Ubiquiti U-Installer Bedienungsanleitung
Installer
Quick Start Guide
Hardware Overview
USB-C Port
Wi-Fi LED
PoE OUT
Port
Removable
Rubber
Casing
Battery
LEDs
Front View
Ports
PoE OUT Supplies 24V passive PoE to
the device being installed.
USB-C USB Type C port used for
charging the internal battery.
LEDs
Wi-Fi
Lights blue if the U‑Installer has
a Wi‑Fi connection to your mobile device.
Battery
Four blue LEDs indicate the
internal battery’s charge level:
Full charge
Low charge*
* Recharge the battery by connecting a power source,
such as a mobile battery pack, to the USB-C port.
Back View
Buttons
Removable
Rubber
Casing
Clip
Buttons
Reset Ext
Power
Reset
Reset Ext
To reset the device connected
to the U‑Installer to factory defaults,
press this button while the device is
powered on. Hold the button for more
than eight seconds until the LEDs on the
device flash.
Power Press to power the U‑Installer
on or off. The Battery LEDs light when
power is on.
Reset To reset the U‑Installer to factory
defaults, press and hold the Reset
button while the U‑Installer is powered
on
until the LEDs on the device flash.
Configure a CPE Device
Use a mobile device (default method)
or a laptop to configure the CPE device
at the point of installation via the
U‑Installer’s Wi‑Fi:
1. Power on the U‑Installer by pressing
the Power button. The Battery LEDs
light when the power is on.
Note: If the battery level is
low, connect a USB cable from
a mobile power pack or USB
charger to the USB-C port of the
U‑Installer.
2. Connect an Ethernet cable to the
PoEOUT port on the U‑Installer.
3. Connect the other end of the cable to
the CPE device.
You have two options for configuration:
the UMobile App and Web Portal.
Proceed to the appropriate instructions:
UMobile App - Default Method
1. iOS devices only: Connect your
mobile device’s Wi‑Fi to the U‑Installer
SSID named: ubi:<MAC Address>
2. Launch the UMobile app on your
mobile device.
Note: If the UMobile app is not
yet installed on your mobile
device, download it from
AppStore (iOS) or Google Play™
(Android).
3. The Connections screen appears.
4. Connect to the CPE device as follows:
iOS:
a. On the Connections screen, tap the
CPE device.
b. Tap Log in to automatically log
into the device.
Android:
a. Tap , and then tap Installer.
b. The app will automatically detect
and connect to the U‑Installer SSID
named: ubi:<MAC Address>.
c. On the Discover screen, tap the CPE
device to automatically log into
the device.
5. Follow the on‑screen instructions in
the UMobile app to configure the
connected device.
Web Portal
1. Connect your device’s Wi‑Fi to the
U‑Installer SSID named:
ubi:<MAC Address>
2. Open a web browser and go to:
https://192.168.1.20
3. The login portal of the CPE device will
appear. Log in using the appropriate
username and password.
Example Login Screen for CPE Device
4. Configure theCPE device as needed.
Removing the U‑Installer
After you have configured the CPE
device, remove the U‑Installer:
1. Disconnect the Ethernet cable from
the device.
2. Connect the Ethernet cable from a PoE
adapter or switch to the device.
Andere Handbücher für U-Installer
2
Inhaltsverzeichnis
Andere Ubiquiti Adapter Handbücher
Ubiquiti
Ubiquiti mPort Bedienungsanleitung
Ubiquiti
Ubiquiti AIR FIBER 11FX Bedienungsanleitung
Ubiquiti
Ubiquiti UniFi Protect ViewPort Bedienungsanleitung
Ubiquiti
Ubiquiti mPower mini Bedienerhandbuch
Ubiquiti
Ubiquiti mPower Bedienungsanleitung
Ubiquiti
Ubiquiti mPower mini Bedienungs- und Wartungsanleitung
