TYAN Transport VX50 Bedienungsanleitung

Transport VX50

Service Engineer’s Manual

Documentpart number: D1652-110

Preface

This publication, including all photographs, illustrations, and soft-

ware, is protected under international copyright laws, with all rights

reserved. Neither this manual, nor any material contained herein,

may be reproduced without written consent of the manufacturer.

Version 1.00

Disclaimer

Information contained in this document is furnished by TYAN

Computer Corporation and has been reviewed for accuracy and reli-

ability prior to printing. TYAN assumes no liability whatsoever, and

disclaims any express or implied warranty, relating to sale and/or

use of TYAN products including liability or warranties relating to fit-

ness for a particular purpose or merchantability. TYAN retains the

right to make changes to product descriptions and/or specifications

at any time, without notice. In no event will TYAN be held liable for

any direct or indirect, incidental or consequential damage, loss of

use, loss of data or other problem resulting from errors or inaccura-

cies of information contained in this document.

Trademark recognition

All registered and unregistered trademarks and company names

contained in this manual are property of their respective owners

including, but not limited to the following.

TYAN, Tyan Thunder K8QW Pro S4881, and VX50 B4881 are

trademarks of TYAN Computer Corporation.

AMD, Opteron, and combinations thereof are trademarks of

Advanced Micro Devices Corporation.

AMI, AMIBIOS, and combinations thereof are trademarks of AMI

Software Incorporated.

Microsoft Windows is a trademark of Microsoft Corporation.

IBM, PC, AT and PS/2 are trademarks of IBM Corporation.

Winbond is a trademark of Winbond Electronics Corporation.

Federal Communications Commission

Notice for the USA Compliance Information State-

ment (Declaration of Conformity Procedure) DoC

FCC Part 15: This device complies with part 15 of the

FCC Rules

Operation is subject to the following conditions:

1) This device may not cause harmful interference, and

2) This device must accept any interference received including inter-

ference that may cause undesired operation. If this equipment does

cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is

encouraged to try one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and the

receiver.

•Plug the equipment into an outlet on a circuit different from

that of the receiver.

Consult the dealer or an experienced radio/television technician for

help.

Notice for Canada

This apparatus complies with the Class B limits for radio interfer-

ence as specified in the Canadian Department of Communications

Radio Interference Regulations. (Cet appareil est conformé aux

norms de Classe B d’interference radio tel que specifie par le Minis-

tere Canadien des Communications dans les reglements d’inter-

férence radio.)

Notice for Europe (CE Mark) This product is in conformity

with the Council Directive 89/336/EEC, 92/31/EEC

(EMC).

CAUTION: Lithium battery included with this board. Do not puncture,

mutilate, or dispose of battery in fire. Danger of explosion if battery

is incorrectly replaced. Replace only with the same or equivalent

type recommended by manufacturer. Dispose of used battery

according to manufacturer instructions and in accordance with your

local regulations.

iii

About this manual

This manual provides you with instructions on installing your VX50

B4881, and consists of the following sections:

Chapter 1 – Overview:

Provides an introduction to the VX50 B4881 barebones, shows a

packing list, describes the external components, shows tables of key

components, and provides a block diagram of the system.

Chapter 2 – Setting up:

Covers procedures on installing the CPUs, memory modules,

optional PCI card, and hard drives.

Chapter 3 – Replacing pre-installed components:

Covers removal and replacement procedures for pre-installed com-

ponents.

Appendix:

Provides detailed specifications, maintenance and troubleshooting

procedures, an explanation of BIOS, and technical diagrams.

Safety information

Before installing and using the VX50 B4881, take note of the follow-

ing precautions:

•Read all instructions carefully.

•Do not place the unit on an unstable surface, cart, or stand.

•Do not block the slots or openings on the unit which are

provided for ventilation.

•Only use the power source indicated on the marking label.

If you are not sure about your power source, contact the

power company.

•The unit uses a three-wire grounded cable, which is sup-

plied with a third pin to ground the unit and prevent electric

shock. Do not defeat the purpose of this pin. If your outlet

does not support this type of plug, contact an electrician to

replace the obsolete outlet.

•Do not place anything on the power cord. Place the power

cord where it will not be stepped on.

•Follow all warnings and cautions in this manual and on the

unit case.

•Do not push objects in the ventilation slots, as they may

touch high voltage components and result in shock and

damage to the components.

•When replacing parts, ensure that you use parts specified

by the manufacturer.

•When service or repairs have been carried out, perform

routine safety checks to verify that the system is operating

correctly.

•Avoid using the system near water, in direct sunlight, or

near a heating device.

•Cover the unit when not in use.

