Tyco FASTFLEX FB Bedienungsanleitung

FASTFLEX

Model FB Flexible Braided Hose

Page 1 of 4 NOVEMBER 2014 TFP730

Worldwide

Contacts

www.tyco-ﬁre.com

Technical

Data

Approvals

VdS Approved

(Refer to Table A for specic laboratory

approvals and the approvals apply to

the service conditions indicated in the

Design Criteria sections.)

CSTB accepted for all models and

assembly lengths.

Inlet Connections (Ref Fig. 1)

ISO 7-R 1

Outlet Connections (Ref Fig. 2)

1/2 inch NPT

3/4 inch NPT

Nominal Assembly Lengths

Refer to Table A

Construction (Ref. Fig. 1)

The Inlet Nipple is mild steel, and the

Flexible Hose is SS AISI 304. The

Sprinkler Reducer is mild steel. The

Reducer Bracket, Bar Fixing Clamps,

and Support Bar are pressed steel.

Design Criteria

The TYCO FASTFLEX Model FB Flexible

Braided Hose is VdS Listed and used

with pendent sprinklers. The following

paragraph provides the design criteria

unique to VdS Approval listing.

VdS Listing Design Criteria

• Wet-pipe systems only

• Minimum bend radius of 55 mm

• Maximum service pressure of 16

bar

• Pendent sprinklers with nominal

K57, K80, or K115

• Maximum ambient temperature of

107°C

General

Description

The TYCO FASTFLEX Model FB Flex-

ible Braided Hose is a unique sprinkler

drop assembly comprised of a stainless

steel exible hose a swivel inlet nipple,

a sprinkler reducer, and lightweight

ceiling bracket components. (Refer to

Figure 1.)

The FASTFLEX Model FB Flexible

Braided Hose can be installed in false

ceilings without cutting and thread-

ing pipes associated with installing a

drop, arm-over, and elbow. It provides

easier maneuverability around ducts

and trays in congested spaces and for

unusual ceiling types and curved plas-

terboard ceilings. The FASTFLEX Model

FB Flexible Braided Hose makes it pos-

sible to test and charge the system with

water before the ceiling grid is installed.

Once the ceiling grid is in position, the

hoses can be reshaped to suit the nal

sprinkler location without draining the

system.

The FASTFLEX Model FB Flexible

Braided Hose hoses are for use on wet

pipe sprinkler systems only.

NOTICE

The TYCO FASTFLEX Model FB Flexible

Braided Hose ﬂexible sprinkler hoses

described herein must be installed

and maintained in compliance with

this document and with the applicable

standards recognized by the Approval

agency, in addition to the standards of

any other authorities having jurisdiction.

Failure to do so may impair the perfor-

mance of these devices.

The owner is responsible for main-

taining their fire protection system

and devices in proper operating con-

dition. Contact the installing contrac-

tor or product manufacturer with any

questions.

Approved Ceiling Systems

FASTFLEX Model FB Flexible Braided

Hose is approved for use only in the

following manufacturers suspended

ceilings listed below on the condition

that the prole is based on a T-shaped

prole:

AMF

Odenwald

Richter

Armstrong

Rigips

Knauf

Chicago Metallic

Durlum

Geipel

Gema Armstrong

Suckow & Fischer

USG Donn

Daldrop & Dr. Huber

Rockfon Pagos

VdS Friction Loss

For compensation of pressure

loss, the nominal assembly length

is to be multiplied by 10. The re-

sulting length will provide pressure

drop in equivalent length DN25

(33,7 x 3,25 mm) metal tube per EN

10255.

• Add 2,3 m when using a 90° sprin-

kler reducer.

TFP730

Page 2 of 4

Installation

The TYCO FASTFLEX Model FB

Flexible Braided Hose, as shown in

Figure 1, must be installed in accor-

dance with this section.

NOTICE

Flexible Braided Hoses are intended

only to connect sprinklers directly to

system piping (refer to Figure 1). Flex-

ible Hoses cannot be joined together

to form longer hoses. Joining Flexible

Hoses together creates an assembly

with unknown performance that has

not been accounted for in system cal-

culations or safe product performance.

