U-Line SCOUT PRO H-2709 Bedienungsanleitung

0415 IH-2709PAGE 1 OF 8

SCOUT PRO

BALANCE SCALE

π1-800-295-5510

uline.com

H-2709, H-2710, H-2711

H-2712, H-2713, H-2382

H-2383, H-2384, H-3054

OVERVIEW OF CONTROLS

CONTROL PANEL CONTROL PANEL PARTS

#DESCRIPTION

1 ON/ZERO Off Button

2 Print Unit Button

1 2

CONTROL FUNCTIONS

BUTTON

PRIMARY FUNCTION

ON/ZERO

Turns on balance.

If balance is on, zeros the display.

Sends print command to interface port.

If Display Hold or Totalize mode is active,

a short press will enter that mode.

SECONDARY FUNCTION

OFF

Turns off balance. OFF will be displayed after the

button is held for 3 seconds.

In Display Hold or Totalize mode, a long press exits

the more without turning the balance off.

UNIT

Press and hold scrolls through units.

Release on desired unit.

MENU FUNCTION

An extended long press (>5 seconds) during power

up will cause the balance to enter the Menu mode.

A short press in used to accept a setting on a display.

Will bypass setting shown on display.

RELEASING THE SHIPPING LOCK

On the top of the balance, turn the pointer 90 degrees

counterclockwise to unlock. (See Figure 1)

PLATFORM INSTALLATION

Balances with a rectangular platform are placed

into the subplatform as shown and rotated

counterclockwise until they lock. (See Figure 2)

SETUP

Unlocked

Position

Locked

Position

Pointer

Figure 1

Figure 2

0415 IH-2709PAGE 2 OF 8

PLATFORM INSTALLATION CONTINUED

Round platforms are placed straight down on

subplatform. (See Figure 3)

SECURITY BRACKET

A security bracket is provided at the rear of the balance

allowing the balance to be secured by an optional

cable and lock accessory. (See Figure 4)

SELECTING THE LOCATION

For best performance, the scale should be used in a

clean, stable environment. Do not use in environments

with excessive drafts, with rapid temperature changes,

near magnetic fields or near equipment that generates

magnetic fields or vibrations.

CONNECTING POWER

BATTERY INSTALLATION

Install 4 "AA" batteries in the battery compartment.

(See Figure 5)

AC ADAPTER INSTALLATION

Plug the AC adapter into the jack at the rear of balance.

(See Figure 5)

Figure 5

Battery

Compartment

Cover

AC Adapter

Input Jack

SYMBOLS

The clock symbols adjacent to the finger symbol

indicates the length of time to press a button.

1 second momentary press.

3 second extended press.

5 second extended press.

Panel control buttons used to

initiate actions.

Displays are shown as they

appear on the balance.

Indicates scrolling to a final display. The first and

last displays are shown.

Indicates advances to next display.

TURNING THE BALANCE ON

TURNING THE BALANCE OFF

SETUP CONTINUED

Figure 3

Figure 4

Security Bracket

OPERATION

• • •

Press the button on the scale.

• • •

0415 IH-2709PAGE 3 OF 8

MENU NAVIGATION

ACCEPTING / BYPASSING MENU ITEM

Start with menu item displayed.

ENTERING THE MENUS

There are four main menus in the balance: .C.A.L,

.S.E.T.U.P., .U.N.I.T.S, and .E.N.D.

NOTE: Start with the balance off and the Lock

Switch off.

ENTERING THE .S.E.T.U.P. MENU

The .S.E.T.U.P. menu contains Auto-Off, Linearity

Calibration, Mode (Display Hold, Totalize) and END.

Auto-Off can be turned on or off. Display Hold and

Totalize require entering the Mode submenu. Starting

from the .C.A.L. menu.

NOTE: Select ON or OFF for Auto-Off. To enter

Display Hold or Totalize, you must first enter the

Mode sub-menu.

TURNING DISPLAY HOLD OR TOTALIZE MODE ON

NOTE: Only one mode can be active at one time.

Start at the .S.E.T.U.P. menu.

