U.S. Products SPOTTER Bedienungsanleitung

1/10 revised 11/13 FROM NO. 56041856



56041856

IMPROPER USE OF THE MACHINE WILL VOID THE WARRANTY

CAUTION: DO NOT OPERATE MACHINE UNTIL YOU HAVE READ

ALL SECTIONS OF THIS INSTRUCTION MANUAL

1. Keep all ﬁlters clean. Do not operate the machine if the ﬁlters are clogged.

2. All extension cords must be 18/3 and no longer than 50 ft.

3. Do not let the pump run dry. Always turn the switch OFF when you are not actively cleaning

4. Always use defoamer in the recovery tank to prevent damage to the vacuum motor.

5. Use the Spotter indoors only, and only for it’s designed purpose.

6. Always empty the recovery tank when reﬁlling the water in the tank(s).

7. Use approved chemicals only. NEVER use solvents.

SPOTTER

MODELS: SPOTTER, SPOTTER-240, SPOTTER-DZ

SPOTTER-B, SPOTTER-S

INFORMATION AND

OPERATING

INSTRUCTIONS

https://harrissupplyind.com-ToOrderPartsCall608-268-8080

INTRODUCTION

This manual will help you get the most from your equipment. Read it thoroughly before operating the machine.

This product is intended for commercial use only.

PARTS AND SERVICE

Repairs, when required, should be performed by your Authorized Service Center, who employs factory trained service personnel, and maintains an

inventory of original replacement parts and accessories.

Call for repair parts or service. Please specify the Model and Serial Number when discussing your machine.

MODIFICATIONS

Modiﬁcations and additions to the cleaning machine which affect capacity and safe operation shall not be performed by the customer or user

without prior written approval from the manufacturer. Unapproved modiﬁcations will void the machine warranty and make the customer liable for

any resulting accidents.

NAMEPLATE

The Model and Serial Number of your machine are shown on the Nameplate. This information is needed when ordering repair parts for the

machine. Use the space below to note the Model and Serial Number of your machine for future reference.

Model _________________________________________

Serial Number ___________________________________

UNPACKING THE MACHINE

When the machine is delivered, carefully inspect the shipping carton and the machine for damage. If damage is evident, save the shipping carton

so that it can be inspected.

CLEANING SOLUTIONS:

Use only approved chemicals. Liquid cleaning detergents are recommended; powdered chemicals may be used, but unless mixed thoroughly,

they may cause a build-up in the pump, the lines, the quick couplers, etc. High acid concentration, as in citrus based cleaners, or strong detergent

preparations, can damage the pump seals and/or other ﬁttings, and are expressly warned against. A pH of between 5 and 10 is recommended.

Damage caused by either strong acid or strong detergent will void the warranty.

WARNING!

The Products sold with this Manual contain or may contain chemicals that are known to certain governments (such as the State of California, as

identiﬁed in its Proposition 65 Regulatory Warning Law) to cause cancer, birth defects or other reproductive harm. In certain locations (including

the State of California) purchasers of these Products that place them in service at an employment job site or a publicly accessible space are

required by regulation to make certain notices, warnings or disclosures regarding the chemicals that are or may be contained in the Products at

or about such work sites. It is the purchaser’s responsibility to know the content of, and to comply with, any laws and regulations relating to the

use of these Products in such environments. The Manufacturer disclaims any responsibility to advise purchasers of any speciﬁc requirements that

may be applicable to the use of the Products in such environments.

revised 2/12

A - 2 SPOTTER - 56041856 1/10

INSTRUCTIONS FOR USEA - ENGLISH

https://harrissupplyind.com-ToOrderPartsCall608-268-8080

IMPORTANT SAFETY INSTRUCTIONS

This machine is only suitable for commercial use, for example in hotels, schools, hospitals, factories, shops and ofﬁces other than

normal residential housekeeping purposes.