•Disassembly of this unit should not be attempted by

unqualified persons. When the chassis cover is removed

there is a danger of electric shock and risk of damage to

the system.

•Do not attempt to lift or move this product alone. When

moving this product, at least two people should lift it onto a

suitable trolley or cart. When bolting the product into a

rack, two people should hold the device in place while a

third person bolts the device securely to the rack.

Table of Contents

Chapter 1: Overview

1.1 About the VX50 B4881 ...................................................... 1

1.2 Features............................................................................. 2

1.3 Unpacking .......................................................................... 3

1.3.1 Box contents ................................................................ 3

1.3.2 Accessories ................................................................. 4

1.3.3 Opening the box .......................................................... 5

1.4 About the product............................................................... 6

1.4.1 System front view and front panel ............................... 6

1.4.2 System rear view ......................................................... 6

1.4.3 System internal view.................................................... 7

1.4.4 LED control panel ........................................................ 8

1.4.5 Rear LEDs ................................................................... 8

1.4.6 S4881 motherboard block diagram.............................. 9

1.4.7 M4881 CPU board block diagram.............................. 10

1.4.8 ID LED function.......................................................... 10

1.4.9 Fan header locations ................................................. 11

Chapter 2: Setting up

2.1 Before you begin.............................................................. 13

2.1.1 Work area .................................................................. 13

2.1.2 Tools .......................................................................... 13

2.1.3 Precautions................................................................ 14

2.2 Installing motherboard components................................. 15

2.2.1 Removing the chassis cover...................................... 15

2.2.2 Installing CPUs and heatsinks ................................... 16

2.2.3 Installing memory....................................................... 18

2.2.4 Installing the M4881 CPU expansion board .............. 20

2.2.5 Installing PCI-X cards ................................................ 22

2.3 Installing hard drives ........................................................ 22

2.3.1 Installing a storage backplane ................................... 23

2.3.2 Installing SATA/SCSI hot swap drives....................... 25

2.3.3 Installing internal hard drives ..................................... 26

2.4 Rack mounting ................................................................. 28

2.5 Standalone....................................................................... 32

2.6 Fitting the front door assembly......................................... 33

Chapter 3: Replacing pre-installed components

3.1 Introduction ...................................................................... 35

3.2 Replacing motherboard components ............................... 35

3.2.1 Disconnecting all motherboard cables....................... 35

3.2.2 Replacing the CPU expansion board......................... 39

3.2.3 Replacing the motherboard ....................................... 40

3.3 Replacing the slim DVD-ROM drive................................. 40

3.4 Replacing the floppy disk drive ........................................ 42

3.5 Replacing the SATA/SCSI backplane.............................. 43

3.6 Replacing power supplies ................................................ 44

3.7 Replacing cooling fans..................................................... 45

Appendix

BIOS Notice ............................................................................ 47

Introduction .......................................................................... 47

Hardware monitor submenu................................................. 47

Integrated devices submenu................................................ 48

Remote access configuration submenu............................... 49

M1207 Jumper Setting ............................................................ 50

PW1 and PW2 big 4-pin out................................................. 50

SW5 dip switch setting......................................................... 50

SCSI ID settings................................................................... 51

Technical support.................................................................... 52

Help resources..................................................................... 52

Returning merchandise for service ...................................... 52

Chapter 1: Overview 1

Chapter 1: Overview

1.1 About the VX50 B4881

Congratulations on your purchase of the VX50 B4881, rack

mountable or standalone, barebone system. This product

supports up to 8 AMD Opteron™ 800 series processors and

128 GB of registered DRAM, offering exceptional computing

power and simultaneous support of 32-bit and 64-bit applica-

tions. The following models and processors are supported:

Hot swap SATA or SCSI hard disk drives provide convenient

and resilient data storage capacity, and on-board Gigabit

Ethernet ports ensure high-speed data communication.

The rugged, rack mountable design includes eight HDD bays

and one slim DVD-ROM bay.

WARNING: This product is very heavy and should not

be lifted by a single person. When install-

ing this product in a rack, we recommend

that at least two people lift the server while

a third person guides it into place and

tightens the fixings. Always use a suitable

trolley or cart to transport the device.