EXITING THE .S.E.T.U.P. MENU

Select

ON/OFF

YES/NO

to desired menu items,

proceed to .E.N.D. menu.

OPERATION CONTINUED

11(First menu)

1(To exit and save)

1 1

(Release button)

(Weigh mode)

Press YES to desired

mode, then continue.

Press repeatedly.

(Short presses) 1

•••

YNN

= YES Accept = NO

(Short press advances

through menu)

0415 IH-2709PAGE 4 OF 8

ENTERING THE .U.N.I.T. MENU

The .U.N.I.T. menu contains units of measure, PC (parts

counting), % weighing and END. Units vary with the model

type. Determine which units are to be turned on or off.

Start in the .U.N.I.T. menu. Select either

OFF

for

each unit.

NOTE: Repeated presses of PRINT Unit button

will go through all units, you then may select

ON or OFF. Parts Counting is slightly different.

PARTS COUNTING

Two types of counting modes are available: standard or

enhanced.

EXITING THE .U.N.I.T. MENU

Use the same procedure as exiting the .S.E.T.U.P. Menu.

OPERATION CONTINUED

CALIBRATION

ULINE MODEL NO. H-2709 H-2710 H - 2111 H-2382 H-2383 H-2384 H-2712 H-3054 H-2713

OHAUS MODEL NO. SPx202 SPx402 SPx602 SPx401 SPx601 SPx2001 SPx4001 SPx6001 SPx6000

Span Calibration Mass (g)

0, 200 0, 200 0, 300 0, 200 0, 300 0, 2000 0, 4000 0, 6000 0, 4000

Linearity Calibration Mass (g)

0, 100,

200

0, 200,

400

0, 300,

600

0, 200,

400

0, 300,

600

0, 1000,

2000

0, 2000,

4000

0, 3000,

6000

0, 3000,

6000

CALIBRATION VALUES

(Turn on) (To accept)

(To advance)

SPAN CALIBRATION

Span calibration uses two calibration points, zero and a

specified calibration weight.

Before beginning calibration, make sure the Lock Switch

is unlocked. Clear the platform.

NOTE: Value of calibration mass depends on

capacity of balance. After calibration, the balance

returns to the currently selected weigh mode.

1. Start with the balance OFF.

2. Hold the

ON/ZERO Off

button until the display reads

MENU CAL

3. Press and release

ON/ZERO Off

. Scale will flash

- C- and show required weight. Place the calibration

weight on the scale.

4. Press and release

ON/ZERO Off

. Scale will show

donE; remove weight.

•••

(Acquiring zero value)

(Place mass value

on platform)

(Remove mass)

0415 IH-2709PAGE 5 OF 8

OPERATION CONTINUED

LINEARITY CALIBRATION

Linearity calibration uses three calibration points; zero,

mid-scale and full scale. Lin Cal must be selected

and set to YES in the .S.E.T.U.P. Menu. Before beginning

calibration, make sure the menu Lock Switch is

unlocked. Clear the platform. Start with the balance OFF.

WEIGHING

Start with the balance on.

WEIGHING WITH TARE

Taring zeros the container weight. With the balance on,

place an empty container on the platform.

NOTE: Removing the container and material

from the platform will cause the balance to

display the container’s weight as a negative

number. The tared weight remains until ON/

ZERO Off button is pressed again or the

balance is turned off.

PARTS COUNTING

Parts Counting is enabled only when PC is turned ON in

the .U.N.I.T. menu. In parts counting mode, there are two

modes of parts counting, standard and enhanced.

STANDARD PARTS COUNTING

In standard parts counting, the balance determines the

quantity based on the average weight of the parts in

the original reference quantity.

1 1

(Place mass value on platform)

(Remove mass)

(Stable reading)

(Rezero the display) (Place sample on platform)

(Container weight) (Container weight tared)

(Place material in container)

(Remove container with material)

(Place 50 parts) (Add parts to be counted)

(Press and hold until

PC is displayed)

(Press repeatedly to

change to 10, 20 or 50)

(Clear average part weight)

0415 IH-2709PAGE 6 OF 8

ENHANCED PARTS COUNTING

In the enhanced mode, additional parts can be added

to the platform equal to or less than the original number.

