Ubiquiti Edge Point EP-R8 Bedienungsanleitung

Intelligent WISP Control

with FiberProtect™

Model: EP-R8

Introduction

Thank you for purchasing the Ubiquiti Networks® EdgePoint™

Router. This Quick Start Guide is designed to guide you through

installation and includes the warranty terms.

Package Contents

EdgePoint Router Wall-Mount

Bracket

Metal Straps

(Qty. 2)

Cable Sleeve

Intelligent WISP Control

with FiberProtect™

Model: EP-R8

Gigabit PoE (54V, 1.5A) with

Mounting Bracket

Power Cord Quick Start

Guide

Installation Requirements

• 7 mm socket wrench

• S2 hex wrench

• Ground wire – min. 10 AWG (5 mm2) and max. length: 1m. Asa

safety precaution, ground the EdgePoint to a grounded mast,

pole, tower, or grounding bar.

• Shielded Category 5 (or above) cabling should be used for all

wired Ethernet connections and should be grounded through

the AC ground of the PoE.

• We recommend that you protect your networks from

harmful outdoor environments and destructive ESD events

with industrial-grade, shielded Ethernet cable from Ubiquiti

Networks. For more details, visit: www.ubnt.com/toughcable

warranty. TOUGHCable™is designed for outdoor installations. It is the customer’s responsibility to

follow local country regulations, including operation within legal frequency channels, output power,

and Dynamic Frequency Selection (DFS) requirements.

Introduction

Hardware Overview

Bottom Panel Button

Reset

Button Description

Reset

There are two methods to reset the EP-R8 to

factory defaults:

• Runtime reset (recommended) The

EP-R8 should be running after bootup is

complete. Press and hold the Reset button

for about 10seconds until the eth7 or SFP2

LED starts flashing and then becomes

solidly lit (the SFP 2 LED is used if there is an

SFP module connected to the SFP 2 port).

After a few seconds, the LED will turn off,

and the EP-R8 will automatically reboot.

• Power-on reset Disconnect power from

the EP-R8. Press and hold the Reset button

while connecting power to the EP-R8. Keep

holding the button until the eth7 or SFP 2

LED starts flashing and then stops flashing

after a few seconds (the SFP 2 LED is used

if there is an SFP module connected to the

SFP 2 port).

EdgePoint EP-R8 Quick Start Guide

Bottom Panel Console Port

Console

Interface Description

Console

RJ45 serial console port for Command Line

Interface (CLI) management. Use an RJ45-to-

DB9, serial console cable, also known as a

rollover cable, to connect the Console port to

your computer. (If your computer does not

have a DB9 port, then you will also need a

DB9 adapter.) Then configure the following

settings as needed:

• Baud rate 115200

• Data bits 8

• Parity NONE

• Stop bits 1

• Flow control NONE

Hardware Overview

Power Options

Either the VDC input or PoE input is used at any one time. If both

input types are connected, only the input type with the highest

voltage will be used; the other can be used as a backup. Any of the

input options can power any of the output options.

Power Input Options

• 54VDC, 6A

• 54V, 1.5A on eth0 (PoE In)

• 54V, 1.5A on PoE In

Power Output Options

• EdgePoint (required)

• Passive 54/24V, 4-Pair PoE on

eth1-eth2

• Passive 24V, 2-Pair PoE on

eth3-eth7

The number of devices that can be powered depends on the

power consumption of the specific devices. For example, if you use

54VDC, 1.5A, then you have 81W of power. If the EdgePoint uses

40W (Max. Power Consumption), then you have 41W available for

passive PoE output. Please check product specifications for the

power consumption values to use in your calculations.

Bottom Panel DC Input

VDC

Interface Description

VDC In

Terminal block connector accepts 54VDC,

6A input (including the Ubiquiti Networks

EdgePower™, model EP-54V-150W) to power

the EdgePoint and passive PoE output.

EdgePoint EP-R8 Quick Start Guide

Bottom Panel RJ45 Ports

PoE In

eth0

eth1-2

eth3-7

Interface Description

PoE In

Accepts 54V, 1.5A PoE input from a secondary

PoE adapter (not included) to power the

EdgePoint and passive PoE output.

PoE In / eth0

Accepts data and 54V, 1.5A PoE input from

the included Gigabit PoE Adapter to power the

EdgePoint and passive PoE output.

eth1-2

(54/24V

PoE Out)

RJ45 ports support 10/100/1000 Ethernet

connections and passive 54/24V, 4-pair PoE

output for airFiber® devices.

eth3-7

(24V PoE Out)

RJ45 ports support 10/100/1000 Ethernet

connections and passive 24V, 2-pair PoE

output for airMAX® devices.

RJ45 port eth6 or eth7 is active only if the

corresponding SFP port is empty.

Note: The USB port is reserved for future use.

Hardware Overview

Bottom Panel SFP Ports

SFP 1-2

Interface Description

SFP 1-2

SFP ports are hot-swappable and support

100 Mbps or Gigabit fiber SFP modules. If an

SFP module is plugged in, then the SFP port

is active, and the corresponding RJ45 port is

deactivated.

Front Panel LEDs

LED State Status

eth0

Speed/

Link/Act

Off No Link

Amber 10/100Mbps Link

Flashing Indicates Activity

Green 1000Mbps (1 Gbps) Link

Flashing Indicates Activity

EdgePoint EP-R8 Quick Start Guide

LED State Status

power

Green EdgePoint Powered On

eth1-2

Speed/

Link/Act

Off No Link

Amber 10/100Mbps Link

Flashing Indicates Activity

Green 1000Mbps (1 Gbps) Link

Flashing Indicates Activity

PoE

Output

Off No PoE

Amber 54V Passive

Green 24V Passive

eth3-7

Speed/

Link/Act

Off No Link

Amber 10/100Mbps Link

Flashing Indicates Activity

Green 1000Mbps (1 Gbps) Link

Flashing Indicates Activity

PoE

Output

Off No PoE

Green 24V Passive

SFP 1-2

Speed/

Link/Act

Off No Link

Amber 100Mbps Link

Flashing Indicates Activity

Green 1000Mbps (1 Gbps) Link

Flashing Indicates Activity

Hardware Overview

Back Panel

PicoStation Slot

Lanyard Loop

Pole-Mount

Bracket

Ground

Bonding Point

Lanyard Loop Used for temporary support during installation.

PicoStation®M2HP Slot Used for mounting an optional

PicoStationM2HP (not included) to the back of the EdgePoint. (You

can use the PicoStationM2HP for wireless management of the

EdgePoint.)

Pole-Mount Bracket Used for pole-mounting or in combination

with the included Wall-Mount Bracket for wall-mounting.

Ground Bonding Point Used to secure a ground wire (not

included).

EdgePoint EP-R8 Quick Start Guide

Inhaltsverzeichnis

Andere Ubiquiti Drahtloser Zugangspunkt Handbücher

Ubiquiti

Ubiquiti UniFi nanoHD UAP-nanoHD Bedienungsanleitung

Ubiquiti

Ubiquiti LiteBeam LBE-5AC-16-120 Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam M Bedienungsanleitung

Ubiquiti

Ubiquiti Uni-fi AP Bedienungsanleitung

Ubiquiti

Ubiquiti UAP-AC-PRO Bedienungsanleitung

Ubiquiti

Ubiquiti PowerBeam m5 iso PBE-M5-300-ISO Bedienungsanleitung

Ubiquiti

Ubiquiti Uni-fi AP Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation M Bedienungsanleitung

Ubiquiti

Ubiquiti UAP-AC-PRO Bedienungsanleitung

Ubiquiti

Ubiquiti Rocket M Series Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi AP AC SHD Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi nanoHD AP Bedienungsanleitung

Ubiquiti

Ubiquiti Rocket M3 Bedienungsanleitung

Ubiquiti

Ubiquiti M900 Bedienungsanleitung

Ubiquiti

Ubiquiti Uni-fi AP Bedienungsanleitung

Ubiquiti

Ubiquiti U-Installer Bedienungsanleitung

Ubiquiti

Ubiquiti UniFI UAP-AC Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi UAP-IW-HD Bedienungsanleitung

Ubiquiti

Ubiquiti Rocket 5AC PTP Bedienungsanleitung

Ubiquiti

Ubiquiti Rocket R5AC-Lite Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation AC Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi Bedienungsanleitung

Ubiquiti

Ubiquiti UAP-PRO Bedienungsanleitung

Ubiquiti

Ubiquiti UniFi AP XG Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung

Draytek

Draytek VIGORAP 902 Bedienungsanleitung

EnGenius

EnGenius EAP350 Bedienungsanleitung