When using any electrical appliance, basic precautions should always be followed, including the following:

NOTE: Read all instructions before using this machine.

WARNING!

To reduce the risk of ﬁre, electric shock, or injury:

• Do not leave the machine unattended when it is plugged in. Unplug the unit from the outlet when not in use and before

servicing.

• To avoid electric shock, do not expose to rain or snow. Store, and use, indoors.

• Do not allow to be used as a toy. Close attention is necessary when used near children.

• Use only as described in this manual. Use only the manufacturer’s recommended

attachments.

• Never add water over 130º F/54º C to the solution tank.

• Do not use with damaged cord or plug. If the machine is not working as it should, has been dropped, damaged, left outdoors or

dropped into water, return it to a service center.

• Do not pull by the cord, use the cord as a handle, close a door on the cord, or pull the cord around sharp edges or corners. Do

not run the machine over the cord. Keep the cord away from heated surfaces. To unplug, grasp the plug, not the cord.

• Do not handle the plug, the cord, or the machine with wet hands.

• Extension cords must be 18/3 and no longer than 50 feet (15M). Replace the cord or unplug immediately if the ground prong

becomes damaged.

• Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything that may

reduce air ﬂow.

• Keep loose clothing, hair, ﬁngers, and all parts of body away from openings and moving parts.

• Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes, or any health endangering dusts.

Do not use to pick up ﬂammable or combustible liquids such as gasoline or use in areas where they may be present.

• Turn off all controls before unplugging.

• Use extra care when cleaning on stairs.

• Connect to a properly grounded outlet only.

• Liquid ejected at the spray nozzle could be dangerous as a result of its temperature, pressure, or chemical content.

SAVE THESE INSTRUCTIONS

revised 2/12

1/10 A - 356041856 - SPOTTER

ENGLISH - AINSTRUCTIONS FOR USE

https://harrissupplyind.com-ToOrderPartsCall608-268-8080

120VAC GROUNDING INSTRUCTIONS

This appliance must be grounded. If it should electrically malfunction, grounding provides a path of least resistance for electric current to reduce

the risk of electric shock. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be

plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

DANGER!

Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualiﬁed electrician or

service person if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the appliance.

If it will not ﬁt the outlet, have a proper outlet installed by a qualiﬁed electrician.

This appliance is for use on a nominal 120-volt circuit, and has a grounding plug that looks like the plug illustrated in Figure 1 below. A temporary

adapter illustrated in Figures 2 and 3 may be used to connect this plug to a 2-pole receptacle as shown in Figure 2 if a properly grounded outlet is

not available. The temporary adapter should be used only until a properly grounded outlet (Figure 1) can be installed by a qualiﬁed electrician. The

green-colored rigid ear, tab, or the like extending from the adapter must be connected to a permanent ground such as a properly grounded outlet

box cover. Whenever the adapter is used, it must be held in place by a metal screw. Grounding adapters are not approved for use in Canada.

Replace the plug if the grounding pin is damaged or broken.

The Green (or Green/Yellow) wire in the cord is the grounding wire. When replacing a plug, this wire must be attached to the grounding pin only.

Extension cords connected to this machine should be 12 gauge, three-wire cords with three-prong plugs and outlets. DO NOT use extension

cords more than 50 feet (15 m) long.

PLEASE NOTE: FOR NORTH AMERICA ONLY

revised 2/12

Grounding Pin

Tab for Grounding Screw

Adapter

Metal Screw

FIGURE 1 FIGURE 2 FIGURE 3

Grounded Outlet Box

Grounded Outlet

FEATURES:

Solution Tanks:

The Triple-Play Spotter has the unique design feature of having two, 1-gallon (3.75L) Solution Tanks (1 & 2). This allows you to have cleaning solution in one tank

and clean water for rinsing in the other tank. Simply turn the Solution Valve (3) on the rear of the machine to switch from one tank to the other. There is no need to

empty your detergent tank, clean it, and reﬁll it with water for the rinse cycle.