The additional reference quantity produces a more

accurate average part weight.

NOTE: Enhanced Parts Counting can be

repeated as many times as necessary

providing the quantity added is less than the

original entry.

To count different parts, press and hold, until PC

reappears, release

Unit

button.

PERCENT WEIGHING

Percent Weighing is enabled only when Percent is

turned ON in the .U.N.I.T. menu. Percent weighing

permits placing a reference weight on the balance,

then viewing other loads as a percentage of the

reference. The reference weight equals 100%.

Start in the weighing mode and zero the display.

Place load on the platform to display percent of

reference weight.

ESTABLISHING A NEW REFERENCE WEIGHT

Press and hold until % on the display reappears, then

release.

Repeat above procedure for new a reference weight.

EXITING PERCENT WEIGHING

Press and hold until desired unit is displayed.

DISPLAY-HOLD

Display-Hold is enabled only when Hold is turned ON in

the Mode submenu in the .S.E.T.U.P. menu. Display-Hold

mode captures and stores the highest stable value.

When displayed, the stable icon will blink.

NOTE: Units cannot be changed when in

display hold mode.

EXITING DISPLAY HOLD

To return to display-hold, repeat above procedure.

OPERATION CONTINUED

(Add less than 50)

(Add parts to be counted)

(Press and hold until % is displayed)

(Place reference

weight)

(Stores reference

weight)

(Remove reference weight)

(Place item(s) on platform)

0415 IH-2709PAGE 7 OF 8

TOTALIZE

Totalize is enabled only when Total is turned ON in the

Mode submenu in the .S.E.T.U.P. menu. Totalize allows

storage of a series of weight measurements. Totalize

mode has been initiated when "t" and the current unit,

i.e., (g) is displayed. When totalized weight is shown,

the "t" indicator will blink.

NOTE: Units cannot be changed when in

display hold mode.

Total weight will remain on the display until weight is

removed. The total weight remains in memory. Total is

limited to 999999.

CLEAR/EXIT TOTALIZE

Performing this step will erase all totalized memory.

ADDITIONAL FEATURES

WEIGH BELOW

Scout Pro permits below

balance weighing for

applications such as

specific gravity/density

determination. The

balance is normally

elevated, supported on

all feet and leveled. A

fine wire is attached to

the built-in hook at the

bottom of the balance

LOCK SWITCH

The Lock Switch is located under the balance. The Lock

Switch is used to lock out the menu mode preventing

unauthorized changes.

To lock the menus, position the Lock Switch next to the

tab on the bottom of the balance as shown.

(Place first weight

on platform)

(Place second

weight on platform)

(Remove weight)

(Total weight shown)

(Remove weight) (Place third weight on platform)

(Total weight shown) (Remove weight)

Weigh

Below

Hook

Locked positionUnlocked

OPERATION CONTINUED

MAINTENANCE

CLEANING

To ensure proper balance operation, keep the housing

platform clean. If necessary, a cloth dampened with a

mild detergent may be used. Check under the platform

for debris and remove.

NOTE: Keep calibration masses in a safe, dry

place. Unplug the AC Adapter when not in use.

For long term storage, remove the batteries.

0415 IH-2709PAGE 8 OF 8

OPERATING ISSUE CAUSES RECOMMENDATIONS

No display. Power Adapter not connected.

Batteries are exhausted.

Connect AC adapter.

Replace batteries.

Battery Indicator is flashing. Batteries are weak. Replace batteries.

Incorrect weight reading. Balance out of calibration.

Balance was not rezeroed before

weighing.

Calibrate the balance.

Press the

ON/ZERO Off

button with no weight

on the platform, then weigh item.

Calibration procedures do

not work.

Incorrect calibration masses being used. Use correct masses.

See error codes note ERR4.

Unable to switch unit of

measure.

Weighing unit not activated in menu.

Mode prevents unit change.

Use Units menu to set desired units ON.

Exit Hold or Totalize mode.

Balance readings unstable. Balance location may have drafts from

air conditioning vents or vibration from

other appliances nearby affecting

operation.

