Ultimate Lock 3000 Series Bedienungsanleitung

The Ultimate Lock™ 3000 Series Installation Guide

a. This lock is designed for a door that opens into the home or ofce. The lock can be installed on an outward

swinging door, but special instructions are required. Go to the www.theultimatelock.com for details.

b. To provide maximum protection, The Ultimate Lock™ should be installed in a solid 1-3/4” thick wood door or

steel-skinned wood-lled door mounted in a double studded door frame.

c. If your door does not already have a deadbolt installed, it is highly recommended that you purchase an

installation jig kit for deadbolts and door handles. These kits include special hole saws, templates, and other aids

to simplify the installation process. If your door has a metal skin, be sure your kid includes a bi-metal hole saw

If your door jamb/frame is steel, do not remove the hinge screws! See step 2. Check www.theultimatelock.com to

get information on installing the striker plate on a steel door frame.

Congratulations on purchasing the nest deadbolt lock

on the market, The Ultimate Lock™. The Ultimate

Lock™ is engineered to be the best deadbolt lock on the

market. It is vital that your lock is installed properly to

provide the maximum protection possible. Read these

instructions completely before you begin the installation.

More information can be found at our website www.

theultimatelock.com.

• No. 1 and No. 2 Phillips Screw drivers”

No. 1 and No. 2 bits for an electric screwdriver/drill

• Pencil or steel marking pawl

• Electric drill (3/8” chuck) with torque adjustment)

• Drill bits:

1/16"(1.5 mm)

3/32" (2.5 mm)

1/8" (3 mm)

9/64" (3.5 mm)

• Spade bit or forester bit: ¾", and 1"

• Hammer, steel center punch, and 1/2" and 3/4"

chisels

• Small carpenter’s square (adjustable)

• Pliers (2 pair)

• Spray lubricant (WD-40, Silicon Spray, or similar)

• Tape measure or 12-inch ruler

• (If no deadbolt installed) Wood or bi-metal hole

saw: 2 1/8” and 1” wood or bi-metal hole saw

Every Ultimate Lock™ is thoroughly inspected before leaving the factory. It is warranted to be free of defects from workmanship and materials for a period

of TEN YEARS from the date of original purchase. Should any trouble develop during the TEN-year period, return the complete lock system, freight prepaid,

to Ultimate Lock, Inc. at 6150 Richmond Avenue, Suite 209, Houston, TX 77057 or call 1-866-MLS-4005 (1-866-657-4005) for one of Ultimate’s Authorized

Service Centers nearest you. If our inspection shows the trouble was caused by defective workmanship or material, Ultimate Lock™ will repair (or at our

option) replace the lock without charge. Register your Serial Number on line at www. theultimatelocksystems/warranty.com This Warranty does not apply where:

• Repairs have been made or attempted by others

• Repairs are required because of normal wear and tear

• The lock has been abused, misused or improperly installed

• Alterations have been made to the lock or its components

In no event shall Ultimate Lock™ be liable for any indirect, incidental or consequential damages from the sale or use of the product. This disclaimer applies

both during and after the term of the warranty. Ultimate Lock™ disclaims liability for any implied warranties, including implied warranties of “merchantability”

and “tness for a specic purpose”, after the TEN-year term of this warranty. This warranty gives you specic legal rights, and you may also have other

rights, which vary from state to state. Some states do not allow the exclusion or the limitation of incidental or consequential damages, so the above limitation

or exclusion may not apply to you. Some states do not allow limitation on how long an implied warranty lasts, so the above limitation may not apply to you.

*Disclaimer: The Ultimate Lock is only as strong as your door frame. Please contact your local locksmith to visit your home and evaluate your current setup.

