U-Line CS Series Bedienungsanleitung

PAGE 1 OF 3 0515 IH-2715

H-2715, H-2716

H -2717

OHAUS CS COMPACT

SCALE

OVERVIEW OF CONTROLS

CONTROL PANEL

CONTROL FUNCTIONS

BUTTON

PRIMARY FUNCTION

(Short Press) Changes unit of measure. Turns the scale on.

If the scale is on, sets zero.

SECONDARY FUNCTION

(Long Press) Enters calibration mode. Turns off the scale.

CONTROL PANEL PARTS

#DESCRIPTION

1 Unit Cal Button

2Zero Button

Unit

Cal

Zero

SERIES

PAGE 2 OF 3 0515 IH-2715

SET UP

WARNING! Verify that the AC Adapter input

voltage matches the local AC power supply.

Use the scale only in dry locations. For best

results, use the scale in the specified optimum

operating temperature. Do not operate the

scale in hostile or unstable environments. Use

the scale with care, gently loading items to be

weighed onto the center of the pan. Avoiding

rough treatment will aid in the life of your scale.

INSTALLING THE PLATFORM

1. Place the stainless steel pan onto the weighing

platform. (See Figure 1)

CONNECTING POWER

BATTERY

1. Remove the battery cover on the bottom of the scale.

2. Place 3 "AA" size batteries into the compartment.

CAUTION! Do not use excessive force or press

on the weighing pan.

3. Re-insert the battery cover.

AC POWER

1. Connect the AC adapter to the receptacle at the

rear of the scale.

2. Plug the AC adapter into a properly grounded

electrical outlet.

Figure 1

OPERATION

POWER UP TEST

When the scale is turned on, all display segments will

be displayed for a few seconds, indicating that the unit

is self adjusting to zero. Once the "0" is displayed, the

scale is ready for use.

STABLE READING INDICATION

A star indicator will appear in the lower left corner of the

display when a stable reading has been reached.

OVERLOAD

If the applied load exceeds the capacity of the scale,

an "E" will appear on the display and the load should

be removed immediately. The scale will return to normal

operation.

TARE FUNCTION

Values can progressively be added to a sample. By

pressing the

ON/OFF ZERO

button, the scale display

returns to zero. After adding additional mass, press

ON/OFF ZERO

to zero the scale again. Additional mass

may be added up to the capacity of the scale.

NEGATIVE VALUE

When a load is removed from the scale, any zeroed

value will be displayed as a negative number. To

return to normal operation, the zeroed value can be

cancelled by pressing

ON/OFF ZERO

button.

PAGE 3 OF 3 0515 IH-2715

LOW BATTERY INDICATION

The display will show "Lo" when the batteries are weak

and need to be replaced.

AUTO SHUT-OFF

To extend battery life, the scale will automatically turn off

after approximately (4) minutes if no active weighing is

occurring. This feature is active with battery operation only.

CALIBRATION

For best results calibrate the scale at regular intervals,

especially if using for prolonged periods. Calibration

weights are not provided with the scale.

The message CAL E will

appear if the calibration

steps are not followed or

the wrong weight was used.

1. Press and hold the

UNIT

CAL

button to start the

calibration process. The

display will show CAL.

NOTE: The calibration process can be aborted

by turning the scale off.

2. Press the

ON/OFF ZERO

button to capture 0. The

display shows -C- while

the scale stores the zero

load signal.

3. The display will show

Cxxx where xxx is the

calibration weight in

grams.

4. Place the appropriate calibration weight on the

platform.

5. Press the

ON/OFF ZERO

button. The display shows

-C- while the scale stores

the calibration point

signal.

6. After calibration, the

display returns to the

normal weighing mode.

OPERATION CONTINUED

CALIBRATION VALUES

MODEL # CALIBRATION POINT (g.)

H-2715 200

H-2716 1,000

H-2717 2,000

πCHICAGO • ATLANTA • DALLAS • LOS ANGELES • MINNEAPOLIS • NYC/PHILA • SEATTLE • MEXICO • CANADA

1-800 -295 -5510

uline.com

Dieses Handbuch passt für folgende Modelle

Andere U-Line Skala Handbücher

U-Line

U-Line H-1114 Bedienungsanleitung

U-Line

U-Line H-1121 Bedienungsanleitung

U-Line

U-Line H-9554 Installations- und Betriebsanleitung

U-Line

U-Line H-479 Bedienungsanleitung

U-Line

U-Line SCOUT H-9560 Bedienungsanleitung

U-Line

U-Line OHAUS VALOR 3000 Bedienungsanleitung

U-Line

U-Line H-9672 Bedienungsanleitung

U-Line

U-Line H-9884 Bedienungsanleitung

U-Line

U-Line H-1679-MNBRD Bedienungsanleitung

U-Line

U-Line H-103 Bedienungsanleitung

U-Line

U-Line H-1653 Bedienungsanleitung

U-Line

U-Line OHAUS DEFENDER 5000 Bedienungsanleitung

U-Line

U-Line H-2382 Bedienungsanleitung

U-Line

U-Line ADVENTURER PRO Series Bedienungsanleitung

U-Line

U-Line OHAUS SCOUT H-9596 Bedienungsanleitung

U-Line

U-Line H-7935 Bedienungsanleitung

U-Line

U-Line H-1607 Bedienungsanleitung

U-Line

U-Line OHAUS ADVENTURER H-5276 Bedienungsanleitung

U-Line

U-Line H-1101 Bedienungsanleitung

U-Line

U-Line OHAUS DEFENDER 3000 Bedienungsanleitung

U-Line

U-Line H-2382 Bedienungsanleitung

U-Line

U-Line H-3478 Bedienungsanleitung

U-Line

U-Line H-10903 Bedienungsanleitung

U-Line

U-Line H-8109 Bedienungsanleitung

Beliebte Skala Handbücher anderer Marken

AWS

AWS ZEO-50 Bedienungsanleitung

Gima

Gima Glass Body Fat Analyzer Stücklistenhandbuch

Seca

Seca 374 Bedienungsanleitung

TEC

TEC TEC SL59 SERIES Bedienungsanleitung

Axis

Axis B/E Series Bedienungsanleitung

Alecto

Alecto ACW-40 Bedienungsanleitung

Rice Lake

Rice Lake MSI-4260 IS Bedienungsanleitung

IKA

IKA RCT basic safety control Bedienungsanleitung

ADE

ADE M20011 Bedienungsanleitung

Duronic

Duronic KS3000 Bedienungsanleitung

Digi

Digi SM-720 Bedienungsanleitung

Cardinal

Cardinal CS Series Bedienungsanleitung

Korona

Korona Kastella Bedienungsanleitung

A&D

A&D FC-50Ki Bedienungsanleitung

BDA

BDA CAMARGUE Bedienungsanleitung

Tanita

Tanita HD-357 Bedienungsanleitung

Leifheit

Leifheit 03173 Bedienungsanleitung

Lumme

Lumme LU-1340 Bedienungsanleitung