will reduce the risk of personal injury, fire, or

damage to the equipment. The total rack load should not exceed 80 percent

of the branch circuit rating. Consult the electrical authority having jurisdiction

over your facility wiring and installation requirements.

·Verify that the AC power supply branch circuit that provides power to the

rack is not overloaded. This will reduce the risk of personal injury, fire, or

damage to the equipment. The total rack load should not exceed 80 percent

of the branch circuit rating. Consult the electrical authority having jurisdiction

over your facility wiring and installation requirements.

·When use 100V-127VAC input: The system does not support redundant

PSU operation if the total system load exceeds 20A.

Equipment Power Cords

·Use only the power cords and power supply units provided with your

system. The system might have one or more power cords.

·Plug the power cord into a grounded (earthed) electrical outlet that is easily

accessible at all times.

·In all European electrical environments, you must ground the Green/Yellow

tab on the power cord. If you do not ground the Green/Yellow tab, it can

cause an electrical shock due to high leakage currents.

·Do not place objects on AC power cords or cables. Arrange them so that no

one might accidentally step on or trip over them.

·Do not pull on a cord or cable. When unplugging from the electrical outlet,

grasp the cord by the plug.

·To reduce the risk of electrical shock, disconnect all power cords before

servicing the appliance.

Equipment Batteries

·The system battery contains lithium manganese dioxide. If the battery pack

is not handled properly, there is risk of fire and burns.

·Do not disassemble, crush, puncture, short external contacts, or dispose of

the battery in fire or water.

·Do not expose the battery to temperatures higher than 60°C (140°F).

·The system battery is not replaceable. If the battery is replaced by an

incorrect type, there is danger of explosion. Replace the battery only with a

spare designated for your product.

·Do not attempt to recharge the battery.

·Dispose of used batteries according to the instructions of the manufacturer.

Do not dispose of batteries with the general household waste. To forward

them to recycling or proper disposal, use the public collection system or return

them to TYAN, your authorized TYAN partner, or their agents.

Equipment Modifications

·Do not make mechanical modifications to the system. TYAN is not

responsible for the regulatory compliance of TYAN equipment that has been

modified.

Equipment Repairs and Servicing

·The installation of internal options and routine maintenance and service of

this product should be performed by trained service technician/personnel who

are knowledgeable about the procedures, precautions, and hazards

associated with equipment containing hazardous energy levels.

·Do not exceed the level of repair specified in the procedures in the product

documentation. Improper repairs can create a safety hazard.

·Allow the product to cool before removing covers and touching internal

components.

·Remove all watches, rings, or loose jewelry when working before removing

covers and touching internal components.

·Do not use conductive tools that could bridge live parts.

·Use gloves when you remove or replace system components; they can

become hot to the touch.

·If the product sustains damage requiring service, disconnect the product

from the AC electrical outlet and refer servicing to an authorized service

provider. Examples of damage requiring service include:

–The power cord, extension cord, or plug has been damaged.

–Liquid has been spilled on the product or an object has fallen into the

product.

–The product has been exposed to rain or water.

–The product has been dropped or damaged.

–The product does not operate normally when you follow the operating

instructions.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere TYAN Server Handbücher

TYAN

TYAN Transport GT20 B5151 Bedienungsanleitung

TYAN

TYAN Transport SX TN70E-B8026 Kurzanleitung

TYAN

TYAN TN70-B7016 Kurzanleitung

TYAN

TYAN GT24B-B7076 Kurzanleitung

TYAN

TYAN YR190-B7018 Bedienungsanleitung

TYAN

TYAN B7058Y190X2 Kurzanleitung

TYAN

TYAN Transport GT20 B3870 Bedienungsanleitung

TYAN

TYAN Transport GX18 Bedienungsanleitung

TYAN

TYAN Tank FT48 B5382 Bedienungsanleitung

TYAN

TYAN MicroServer FM65-B5531 Kurzanleitung

TYAN

TYAN TN71-BP012 Bedienungsanleitung

TYAN

TYAN TS65A-B8036 Kurzanleitung

TYAN

TYAN FT48-B8812 Kurzanleitung

TYAN

TYAN Transport GT20 B5350 Service Bedienungsanleitung

TYAN

TYAN GT24 B5501 Bedienungsanleitung

TYAN

TYAN TN70-B7066 Kurzanleitung

TYAN

TYAN Transport GX21 B2735 Bedienungsanleitung

TYAN

TYAN FT83-B7119 Kurzanleitung

TYAN

TYAN Transport GT24 B3992 Bedienungsanleitung

TYAN

TYAN Transport GX28 B2881 Bedienungsanleitung

TYAN

TYAN TS65-B7126 Kurzanleitung

TYAN

TYAN TN76-BP016 Bedienungsanleitung

TYAN

TYAN Transport VX50 Bedienungsanleitung

TYAN

TYAN Tank GT25 B5381 Kurzanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung