U-Line H-2590 Bedienungsanleitung
0810 IH-2590PAGE 1 OF 3
1-800-295-5510
uline.com
HEAVY DUTY AUTOMATIC
TAPE DISPENSER
H-2590
1. When using automatic feed, remove the first piece
of tape. The unit will automatically feed and cut the
next piece at the preset length.
2. Feed length can be easily set using thumbwheel
controls.
3. Hold down shaft increases accuracy by maximizing
tape adhesion to the feed rollers.
4. The blade is easy to remove and replace.
5. Optional serrated blade for hard to cut materials.
6. Tape Length Display – Shows preset feed length.
Four-digit display can be set from 50-9999mm
(2" - 393").
7. Interval Knob – Sets delay time before dispensing
next piece.
8. Auto/Manual Switch – Toggles operating mode
between manual (press tape advance button
to dispense) and auto (automatic feed and cut
when piece is removed).
9. Power Switch – Press to turn power on and off.
10. Tape Advance Button – Press to feed and cut one
piece of tape to the preset length.
11. Hold Down Shaft – Increases adhesion to feed roller.
12. Reel Holder – 3" core to hold material.
13. Alarm – Lights when there is a malfunction in the unit.
FEATURES
REEL HOLDER
TAPE ADVANCE BUTTON
POWER SWITCH
ALARM
HOLD DOWN SHAFT
(UNDER TOP COVER)
MODE SELECTION
(MANUAL, AUTO & INTERVAL)
TAPE LENGTH DISPLAY
INTERVAL KNOB
0810 IH-2590PAGE 2 OF 3
1. After tape has been loaded and fed, turn power
switch off.
2. Set tape length display to required length using the
push buttons above and below the
numerical display.
NOTE: The length shown is in millimeters.
3. Flip auto/manual switch to desired location.
4. AUTO: When the cut piece of tape is removed from
the machine, the next piece is automatically fed
and cut. The interval knob will set the time delay
before the next piece is dispensed. Maximum delay
is 25 seconds.
5. MANUAL: The tape advance button must be pressed
each time a piece of tape is needed.
6. The tape will then be fed and cut.
7. Turn power switch on.
8. Press tape advance button to begin dispensing
tape.
NOTE: Tape lengths vary depending on
material. Verify length of first piece.
1. With power switch off, plug power cord into
dispenser and then into wall outlet.
2. Make sure machine is grounded properly.
3. Set the tape length display to 200mm.
4. Set the auto/manual switch to manual.
5. Turn dispenser power switch on, switch will be
illuminated.
6. Place tape roll on reel holder.
7. Put reel holder into reel holder slots.
8. Open latched top cover and remove metal hold
down shaft.
9. Press end of tape firmly onto metal feed roller, then
replace hold down shaft over tape and close top
cover.
10. Press tape advance button.
11. Remove tape then press tape advance button
again to ensure proper feeding.
SET-UP
OPERATION
SPECIFICATIONS
MODEL
#
TAPE
WIDTH
CUT
LENGTH
MAX.
OUTSIDE
DIAMETER
CORE
DIAMETER**
ACCURACY
OF CUT
*
TAPE
CUTTER
FEED
TYPE
LENGTH
SETTING WEIGHT DIMENSIONS
TDA080 .25 to 3.15"
(6.4 to 8.0mm)
2 to 394"
(50 to 9999mm)
9"
(251mm)
3"
(76.2mm)
+/- 0.4"
(1mm) Automatic Automatic Digital 21lbs.
(9.5kg)
9"(L) x 6.625"(W) x 12"(H) /
229mm(L) x 168mm(W) x 305(H)
• Auxiliary stand available for diameters up to 24”.
* Dependent on material.
** Other sizes available.
0810 IH-2590PAGE 3 OF 3
When problems occur, carry out the following procedures. If the tape dispenser does not operate normally after
following the troubleshooting procedures, contact your supplier.
WEEKLY
Wipe feed rollers and blade with proper solvent to
remove adhesive build-up.
MONTHLY
Apply silicone oil to #242 blade roller. Inspect pressure
rollers and cutting blade for wear.
TROUBLESHOOTING
MAINTENANCE
OPERATING ISSUE RECOMMENDATIONS
No power light / tape does not feed. Unplug unit and plug in again.
Turn power switch off, wait 5 seconds, turn unit back on.
Check that front panel is closed securely, and safety
interlock is engaged.
Verify that the fuse has not blown.
Check that Tape Length Display is 40mm or greater.
Tape does not feed when unit is in
auto mode.
Check that Auto/Manual Switch is in correct position.
Turn Interval Knob all the way counterclockwise.
Wait 1 full second after tape is cut before removing
tape from machine.
Blade sticks in closed position Apply silicon oil to #242 Blade Roller.
CHICAGO • ATLANTA • DALLAS • LOS ANGELES • MINNEAPOLIS • NYC/PHILA
Dieses Handbuch passt für folgende Modelle
1
Andere U-Line Spender Handbücher
U-Line
U-Line H-28 Bedienungsanleitung
U-Line
U-Line TORK MATIC H-9952 Bedienungsanleitung
U-Line
U-Line H-2243 Stücklistenhandbuch
U-Line
U-Line Econodot H-2930 Bedienungsanleitung
U-Line
U-Line KLEENEX REVEAL H-7855 Bedienungsanleitung
U-Line
U-Line H-878 Bedienungsanleitung
U-Line
U-Line H-2546 Bedienungsanleitung
U-Line
U-Line TORK H-7858 Bedienungsanleitung
U-Line
U-Line UHDE215 Installationshandbuch
U-Line
U-Line H-10657 Bedienungsanleitung
U-Line
U-Line I-I-1130 Bedienungsanleitung
U-Line
U-Line H-725 Bedienungsanleitung
U-Line
U-Line Boraxo H-3884 Bedienungsanleitung
U-Line
U-Line Purell Healthy Soap FMX-20 Bedienungsanleitung
U-Line
U-Line CDE224B Bedienungsanleitung
U-Line
U-Line TORK H-5808 Bedienungsanleitung
U-Line
U-Line H-1592 Bedienungsanleitung
U-Line
U-Line TORK XPRESS H-1596 Bedienungsanleitung
U-Line
U-Line TORK H-7859 Bedienungsanleitung
U-Line
U-Line H-4017 Bedienungsanleitung
