Ubiquiti TS-16-CARRIER Bedienungsanleitung

Rack-Mount

Power over Ethernet

Managed Switches

Model: TS-16-CARRIER

Introduction

Thank you for purchasing the Ubiquiti Networks®

TOUGHSwitch™CARRIER. This Quick Start Guide is designed to

guide you through installation and includes warranty terms.

Package Contents

TOUGHSwitch CARRIER

Flathead Screws

(M3x8, Qty. 2)

Phillips Screws

(#10-32 x 5/8”, Qty. 4)

Cage Nuts

(#10-32 x 5/8”, Qty. 4)

Rack-Mount

Power over Ethernet

Managed Switches

Model: TS-16-CARRIER

Power Cords (Qty. 2) Quick Start Guide

and earth grounding must be used for outdoor installations as conditions of product warranty.

TOUGHCable™ is designed for outdoor installations. It is the customer’s responsibility to follow

local country regulations, including operation within legal frequency channels, output power,

and Dynamic Frequency Selection (DFS) requirements.

Hardware Overview

Aand Bdesignate the two 8-Port TOUGHSwitch PoE PROs

housed in the rack. This may be useful for the Location setting

on the Device tab in the Configuration Interface.

Front Panel Ports

Management Ports 1-8

ResetUSB

Management Ports 1-8

ResetUSB

TOUGHSwitch A TOUGHSwitch B

Interface Description

Management 10/100 Mbps port used to access the

TOUGHSwitch Configuration Interface.

Ports 1-8 10/100/1000 Mbps ports for switching and

PoE (also available for management by

default).

USB Reserved for future use.

Reset

To reset to factory defaults, press and hold

the Reset button for more than 10 seconds

while the unit is already powered on.

Back Panel

Power Power

Ventilation HolesVentilation Holes

Note: There are additional ventilation holes on the top

and sides of the TOUGHSwitch.

Front Panel LEDs

Power/Link

PoE

Speed/Link/Act

LED State Status

MGMT

Power/

Link

Off No Power/No Link

Amber

After bootup, the LED indicates

power. After an initial link is

established, the LED indicates a

10/100 Mbps connection. If the link

terminates, the LED turns off until

a link is re-established. If the unit

reboots, the LED will again indicate

power until a link is established.

Ports 1-8

PoE

Off No Power over Ethernet

Green 24V Power over Ethernet

Amber 48V Power over Ethernet

Speed/

Link/

Act

Off No link

Amber Link established at 10/100 Mbps

Amber

Flashing Link activity at 10/100 Mbps

Green Link established at 1000 Mbps

Green

Flashing Link activity at 1000 Mbps

Installation Requirements

• Phillips and flathead screwdrivers

• Standard-sized, 19" wide rack with an available 1U space

• For indoor applications, use Category 5 (or above) UTP

cabling approved for indoor use.

• For outdoor applications, shielded Category 5 (or above)

cabling should be used for all wired Ethernet connections

and should be grounded through the AC ground of the

powersupply.

We recommend that you protect your networks from

harmful outdoor environments and destructive ESD events

with industrial-grade, shielded Ethernet cable from Ubiquiti

Networks. For more details, visit www.ubnt.com/toughcable

Important: Although the cabling can be located

outdoors, the TOUGHSwitch itself should be housed

inside a protective enclosure.

WARNING: To reduce the risk of fire or electric shock,

do not expose this TOUGHSwitch to rain or moisture.

WARNING: FAILURE TO PROVIDE PROPER VENTILATION

MAY CAUSE FIRE HAZARD. KEEP AT LEAST 20 MM OF

CLEARANCE NEXT TO THE VENTILATION HOLES FOR

ADEQUATE AIRFLOW.

Hardware Installation

1. Connect the Power Cord to the Power port of each

TOUGHSwitch.

2. Attach the TOUGHSwitch PoE CARRIER to the rack using

the four Phillips Screws. (If the rack has square slots, then

use the Cage Nuts with the Phillips Screws.)

3. Attach the top portion of the faceplate at a slight angle,

and then snap on the bottom portion. Secure the

faceplate to the TOUGHSwitch PoE CARRIER using the two

FlatheadScrews.

4. Connect the other end of each Power Cord to a power

outlet.

Daisy-Chain (Optional)

All data ports are available as uplink ports. If you want to

daisy-chain TOUGHSwitch A and B, we recommend that you

connect an Ethernet cable from port 8 of TOUGHSwitch A to

port1 of TOUGHSwitch B.

Note: PoE is disabled by default on all numbered

ports and is not available on the Management port. To

enable PoE on the appropriate ports, use the Ports tab

in the Configuration Interface.

Accessing the Configuration Interface

Connect to the Configuration Interface by performing the

following steps:

1. Ensure that your computer is connected to the

Management port on the TOUGHSwitch.

Note: By default, you can configure the

TOUGHSwitch via any port; however, we

recommend the Management port. (Access to

the Configuration Interface can be limited to the

Management port only. You can configure this

setting on the Device tab.)

2. Configure the Ethernet adapter on your computer with a

static IP address on the 192.168.1.x subnet

(e.g., 192.168.1.100).

3. Launch your web browser. Type https://192.168.1.20 in

the address field. Press enter (PC) or return (Mac).

4. The login screen will appear. Enter ubnt in the Username

and Password fields. Click Login.

The Configuration Interface will appear, allowing you to

customize your settings as needed.

*640-00056-03*

640-00056-03

Configuring PoE Settings

WARNING: Before activating PoE, ensure that the

connected device supports passive PoE and the

supplied voltage. By default, PoE is off on each port.

1. Click the Ports tab.

2. On the Ports tab, select the Ethernet port you want to

configure. Select the appropriate PoE Status setting, and

then click Save Changes.

The PoE LED on the Ethernet port will confirm the PoE setting.

For detailed instructions on configuring other features,

please refer to the TOUGHSwitch PoE User Guide available at

documentation.ubnt.com/toughswitch

Andere Handbücher für TS-16-CARRIER

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Ubiquiti Schalten Handbücher

Ubiquiti

Ubiquiti US-XG-6POE Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi Switch 24 Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeSwitch 8 Bedienungsanleitung

Ubiquiti

Ubiquiti ES-48-500W Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi US-24-250W Bedienungsanleitung

Ubiquiti

Ubiquiti TS-16-CARRIER Bedienungsanleitung

Ubiquiti

Ubiquiti ES-24-250W Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeSwitch ES-10XP Leitfaden

Ubiquiti

Ubiquiti EdgeSwitch 16XP Bedienungsanleitung

Ubiquiti

Ubiquiti US-16-XG Bedienungsanleitung

Ubiquiti

Ubiquiti FiberPoE Bedienungsanleitung

Ubiquiti

Ubiquiti NanoSwitch N-SW Bedienungsanleitung

Ubiquiti

Ubiquiti US-XG-6POE Bedienungsanleitung

Ubiquiti

Ubiquiti unifi switch 8 Bedienungsanleitung

Ubiquiti

Ubiquiti TouchSwitch Poe TS-5-POE Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeSwitch 8 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi US-8-60W Bedienungsanleitung

Ubiquiti

Ubiquiti US-48 Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeSwitch 48 Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeSwitch 16 XG Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi USW-Pro-24-POE Bedienungsanleitung

Ubiquiti

Ubiquiti US-8-150W Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi USW-16-POE Bedienungsanleitung

Ubiquiti

Ubiquiti US-16-150W Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung

Cabletron Systems

Cabletron Systems GIGAswitch GSR-16 Bedienungsanleitung

Cisco

Cisco Catalyst X4448 Handbuch