Step 1. Review the Design Criteria

section that applies to the approval

agency recognized by the authority

having jurisdiction, as well as Figure 3

that provides Installation Guidance.

Step 2. Determine approximately where

the sprinkler will be located. Mount the

End Brackets to the Support Bar then

slide the End Brackets over the ceiling

grid T-bars. The sprinkler should be

located as close to the center of the dis-

tance between the ceiling grid T-bars

as possible.

Step 3. Hand-tighten the Wings Screws

and the Hex Screws on the End Brack-

ets securing the Support Bar.

Step 4. Attach the Swivel Inlet Nipple

to the Branchline Fitting outlet. (Refer

to Figure 1.) Apply the wrench directly

to the Swivel Inlet Nipple and tighten to

the maximum torque of 35 Nm.

Step 5. Attach the sprinkler to the

Sprinkler Reducer. Place a wrench on

the Sprinkler Reducer to counteract

the tightening torque of the sprinkler

and torque the sprinkler to the recom-

mended torque setting. Refer to the

sprinkler manufacturer’s sprinkler data

sheet for appropriate sprinkler torque

setting, sprinkler wrench, and other

guidance.

Step 6. Bend the Flexible Hose and

place the Sprinkler Reducer to where

the sprinkler will be located. The hose

arc should not be twisted, and the arc

should be as large and smooth as pos-

sible. (Refer to Figures 2 and 3.)

NOTICE

For minimum bend criteria, refer to the

Design Criteria section that applies to

the approval agency recognized by the

authority having jurisdiction.

A bend radius smaller than pro-

vided by the minimum bend criteria

may adversely effect the friction loss

speciﬁcations stated by the approval

laboratory.

Step 7. Slide the Reducer Bracket over

the Sprinkler Reducer end of the Flex-

ible Sprinkler Hose and clip over the

Support Bar. Hand-tighten the fastener

on the Reducer Bracket securing the

Reducer Bracket to the Support Bar.

Ensure that the Reducer Bracket fas-

tener is secured to the at surface of

the Sprinkler Reducer.

Step 8. After tightening the Reducer

Bracket fastener, verify that the sprin-

kler is properly located in accordance

with the manufacturer’s instructions.

If not in the proper location, adjust its

position as necessary.

Step 9. Once the sprinkler is in the

proper location, torque all hardware as

follows:

CEILING

GRID

T-BAR

DROP-IN

CEILING

PANEL

SUPPORT

BAR

SYSTEM

BRANCHLINE

SPRINKLER INSTALLED

IN ACCORDANCE WITH

MANUFACTURER'S

INSTRUCTIONS

BRANCHLINE

FITTING

(NOT INCLUDED)

REDUCER

BRACKET WITH

SOCKET HEAD

SCREW

INTEGRATED

HEX STRAIGHT

SPRINKLER

REDUCER

BRAIDED

JACKET

FLEXIBLE

HOSE

BRANCHLINE

FITTING

ISO 7-R 1

THREADED

OUTLET

END BRACKET

WITH WING

SCREW, HEX

SCREW AND

LOCK WASHER

INTEGRATED

KNURLED AND

MALE THREADED

SWIVEL INLET

NIPPLE

600 mm

FIGURE 1

FASTFLEX FLEXIBLE SPRINKLER HOSE

TFP730

Page 3 of 4

NOTE: The End Brackets Wing Screws

must be tightened before tightening the

Reducer Bracket to the Support Bar.

End Bracket

Hex Screws ..........4,5 Nm (min)

End Bracket

Wing Screws ........ 4,5 to 5,7 Nm

Reducer Bracket

Fastener . . . . . . . . . . . . . 2,3 Nm (min)

Care and

Maintenance

The TYCO FASTFLEX Model FB Flex-

ible Braided Hose must be maintained

and serviced in accordance with this

section.

Before closing a re protection system

control valve for inspection or main-

tenance work on the re protection

system that it controls, permission to

shut down the effected re protection

system must rst be obtained from

the proper authorities and all person-

nel who may be affected by this action

must be notied.

Inspection, testing, and maintenance

must be performed as indicated below

and in accordance with the local

requirements and/or national codes.

Any impairment must be immediately

corrected.

The owner is responsible for the inspec-

tion, testing, and maintenance of their

re protection system and devices in

compliance with this document, as well

as with the applicable standards of the

authorities having jurisdiction. Contact

the installing contractor or product

manufacturer with any questions.

After placing a re protection system

in service, notify the proper authorities

and advise those responsible for moni-

toring proprietary and/or central station

alarms.

Automatic sprinkler systems are rec-

ommended to be inspected, tested,

and maintained by a qualied Inspec-

tion Service in accordance with local

requirements and/or national codes.

Limited

Warranty

For warranty terms and conditions, visit

www.tyco-re.com.

Model

Nominal

Length

Maximum

Number of

Bends

700 700 mm 3

1000 1000 mm 3

1200 1200 mm 3

1500 1500 mm 4

2000 2000 mm 4

OUTER

BRAIDED

JACKET

STRAIGHT

SPRINKLER

REDUCER

90°

SPRINKLER

REDUCER

INNER

FLEXIBLE

HOSE

SWIVEL

INLET

NIPPLE

OUTER

BRAIDED

JACKET

INNER

FLEXIBLE

HOSE

SWIVEL

INLET

NIPPLE

ISO 7-R 1

180 mm

ISO 7-R 1

1/2" NPT

3/4" NPT

1/2" NPT

3/4" NPT

FIGURE 2

FASTFLEX FLEXIBLE SPRINKLER HOSE

NOMINAL DIMENSIONS

GLOBAL HEADQUARTERS | 1400 Pennbrook Parkway, Lansdale, PA 19446 | Telephone +1-215-362-0700

TFP730

Page 4 of 4

Route the Model FB Flexible Hose to permit the water to drain back into the branchline or through the

sprinkler reducer.

Ordering

Procedure

Contact your local distributor for avail-

ability. When placing an order, indicate

the full product name and Part Number

(P/N).

Flexible Hose Assembly*

Specify: FASTFLEX Model FB Flexible

Braided Hose Model (specify - refer

to Table A), (specied) length, and

(50 or 90 mm) Bar Fixing Clamps, P/N

(specify):

*The FASTFLEX Model FB Flexible

Braided Hose Assembly includes the

following items:

- Flexible Braided Hose

- Inlet Nipple, ISO 7-R 1

- Straight Sprinkler Reducer, 1/2” NPT

- Reducer Bracket

- End Brackets

- Support Bar

Model with 1/2 inch Straight Reducer:

700 .......................P/N FBS1250700

1000 ......................P/N FBS1251000

1200 ......................P/N FBS1251200

1500 ......................P/N FBS1251500

2000 ......................P/N FBS1252000

Model with 1/2 inch Angled Reducer:

700 .......................P/N FBA125070 0

1000 ......................P/N FBA1251000

1200 ......................P/N FBA1251200

1500 ......................P/N FBA1251500

2000 ......................P/N FBA1252000

Model with 3/4 inch Straight Reducer:

700 .......................P/N FBS3250700

1000 ......................P/N FBS3251000

1200 ......................P/N FBS3251200

1500 ......................P/N FBS3251500

2000 ..................... P/N FBS3252000

Model with 3/4 inch Angled Reducer:

700 .......................P/N FBA3250700

1000 ......................P/N FBA3251000

1200 ......................P/N FBA3251200

1500 ......................P/N FBA3251500

2000 ......................P/N FBA3252000

End Bracket

Specify: FASTFLEX End Bracket, P/N

FENDBRA

Support Bar

Specify: FASTFLEX Support Bar,

(specify) length, (P/N (specify):

700 .....................P/N FSUPBAR0700

1000 ....................P/N FSUPBAR1000

1300 ....................P/N FSUPBAR1300

Reducer Bracket

Specify: FASTFLEX Reducer Bracket,

(specify) size, (P/N (specify):

1/2" ......................P/N FREDBRA050

3/4" ......................P/N FREDBRA075

Model Type

Assembly

Length in

Millimeters

VdS

50 and 90 mm

Bar Fixing Clamp

Sprinkler

Reducer Type

0° 90°

YB25-700 Braided 700 x x

YB25-1000 Braided 1000 x x

YB25-1200 Braided 1200 x x

YB25-1500 Braided 1500 x x

YB25-2000 Braided 2000 x x

x Indicates Listed or Approved as applicable.