VacuumTank:

The Vacuum Tank (4) holds more liquid than the total of both the Solution Tanks (1 & 2), so you can easily clean an area and rinse it without the need to empty

your vacuum tank. When you reﬁll your solution tanks, simply remove the vacuum hose from the recovery tank and dump the water out through the Vacuum Inlet

(5).

CAUTION!

• To prevent damage to the vacuum motor, do not let the water level in the Vacuum Tank (4) exceed 3/4 full.

• When moving the machine with water in any of the tanks, do not tip the machine past a 30° angle to avoid spilling water into the vacuum

chamber which will damage the vacuum motor.

A - 4 SPOTTER - 56041856 1/10

INSTRUCTIONS FOR USEA - ENGLISH

https://harrissupplyind.com-ToOrderPartsCall608-268-8080

SET-UP:

1. Open the Latches (6) and remove the Vacuum Tank (4) from the machine.

2. Fill the Solution Tanks (1 & 2) -- one tank will hold your diluted cleaning chemical and the second tank will hold clean water.

3. Place the Vacuum Tank (4) back onto the base, and secure the Latches (6). Make sure the Screw-in Access Lid (7) is in place and tight.

4. Attach the Vacuum Hose (8) to the Vacuum Inlet (5) on the Vacuum Tank (4).

5. Connect the Solution Line (9) to the Quick Coupling (10) on the front of the spotter base.

6. Attach the Cleaning Tool (11) to the other end of the Vacuum Hose (8) and Solution Line (9)..

7. Turn the knob on the Solution Valve (3) to the desired tank.

8. Turn the Rocker Switch (12) on. This will start the pump and the vacuum.

9. Press the lever on the tool to begin spraying.

NOTE: It may take a few seconds for the solution to reach the spray tip. The tool will automatically suck up the sprayed solution as the tool passes over the

wet area.

NOTE: When switching from one tank to the other tank, it may take a few seconds of spraying for the solution in the selected tank to reach the spray tip.

10. When ﬁnished with the job, disconnect the hoses from the Spotter, remove and empty the Recovery Tank (4), then dump the water out of the Solution Tanks

(1 & 2) and clean them.

revised 2/12

1/10 A - 556041856 - SPOTTER

ENGLISH - AINSTRUCTIONS FOR USE

https://harrissupplyind.com-ToOrderPartsCall608-268-8080

TROUBLESHOOTING

CAUTION!

ALWAYS UNPLUG THE MACHINE BEFORE YOU DO ANY INTERNAL TROUBLESHOOTING

IF THIS OCCURS CHECK THIS

Pump Not Working Check Electrical Connections

Vac Motor Not Working Check Electrical Connections

SPECIFICATIONS AND FEATURES:

Solution Tank: 1 gallon - 3.785 liters

Rinse Tank: 1 gallon - 3.785 liters

Recovery Tank: 2.5 gallons - 9.5 liters

Pump: 55 PSI

Tangential Vacuum: 90-inch lift/97 CFM

Power Cable: 25-foot (8M) length 18/3 w/hospital grade plug

Hand Tool: 3.5-inch (9cm) stainless steel/clear resin

Transport: 5-inch (13cm) wheels w/folding handle

Weight: 29 lbs. (13kg)

Dimensions: 25” L x 10.5” W x 19” H (63cm x 26.5cm x 48cm)