Before You Start

Tools You Will Need

A Note About Steel Doors

Limited Warranty

1. Identify Your Parts

Carefully unpack and check that all parts are in the package. Identify parts and hardware from Figure 1. Record the

Serial Number (located inside the lock case) and Date Installed for your lock on the back of this instruction booklet

and save this information for future reference. This information will be required if you ever require any warranty

Key (qty. 2)

Key Lock

Deadbolt

Bar Support

Housing

Lock Bolts

Bar

Gear

Platform

Striker

Decorative Cover

Door Frame

Side

Door

Side

Twist Knob

qty. 2

qty. 6

qty. 2

1 inch (25 mm)

2 inches (50 mm)

3 inches (75 mm)

4 inches (100 mm)

(qty. 1) (qty. 2) (qty. 6) (qty. 6) (qty. 2)(qty. 2)(qty. 2) (qty. 2) (qty. 2)

12 3 4 5 6 789

(Not to scale)

Figure 1

2. Reinforce Your Hinges

3. Measure Your Backset

a. It is very important to reinforce the hinges of your door to get maximum protection from forced entry. Your

Ultimate Lock™ comes with special screws to secure the hinges to the door frame, and not just the jamb board.

b. See Figure 2 and remove half of the existing screws from each of the three hinges as shown in the diagram. If

the screws in the door are machine screws (NOT wood screws), do not remove them. Some metal doors have a

metal hinge side and use machine screws to hold the hinges to the door.

c. Use the special 5" (121 mm) long x 5/32" (4 mm) diameter drill bit provided to drill out the exposed screw holes

all the way into the studs behind the door frame. The longer screws  go in the frame and the shorter screws

 go in the door side of the hinge. NOTE: If the door is ber glass or steel sheeted, do not pre-drill the holes

in the door hinges unless the screws have trouble going into the door. If you run into resistance getting the

screws into the door, STOP, predrill the screw holes, and screw in the shorter screws until snug. If your drill has

adjustable torque, set the torque to slip just as the screw is snug. This is also an excellent time to lightly lubricate

the hinge pins one at a time with a suitable lubricant to stop squeaks and rust.

d. Install the longer screws  into the door jamb, and the shorter screws into the door.

Door Frame

Side

Door

Side

Install longer screws 

into door jamb

Install shorter

screws into door NOTE: Door frame side only gets screws on the inside two holes closest

to center of hinge. Door will either get two screws in center of door or, if

no screws are in center of the door, one screw in the top inside hole and

one screw in bottom outside hole (typically seen on a steel skinned door).

a. For doors with a deadbolt or key lock: Remove the old lock from

the door. Measure the distance from the center of the hole for the old

lock to the edge of the door. It will be either 2 3/8" or 2 3/4". Also

measure the diameter of the hole in the edge of the door for the bolt.

It should be 1 inch (25 mm) in diameter. If the hole is smaller than 1",

use a 1-inch spade drill and expand the hole to the proper size. You

can now skip to step 4.

b. For doors without an existing deadbolt: See Figure 3 and measure

the backset for your door handle/knob. The center of the knob will

either be 2 3/8" or 2 3/4" from the edge of the door. Also measure the

thickness of your door. Write these measurements down.

5½ to 6 inches

Backset

Measurement

Hole must be

1” in diameter.

Drill out if needed.

Figure 2

Figure 3

Your Ultimate Lock™ should be installed 5½ to 6" (127 to 153 mm) ABOVE the

center of the door handle/knob, and the backset should match the door handle/

knob. Measure this distance above the center of the existing door handle/knob

and draw a horizontal line from the door edge back approximately 3 inches on

both sides of the door and across the edge of the door (see Figure 3).

For steel doors with steel door jambs: When installing the Ultimate Lock™ in

steel doors with steel door jambs, the lock must be installed in line with the hole

in the steel door jamb for the deadbolt striker (usually covered with a plate). Place

the paper drilling template (or install jig) on the centerline of the recess, and draw

a line on the door (Figure 4). This will be the centerline for installing the lock in

the door.

4. Locate Your Lock Vertically

5. Measure and Mark Holes

”

(60 MM)

”

(70 MM)

D D

PART # 2

FOLD HERE

30° DRILL

GUIDES

1 " -

(38)

1 " -

(44)

2 " -

(51)

DOOR JAMB

DOOR

6. Prepare Your Door

Refer to the backset measurement recorded in step 3, and determine

the appropriate lock center (A or B) on the paper template. Fold

and place the template on the interior of the door as shown in

Figure 5, and mark the location of pilot hole A or B. Refer to the

door thickness as measured in step b and mark the deadbolt center

hole (G) that matches your door thickness. Mark the two holes

marked D for mounting the bar support.