NOT PERMITTEDPERMITTED NOT PERMITTEDPERMITTED

TABLE A

FASTFLEX SPRINKLER HOSE ASSEMBLY

MODELS, ASSEMBLY LENGTHS, AND APPROVALS

FIGURE 3

FASTFLEX FLEXIBLE BRAIDED SPRINKLER HOSE

INSTALLATION GUIDANCE

Andere Tyco Bewässerungssystem Handbücher

Tyco

Tyco TY-B Series Bedienungsanleitung

Tyco

Tyco TY-FRL Series Bedienungsanleitung

Tyco

Tyco TY-FRB Series Bedienungsanleitung

Tyco

Tyco ILLUSION Bedienungsanleitung

Tyco

Tyco Rapidresponse LFII Series Bedienungsanleitung

Tyco

Tyco Grinnell F692 DESIGNER Bedienungsanleitung

Tyco

Tyco Central ESFR-25/WilFlow Bedienungsanleitung

Tyco

Tyco FSC 80 K-factor Bedienungsanleitung

Tyco

Tyco DSB-1 Bedienungsanleitung

Tyco

Tyco TY-FRB Series Bedienungsanleitung

Tyco

Tyco RAVEN 5.6K Bedienungsanleitung

Tyco

Tyco ELO-231 Series Bedienungsanleitung

Tyco

Tyco TY3201 Bedienungsanleitung

Tyco

Tyco ESFR-22 Bedienungsanleitung

Tyco

Tyco DS-1 Series Bedienungsanleitung

Tyco

Tyco TY-FRFS Bedienungsanleitung

Tyco

Tyco TY7158 Bedienungsanleitung

Tyco

Tyco TY-B Series Bedienungsanleitung

Tyco

Tyco CC3 Bedienungsanleitung

Tyco

Tyco LFII Series Leitfaden

Tyco

Tyco F08 FIP Bedienungsanleitung

Tyco

Tyco ESFR-1 Bedienungs- und Wartungsanleitung

Tyco

Tyco rapid response LFII Series Bedienungsanleitung

Tyco

Tyco 3002B Bedienungsanleitung

Beliebte Bewässerungssystem Handbücher anderer Marken

Hunter

Hunter Institutional Series Bedienungsanleitung

Cellfast

Cellfast 52-305 Bedienungsanleitung

Tyco Fire Product

Tyco Fire Product Star Galaxy SGQR Bedienungsanleitung

Tyco Fire Product

Tyco Fire Product CENTRAL A Bedienungsanleitung

Oral Care Technologies

Oral Care Technologies Hydro Floss Bedienungsanleitung

Reliable

Reliable F1-300 Bedienungsanleitung

Tyco Fire Product

Tyco Fire Product Gem F892 Bedienungsanleitung

Netafim

Netafim NETBEAT Bedienungsanleitung

Irrigation-Mart

Irrigation-Mart KIT-GK100-RV-B Bedienungsanleitung

Reliable

Reliable F4FR Bedienungsanleitung

OpenSprinkler

OpenSprinkler OSPi Bedienungsanleitung

EINHELL

EINHELL GE-WW 5537 E Bedienungsanleitung

Valley

Valley Bender160 Bedienungsanleitung

Reliable

Reliable F1FR42 Series Bedienungsanleitung

Reliable

Reliable F1FR-300 Bedienungsanleitung

Toro

Toro 730 Series Kurzanleitung

Eden

Eden 97063-EDAMZ Bedienungsanleitung

Tyco Fire Product

Tyco Fire Product CENTRAL ELO-231 Bedienungsanleitung