Warranty: 2-year limited

Optional Equipment: Lightweight ﬂoor wand

revised 2/12

A - 6 SPOTTER - 56041856 1/10

INSTRUCTIONS FOR USEA - ENGLISH

https://harrissupplyind.com-ToOrderPartsCall608-268-8080

revised 11/13

TRIPLE PLAY SPOTTER

22 23

38 39

28 29

D - 2 SPOTTER - 56041856 1/10

PARTS LIST

https://harrissupplyind.com-ToOrderPartsCall608-268-8080

TRIPLE PLAY SPOTTER

Item Ref. No. Qty Description

1 17 10 Nut-Nylon Lock-Ss-10-32

2 18 1 Nut-Hex Nyl Loc Ss 4-40

3 21 4 Screw 10-32 X 5/8 Socket

4 22 7 Fhp-10-32 5-8

5 24 3 Washer-Flat-Ss-10

6 28 3 Screw-Php-Ss-4x3/8-Sms

7 30 1 Screw 10-24 X 1/2 Hex Hea

8 35 1 Tie 4 Black Weather Resis

9 90 1 Elbow 90 Brass1/8 Fm .X 1/

10 97 2 Bushing Pipe 1/4 Male Pipe X

11 265 2 Washer Buna 11/32 X .0625 Thick

12 267 6 Screw-Php-Ss-6x1/2-Sms

13 357 2 Washer 7/16 An Flat Ss

14 374 1 Quick Disconnect Plug 1/8 K

15 384 1 Hose Barb Brass 1/8 Mpt X 1/

16 385 8 Hose Clamp 1/4 X 5/8 X 7/16 Wi

17 386 3 Scr-Flt Phil Ss 10-32 X 4.00

18 390 3 Nut-Hex Machine 10-32

19 408 1 Vac Motor, 120v

407A 1 Vacuum Motor 5.7 240 V 2- (SPOTTER-240)

20 416 0.75” Tubing Teﬂon 3/16 Id X .03

21 440 1 Flange Exhaust Black Polypr

22 981 1 Gasket Tank 11-1/2 X 8-3/1

23 984 1 Power Cord 18/3 Sjtw 25 B

2019 300” Powercord European Color Code (SPOTTER-240)

24 986 1 Plate Bottom Cover Spotter

25 990 2 Bracket L For Spotter Pump

26 994 1 Plate-Mounting-Vacuum-Spotter

27 996 25.5” Hose Braided 1/4 Id Clear

28 996 16” Hose Braided 1/4 Id Clear

29 996 10.5” Hose Braided 1/4 Id Clear

30 996 22.5” Hose Braided 1/4 Id Clear

31 999 2 Filter 40 Mesh S/S 1/4 Npt

32 1000 4 Hose Barb 90 Deg Nylon 1/8 Mpt

33 1117 4 Scr-Pan Phil 8-32 X .25

34 2013 1 Gasket 1 Side Adhesive 5-1/2 O

35 56471194 2 Latch Assembly

36 56750746 1 Nipple, 1/8npt X .75

37 56755726 2 Barb, Hose Male

38 230A 1 Nut-Lock-Nylon

39 230USP 1 Retainer Power Cord Water T

40 27AUSP 2 Axel Cap Black Pal Nut

41#306AB 3 Washer-Flat-Hh-Brass-7/8odx.412idx1/16 Thick

42 315A 1 Screw-Php-Ss-Zp-4-40x3/4-Ms

43 39857A 2 Wheel 5 X 1.50 X .500

44 988B 1 Valve 3-Way For Spotter & Apc

45 989USP 1 Pump 55 Psi 120v For Spotter

989A 1 Pump 55 Psi W/ Viton Seal For (SPOTTER-240)

46 FP454 1 Holding Tank Spotter-Black (SPOTTER, SPOTTER-240, SPOTTER-B)

56381319 1 Holding Tank-Spotter Mold KB (SPOTTER-DZ)

56381360 1 Holding Tank-Spotter Mold TEAL (SPOTTER-S)

47 987 1 Switchplate Spotter

48 2123 1 Switch Rocker Dpst W/Light 120

48G 1 Switch Rocker Spst W/Light 230 (SPOTTER-240)