Backset

Measurement

Place paper template

on interior side of door

”

(60 MM)

”

(70 MM)

D D

PART # 2

FOLD HERE

30° DRILL

GUIDES

1 " -

(38)

1 " -

(44)

2 " -

(51)

These steps are not necessary if you are replacing an

existing deadbolt lock. The hole for the cylinder lock and

deadbolt will already be in place.

a. Using the 5" long 5/32" bit provided, drill the pilot hole

for the lock cylinder as marked in Step 5 (template mark

A or B) to match the backset of the handle/knob).

Make sure the drill bit goes straight through the door.

It is recommended that you drill half way through from

each side of the door.

b. Using the same bit, drill the pilot hole for the deadbolt.

Make sure the drill bit goes in level and the pilot hole is

in the middle of the door.

c. Using a 2 1/8" hole saw, drill out the hole for the lock

cylinder. To prevent splintering, drill through from both sides of the door.

d. Close the door and push a 2 to 2¼" long nail through the deadbolt pilot hole, from inside the cylinder lock hole,

to mark the location for the striker plate hole (Figure 6).

e. Using a 1" hole saw, drill the hole for the deadbolt (Figure 3). Use a sharp chisel to mortise the new deadbolt

faceplate 1/8" (3 mm) deep into the edge of the door.

Push nail through pilot hole

to mark location for center

of striker hole.

Figure 4

Figure 5

Figure 6

7. Install Deadbolt

8. Install Key Lock

a. Look at your door from the inside and note if the hinge is on the right or the left.

b. For a door with hinges on the right, install deadbolt with the cross hole at the bottom. For a door with hinges

on the left, install the deadbolt with the cross hole on top (Figure 7).

c. Drill two 3/32" (2 mm) pilot holes for the two faceplate screws , and then install the screws.

d. Measure off 1 ¼" (31 mm) from the end of the 1/8" (3 mm) drill bit, and mark with a marker or tape.

Cross hole at bottom

for hinges on right

Cross hole at top

for hinges on left

Looking at door from inside:

a. Using the 3/32" (2 mm) drill bit, drill two pilot holes in the (D) locations as marked in step

5. Pilot holes should be ½" deep.

b. Position the bar support ush with the edge of door (Figure 8) and secure in place with

two screws .

c. Hold new key lock in your left hand, and rotate the at blade.

d. With the deadbolt RETRACTED to a at, horizontal position, position the key lock on

the outside of the door, while inserting the at blade (tailpiece) horizontally through the

deadbolt crosshole (Figure 9) .

NOTE: The deadbolt crosshole will be either at the top or bottom of the unit, as

determined in steps 7a and 7b above. Make sure the tailpiece is at (or horizontal) when inserted through the

crosshole.

e. Install the two long lock bolts through the housing and screw them into the key lock. Snug up the lock bolts,

but do not fully tighten them at this point. Make sure the tailpiece does not stick out of the housing, with the

black plastic surface, more than 1/8". If it does, remove the lock and use a pair of pliers to break off the rst

segment of the tail piece. NOTE: Be very careful not to bend the rest of the tailpiece! Now replace the lock

assembly into the door.

CAUTION - DO NOT OVERTIGHTEN THE LOCK

BOLTS IN THE FOLLOWING STEP.

f. Position the housing over the six mounting holes. Using

the square, make sure the housing is square to the edge

of the door, and then tighten lock bolts.

g. Insert the key into the lock and check for correct

operation. You should be able to remove the key at both

the locked and unlocked positions. If the lock does not

function properly, the at blade (tailpiece) is most likely

not positioned correctly.

Bar

Support

Keylock flat

blade/tailpiece

must be horizontal

when inserted

through deadbolt.

NOTE: Bar support

not shown for clarity

Make sure deadbolt

is oriented properly

(See step 4g)

Keylock

Housing

Lock Bolts

Deadbolt

Figure 7

Figure 8

Figure 9

a. Apply a dry, multipurpose lubricant to moving parts (teeth

of gear, and security bar).

b. Position security bar in place and start gear into hole.

c. Align the arrow on the rst tooth of the gear with the

marking corresponding to the backset measurement

previously recorded and engage the gear teeth (Figure 10),

making sure that at tailpiece of key lock properly mates

with gear.

9. Install Security Bar

10. Final Lock Assembly

a. Install platform over assembly and secure in place with six screws .

b. Insert the point of a No. 2 screwdriver into the two mounting holes for the two decorative cover case screws .

Make sure the holes are clear of debris from drilling.

c. Install decorative cover and secure with two case screws  using No. 1 Phillips screwdriver.

d. Use the twist knob and key to exercise the lock. Make sure the lock still turns smoothly. If the lock hangs or

seems to be obstructed while turning, the two case screws  might be contacting the safety bolt. Call Ultimate

Lock for a method of correcting the problem.

e. With security bar retracted, position twist knob in place (oriented vertically), and secure with screw .

Platform

Decorative

Cover

Twist Knob

Housing

PATENT PENDING

Install gear with

alignment mark

matching the

backset measurement

Figure 10

Figure 11

11. Door Jamb Completion

a. Locate and mark centerline of striker on door jamb.

b. For a new lock, locate the mark made in step 6d and drill a

1" diameter hole in door jamb for deadbolt (see step 4d). Use

a 1" hole saw that is 2" long, or a 1" spade bit. Be sure to keep

both bits level and straight through the door frame. Hole

should be 1" (25 mm) deep.

c. Position striker plate on door jamb. Mark holes on door

frame for the 3½” long power screws . (Figure 12).

d. Using the ¾" spade drill bit, drill a hole centered 1/8" in front

of these marks at a 30° angle, 3/8" deep on the deep side of

the hole and 1/8" deep on the shallow side of the hole to allow

for the bulges on the striker plate (Figure 13).

e. Mortise door jamb 3/32" (2.5 mm) deep for the striker. Hold striker plate in place with one hand and close the

door with the other. Make sure that deadbolt and security bar enter the striker plate at the same time. If they

do not, adjust holes and striker plate until they do.

f. Use 3/32" (2.5 mm) bit to drill pilot holes for screws .

Install striker plate and secure with both screws.

g. Close door and use lock key and twist knob to conrm

deadbolt and safety bolt enter striker without interference.

h. Using 5/32" (4 mm) 5" long bit, drill pilot holes at a 30° angle

for power screws . Holes should be 3½" inch (90 mm)

deep.

i. Check the torque adjustment on your drill to avoid

stripping out the screw heads, and install angled power

screws. Use a #2 Philips screw driver to screw the

remainder of the screws to avoid stripping the screw heads.

TIP: Do not force the screws in. If the screws get too tight before they are all the way in, either apply soap to

screw threads, or carefully remove the screw and re-drill the pilot hole and try again.

For steel door frames: If the door jamb is steel you will have to surface-mount the striker plate and drill 25/8"

holes in the steel frame at the point of the mounting holes in the striker plate to accommodate the dimples in

the striker plate. If there is no wood behind the steel frame, you will have to use ¼" x 1" at-head machine

screws with washers and nuts to mount the striker plate. You will need 2¼" x 1" at head machine screws, 2 5/16"

at washers, 2¼" at washers, 2¼" lock washers, and 2¼" nuts. Holding the ¼" screw in the hole, take a pair

of curved, long nose pliers and place the 5/16" washer on the screw, then the ¼" at washer, then the ¼" lock

washer, then the ¼" nut and tighten them down snug.

Mark locations for

holes for power screws 

30°

3/8 inch

1/8 inch

View from top of

door jamb

Mark for

countersink holes

Figure 12

Figure 13

12. Finishing Up

You now have the protection of the Ultimate Lock! To further ensure your safety, it is recommended that you apply

the “Protected by Ultimate Lock System” decal to the door or a nearby window.

“BE SAFE, LOCK UP, AND SET THE INSIDE SAFETY BUTTON WHEN YOU RETIRE”

Operation

Installing on French Doors

The Ultimate Lock™ utilizes two deadbolts that work in unison—a mortise deadbolt and a rim deadbolt. The

secondary rim deadbolt protrudes slightly across the door frame and makes it very easy to verify that your door is

locked. To lock your door, simply turn the twist knob counterclockwise 90° until it is horizontal. To unlock the

door, turn the twist knob clockwise 90° until it is vertical. For even more security, The Ultimate Lock™ features a

patented lockout feature that will prevent ANY key from opening the door. To engage the lockout pin, simply press

the button on the lock until it latches in place. You are now ultimately protected from intrusion!

Additional tools required: rotary cutting tool (Dremel) with metal cutting disc attachment

a. Install lock using regular directions. On French doors, the decorative cover will not t on the door. To x this

problem use a ½ inch chisel and cut into the putty that is blocking the decorative cover.

b. (Omit if threshold for striker plate is made of wood) For doors with metal thresholds, in order to allow room

for the grooves on the striker plate, use metal cutting disc to cut into the metal of the French door allowing

room for the striker plate to t.

French door Top of Door Install

c. Locate an area in the top corner of door where the lock will t. Put bar support in place with edge of support

along the edge of the door. Mark the holes where the screws enter the bar support. Using the drill bit that

comes with the lock, drill holes for the screws. Then attach bar support with screws

.

d. Use the rotary cutting tool with metal cutting attachment to cut the bottom of the

gear ¼" so that gear ts in the housing.

e. Hold the housing in place where the legs are touching the bar support equally on both

sides. Mark all the holes on one side of the housing. Remove housing and put gear,

security bar, and platform in place. Turn the gear and push the lock-out feature in hold

platform and housing together, align platform and housing so that the marks are in the

right place, and mark the correct three holes on the other side. Predrill the correct six

holes and install lock.

Millennium Lock, Inc

6150 Richmond Ave

Suite 210

Houston TX. 77057

Telephone: (713) 975-9642

Fax: (713) 975-9714

For Your Records

For Safe Rooms

For Outward-Opening Doors

It is recommended that you record the details of your Ultimate Lock™ for future reference. This information will

be required if you ever request warranty service.

Installation of the Ultimate Lock™ requires a solid core wood door, a steel door, or a berglas door. The Ultimate

Lock does not work properly on a hollow core door.

For instructions on installing the Ultimate Lock™ on outward-opening doors, please visit our website:

www.theultimatelock.com.

Date Purchased: ______________________________________________________________

Purchased From: ______________________________________________________________

Serial Number: _______________________________________________________________

Inhaltsverzeichnis

Andere Ultimate Lock Sperren Handbücher

Ultimate Lock

Ultimate Lock 3000 Series Bedienungsanleitung

Beliebte Sperren Handbücher anderer Marken

Magic

Magic 105 Bedienungsanleitung

Gantner

Gantner GAT NET.Lock 7020 System Kurzanleitung

Wittkopp

Wittkopp Insys 7202 Bedienungsanleitung

Dorma

Dorma Studio Classic Bedienungsanleitung

Securam

Securam ECSL-601 Bedienungsanleitung

Sudhaus

Sudhaus 3003 Bedienungsanleitung

Safety 1st

Safety 1st 48517 Bedienungsanleitung

Pado

Pado FDS-10 Bedienungsanleitung

Esco

Esco systeQ Series Bedienungsanleitung

COMPX

COMPX National D8951 Bedienungsanleitung

secureo

secureo Key Box Bedienungsanleitung

Stock Loks

Stock Loks C8713 Bedienungsanleitung

COMPX

COMPX 1T-058 Betriebsanleitung

Auslock

Auslock T11 Bedienungsanleitung

ELCOM

ELCOM 7205 Bedienungsanleitung

Stealth SAFES

Stealth SAFES ShadowVault Bedienungsanleitung

Knox

Knox KeySecure 5 Bedienungsanleitung

Kwikset

Kwikset 48334/01 Bedienungsanleitung