Either move or shield the balance from

external air currents or vibration.

Err 1 chEct Invalid checksum data. Cycle balance ON/OFF.

Return balance for service.

Err 2 LoAd Overload (>cap+90d) or Underload. Remove load.

Make sure shipping lock is unlocked.

Recalibrate.

Err 4 WEIght Incorrect calibration weight. Use correct calibration weights.

Check environmental conditions.

Err 5 999999 Displayed value>99999. Exit application.

Rezero balance.

Err 6 count Parts counting error – balance exits

parts counting.

Exit application.

Rezero balance.

Err 8 FULL RS232 buffer is full. Cycle ON/OFF.

Check RS-232 settings in balance and

computer.

Err 9 dAtA Internal data error. The next button

press or a 5 second time-out causes

the balance to turn off.

Cycle ON/OFF.

Return balance for service.

TROUBLESHOOTING

πCHICAGO • ATLANTA • DALLAS • LOS ANGELES • MINNEAPOLIS • NYC/PHILA • SEATTLE • MEXICO • CANADA

1-800-295-5510

uline.com

If the troubleshooting section does not resolve your problem, contact ULINE Customer Service at 1-800-295-5510.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere U-Line Skala Handbücher

U-Line

U-Line H-9884 Bedienungsanleitung

U-Line

U-Line H-3677 Bedienungsanleitung

U-Line

U-Line H-1101 Bedienungsanleitung

U-Line

U-Line OHAUS SCOUT H-9596 Bedienungsanleitung

U-Line

U-Line CS Series Bedienungsanleitung

U-Line

U-Line H-2714 Bedienungsanleitung

U-Line

U-Line H-1096 Bedienungsanleitung

U-Line

U-Line H-479 Bedienungsanleitung

U-Line

U-Line H-1679 Bedienungsanleitung

U-Line

U-Line H-9554 Installations- und Betriebsanleitung

U-Line

U-Line H-9672 Bedienungsanleitung

U-Line

U-Line OHAUS DEFENDER 5000 Bedienungsanleitung

U-Line

U-Line H-4602 Bedienungsanleitung

U-Line

U-Line OHAUS DEFENDER 3000 Bedienungsanleitung

U-Line

U-Line SCOUT H-9560 Bedienungsanleitung

U-Line

U-Line H-5836 Bedienungsanleitung

U-Line

U-Line H-754 Handbuch

U-Line

U-Line H-9983 Bedienungsanleitung

U-Line

U-Line H-670 Bedienungsanleitung

U-Line

U-Line H-1679-MNBRD Bedienungsanleitung

U-Line

U-Line ADVENTURER PRO Series Bedienungsanleitung

U-Line

U-Line H-2289 Bedienungsanleitung

U-Line

U-Line OHAUS DEFENDER 3000 Bedienungsanleitung

U-Line

U-Line H-1096 Bedienungsanleitung

Beliebte Skala Handbücher anderer Marken

AWS

AWS ZEO-50 Bedienungsanleitung

Gima

Gima Glass Body Fat Analyzer Stücklistenhandbuch

Seca

Seca 374 Bedienungsanleitung

TEC

TEC TEC SL59 SERIES Bedienungsanleitung

Axis

Axis B/E Series Bedienungsanleitung

Alecto

Alecto ACW-40 Bedienungsanleitung

Rice Lake

Rice Lake MSI-4260 IS Bedienungsanleitung

IKA

IKA RCT basic safety control Bedienungsanleitung

ADE

ADE M20011 Bedienungsanleitung

Duronic

Duronic KS3000 Bedienungsanleitung

Digi

Digi SM-720 Bedienungsanleitung

Cardinal

Cardinal CS Series Bedienungsanleitung

Korona

Korona Kastella Bedienungsanleitung

A&D

A&D FC-50Ki Bedienungsanleitung

BDA

BDA CAMARGUE Bedienungsanleitung

Tanita

Tanita HD-357 Bedienungsanleitung

Leifheit

Leifheit 03173 Bedienungsanleitung

Lumme

Lumme LU-1340 Bedienungsanleitung