49 325 6 Nut-Nylon Lock-Ss-8-32

50 808 1 Screw 6x3/8 S/S Trusshead P

51 980 1 Gasket Vacuum Seal 2.9 X 6

52 983 1 LID And RING 4 LID CLEAR

53 1074B 1 Gasket-Lid-Xlpe-4.5idx3/16 Thick

54 21C 5 Screw-Php-Ss-8-32x5/8

55 325C 4 Bolt-Php-Ss-8-32x1/2

56 382C 1 Screw 8-32 X 7/8 Panhead Phi

57 805USP 1 Chain-Cover

58 909A 2 Latch-Strike-Ss-No 8 Hole

59 56381341 1 Vac Tank-Spotter Mold Wht

56381684 1 Vac Tank-Spotter Mold Red (SPOTTER-B)

#= Revised or new since last update

revised 11/13

1/10 D - 356041856 - SPOTTER

PARTS LIST

https://harrissupplyind.com-ToOrderPartsCall608-268-8080

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere U.S. Products Bodenreinigungsmaschine Handbücher

U.S. Products

U.S. Products KING COBRA 310 Betriebsanleitung

U.S. Products

U.S. Products HYDRAPORT 100SC Betriebsanleitung

U.S. Products

U.S. Products Kraken Neptune 500 Betriebsanleitung

U.S. Products

U.S. Products COBRA-300H Betriebsanleitung

U.S. Products

U.S. Products KING COBRA 150 Betriebsanleitung

U.S. Products

U.S. Products King Cobra KC-500 Betriebsanleitung

U.S. Products

U.S. Products COBRA-300H Bedienungsanleitung

U.S. Products

U.S. Products PEX 500 Betriebsanleitung

U.S. Products

U.S. Products HYDRAPORT 1200 Bedienungsanleitung

U.S. Products

U.S. Products Agitator 20 Betriebsanleitung

U.S. Products

U.S. Products KING COBRA 300 Betriebsanleitung

U.S. Products

U.S. Products AGITATOR 16 Bedienungsanleitung

U.S. Products

U.S. Products KING COBRA 1200 PRO Bedienungsanleitung

U.S. Products

U.S. Products 100-041-016 Bedienungsanleitung

U.S. Products

U.S. Products PB111-120 Bedienungsanleitung

U.S. Products

U.S. Products KING COBRA 310-CSA Bedienungsanleitung

U.S. Products

U.S. Products ADVANTAGE-400H Series Betriebsanleitung

U.S. Products

U.S. Products KING COBRA 1200 PRO Betriebsanleitung

U.S. Products

U.S. Products ADVANTAGE-400H Series Betriebsanleitung

U.S. Products

U.S. Products COBRA-H Bedienungsanleitung

Beliebte Bodenreinigungsmaschine Handbücher anderer Marken

Nilfisk-Advance

Nilfisk-Advance Advance SC370 17B Bedienungsanleitung

Numatic

Numatic ET 4045 Bedienungsanleitung

HAWK ENTERPRISES

HAWK ENTERPRISES HP1513-180BRUTE Bedienungsanleitung

Mytee

Mytee 8070 Mytee-Lite Bedienungsanleitung

Kärcher

Kärcher B 140 R Bedienungsanleitung

Triple S

Triple S Ace 26T1 Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance SW 750 Bedienungsanleitung

Tornado

Tornado Marathon 2000 98190 Handbuch

Windsor

Windsor ADMIRAL Admiral 8 Bedienungsanleitung

Numatic

Numatic TTB 1117/100 Bedienungsanleitung

Tennant

Tennant 8210D Bedienungsanleitung

Nobles

Nobles Frontier Produkthandbuch

lavina

lavina 21-X Bedienungsanleitung

KENT

KENT Edge 28B Bedienungsanleitung

Tennant

Tennant 215 Produkthandbuch

Windsor

Windsor BDP 51/2000C Bedienungsanleitung

CleanFreak

CleanFreak DURA-18HD Bedienungsanleitung

Nilfisk-Advance

Nilfisk-Advance Warrior 34RST Administratorhandbuch