Model Number Processor support

B4881 V50S4H -4P / B4881 V50U8H -4P Up to 4 P

B4881 V50S4H -8P / B4881 V50U8H -8P Up to 8 P

1.2 Features

2 Chapter 1: Overview

1.2 Features

Enclosure

• Industry standard pedestal or 19-inch

rack mountable, 5U chassis

• (1) slim DVD-ROM drive bay

• (1) standard FDD bay

• (3) 5.25-inch device bays

• Dimensions:

- 26.8 x 16.7 x 8.7-inch (5U)

- 680 x 425 x 220 mm

• B4881V50S4H

- (4) hot swap SATA HDD bays

- (4) internal HDD bays (upgradable

to hot swap bays)

• B4881 V50U8H

- (8) hot swap SCSI HDD bays

Storage Controller

• (2) dual port SATA II controllers

integrated in NVIDIA nForce4 Pro chip

• Support for up to four SATA HDDs

• Supports 3 Gb/s per port, 1.5 Gb/s in each

direction per channel

• Support for RAID 0, 1, 0+1, and NVIDIA

Morphing RAID

Motherboard

• Tyan Thunder K8QW Pro S4881

• SSI EEB 3.5 footprint (13 x 16-inch)

CPU board (for 8P configuration)

• Tyan M4881

• 13 x 12-inch

Processors

• Support for up to eight AMD®

Opteron™ 800 series processors.

Networking

• (2) Gbit Ethernet ports (Broadcom®

BCM5704 dual port controller)

Chipset

• NVIDIA nForce4 Professional + AMD-

8131 HyperTransport PCI-X tunnel

• Winbond W83627HF Super I/O chip

• ADT7468 hardware monitor IC

BIOS

• Phoenix 8Mbit LPC Flash ROM

• Serial Console Redirect

• USB device boot

• ACPI 2.0 power management support

Memory

• (16) 184-pin 2.5V DDR DIMM

sockets on S4881 motherboard

• (16) 184-pin 2.5V DDR DIMM

sockets on M4881 CPU board

• Up to 128 GB of registered, ECC

DDR400/333/266 memory

Power supply

• Redundant power supply modules (4-8).

• Total power 1140W (4P), 1620W (8P)

• AC input 100-230 VAC full range

Video

•ATI

® Rage™ XL PCI Graphics controller

• 8 MB Frame Buffer video memory

Expansion slots

• (2) x16 PCI Express slots (one with x4

signal)

• (2) Independent 64-bit PCI-X bus

• (1) 64-bit 133 MHz (3.3V) PCI-X slot

• (2) 64-bit 100 MHz (3.3V) PCI-X slot

Server Management

• Automatic fan speed control

• Chassis intrusion alert

• Tyan Server Management Support

• Tyan SMDC, IPMI 2.0 compliant remote

server management kit (option)

Back I/O ports

• PS/2 mouse and keyboard ports

• (2) RJ-45 10/100/100BaseT with

activity LED

• (2) USB 2.0 ports

• (1) 9-pin UART serial port

• (1) 15-pin VGA port

Front panel

• (2) USB 2.0 ports

• LED indicators (power, LAN x2, HDD

activity, ID)

• Switches (power, reset, ID)

Environment

• 5 ~ 35 ºC operating environment

• -40 ~ 70 ºC storage environment

Regulatory

• FCC Class B (declaration of conformity)

• CE (declaration of conformity)

Inhaltsverzeichnis

Andere TYAN Server Handbücher

TYAN

TYAN GT62F-B5630 Kurzanleitung

TYAN

TYAN Transport VX50 (B4985 Series) Bedienungsanleitung

TYAN

TYAN Transport GT20 B5151 Bedienungsanleitung

TYAN

TYAN FT48 B7025 Bedienungsanleitung

TYAN

TYAN GA80-B7081 Kurzanleitung

TYAN

TYAN Tank FT48 B5382 Bedienungsanleitung

TYAN

TYAN B5102 Bedienungsanleitung

TYAN

TYAN GN70-B8236-HE Kurzanleitung

TYAN

TYAN Transport TA26 B2932 Bedienungsanleitung

TYAN

TYAN TS75A-B8252 Kurzanleitung

TYAN

TYAN Transport TA26 B3992 Bedienungsanleitung

TYAN

TYAN TN76-BP016 Bedienungsanleitung

TYAN

TYAN TA77-B7061 Kurzanleitung

TYAN

TYAN FT48 Kurzanleitung

TYAN

TYAN Transport GX18 B3095 Bedienungsanleitung

TYAN

TYAN FT72 B7015 Bedienungsanleitung

TYAN

TYAN TN73-B8037 Kurzanleitung

TYAN

TYAN TN76A-B8242 Kurzanleitung

TYAN

TYAN Tank GT20 B5375 Bedienungsanleitung

TYAN

TYAN YR190-B8228 Bedienungsanleitung

TYAN

TYAN YR190-B8238 Kurzanleitung

TYAN

TYAN B7086T70BV12HR Kurzanleitung

TYAN

TYAN GT62B-B5539 Kurzanleitung

TYAN

TYAN FT77-B7015 Kurzanleitung

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung