Ubiquiti EdgeSwitch 10 XP Bedienungsanleitung

8-Port Gigabit Switch with PoE

and 2 SFP Ports

Model: ES-10XP

Introduction

Thank you for purchasing the Ubiquiti Networks® EdgeSwitch®

10XP. This Quick Start Guide is designed to guide you through

installation and also includes warranty terms.

Package Contents

EdgeSwitch 10XP Wall Mount

Screws (Qty. 2)

Wall Mount

Anchors (Qty. 2)

Ground Screw Power Adapter

(24V, 2.5A)

Power Cord Cable Clip

Installation Requirements

• For indoor applications, use Category 5 (or above) UTP

cabling approved for indoor use.

• For outdoor applications, shielded Category 5 (or above)

cabling should be used for all wired Ethernet connections

and should be grounded through the AC ground of the

power supply.

We recommend that you protect your networks from

harmful outdoor environments and destructive ESD events

with industrial‑grade, shielded Ethernet cable from Ubiquiti

Networks. For more details, visit: www.ubnt.com/toughcable

WARNING: To reduce the risk of fire or electric shock,

do not expose the EdgeSwitch to rain or moisture.

Note: Although the cabling can be located outdoors,

the EdgeSwitch itself should be housed inside a

protective enclosure.

installer’s responsibility to follow local country regulations, including operation within legal

frequency channels, output power, indoor cabling requirements, and Dynamic Frequency

Selection (DFS) requirements.

Hardware Overview

Front Panel Ports

RJ45 Ports 1-8 SFP Ports 9-10

Interface Description

RJ45 1‑8 RJ45 ports support 10/100/1000 Ethernet

connections and 24V Passive Power over

Ethernet (PoE) output.

SFP 9‑10 Hot‑swappable SFP ports support 1 Gbps

connections.

Front Panel Button

Reset

Button Description

Reset

To reset to factory defaults:

1. Disconnect power from the EdgeSwitch.

2. Reconnect power while holding the

Reset button. The port LEDs will light

up in sequential order (this takes

approximately five seconds).

3. When the port 1 LED flashes again,

release the Reset button.

Front Panel LEDs

System

System LED

State Status

Flashing White Bootup in Progress

White

Ready for Use

Not Connected to Ubiquiti® Network

Management System (UNMS™)

Blue Ready for Use

Connected to UNMS

Steady Blue

with Occasional

Flashing

Ready for Use

Unable to Connect to UNMS

Quickly Flashing

Blue Used to Locate a Device in UNMS

Alternating

Blue/White Firmware Upgrade in Progress

You can use the EdgeSwitch Configuration Interface or UNMS

to manage your device. UNMS lets you configure, monitor,

upgrade, and back up your devices using a singleapplication.

Get started at www.unms.com

RJ45 LEDs

Speed/Link/ActivityPoE

LED State Status

PoE

Off No Power over Ethernet

Green 24V Power over Ethernet

Speed/

Link/

Activity

Off No Link

Amber Link Established at 10/100 Mbps

Amber

Flashing Link Activity at 10/100 Mbps

Green Link Established at 1000 Mbps

Green

Flashing Link Activity at 1000 Mbps

SFP LEDs

Link/Activity

LED State Status

Link/

Activity

Off No Link

Green Link Established at 1 Gbps

Green

Flashing Link Activity at 1 Gbps

Back Panel

Power

Grounding Point

Interface Description

Power Connect the included Power Adapter to the

Power port.

Grounding

Point

Ground bonding point for an optional

ground wire.

Side Panel

Ventilation

Holes

Bracket Mounting

Holes

Hardware Installation

The EdgeSwitch can be placed on a horizontal surface,

mounted on a wall, or mounted in a rack (brackets not

included). The optional EdgeRouter™Rackmount Kit, model

ER‑RMKIT, is sold separately.

Follow the Wall Mounting instructions to mount the

EdgeSwitch using the included screws and anchors.

WARNING: FAILURE TO PROVIDE PROPER VENTILATION

MAY CAUSE FIRE HAZARD. KEEP AT LEAST 20 MM OF

CLEARANCE NEXT TO THE VENTILATION HOLES FOR

ADEQUATE AIRFLOW.

WARNING: The EdgeSwitch ES‑10XP must not be stacked.

Do not place it on top of another switch. Do not place

anything on top of the ES‑10XP.

Wall Mounting

To mount the EdgeSwitch on a wall, you will need a drill, a

6mm drill bit, and a Phillips screwdriver.

1. Use a 6 mm drill bit to drill two holes 148 mm apart.

2. Insert the Wall Mount Anchors into the holes. Use a Phillips

screwdriver to secure a Wall Mount Screw to each anchor.

Leave a clearance of approximately 3 mm between each

screw head and its anchor.

148 mm

3 mm

Note: You can also mount the EdgeSwitch in a

vertical orientation.

3. Position the EdgeSwitch with the Ethernet ports facing

down. Place the wall‑mount slots of the EdgeSwitch over

the screw heads on the wall. Then slide the EdgeSwitch

down to lock it into place.

Grounding the EdgeSwitch (Recommended)

The EdgeSwitch is grounded through the Power Adapter;

however, you can add optional ESD grounding for enhanced

ESD protection.

1. Attach the Ground Screw to secure a ground wire (not

included) to the Grounding Point.

2. Optional: To secure the Power Adapter cord, insert it

into the Cable Clip and secure the Cable Clip using the

GroundScrew.

3. Secure the other end of the ground wire to a grounding block.

Connecting Power

1. Connect the Power Adapter to the Power port.

2. Connect the Power Cord to the Power Adapter.

3. Connect the other end of the Power Cord to a power outlet.

Connecting Ethernet

1. Connect an Ethernet cable from your DHCP server or LAN

system to any port on the EdgeSwitch.

2. Connect your computer or host system and other devices

to the other ports on the EdgeSwitch.

Andere Handbücher für EdgeSwitch 10 XP

Inhaltsverzeichnis

Andere Ubiquiti Schalten Handbücher

Ubiquiti

Ubiquiti TS-5-POE ToughSwitchPoE Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeSwitch ES-16-XG Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeRouter PoE ERPoe-5 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi Switch Flex Mini Bedienungsanleitung

Ubiquiti

Ubiquiti USW-Pro-24 Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeSwitch 8 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi US-8-60W Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeSwitch 5XP Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi Switch 48-500W Bedienungsanleitung

Ubiquiti

Ubiquiti USW-24 Bedienungsanleitung

Ubiquiti

Ubiquiti US-16-150W Bedienungsanleitung

Ubiquiti

Ubiquiti USW--Pro--48 Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi US-24-250W Bedienungsanleitung

Ubiquiti

Ubiquiti POE-50-60W Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi USW-Industrial Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi US-8-60W Bedienungsanleitung

Ubiquiti

Ubiquiti US-16-XG Bedienungsanleitung

Ubiquiti

Ubiquiti USW-Industrial Bedienungsanleitung

Ubiquiti

Ubiquiti EdgePoint S16 Bedienungsanleitung

Ubiquiti

Ubiquiti TS-5-POE ToughSwitchPoE Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi Switch 24 US-24-250W Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi USW-Pro-48-POE Bedienungsanleitung

Ubiquiti

Ubiquiti EdgeSwitch 8 150W Bedienungsanleitung

Ubiquiti

Ubiquiti US-8-150W Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung