Ultrak KC-2A Bedienungsanleitung

INSTALLATION

INSTRUCTIONS

KC-2A

1/3" CCD COLOR

OBSERVATION

CAMERA

Ultrak Worldwide Support Center & Eastern Regional Office:

1301 Waters Ridge Drive Lewisville, TX 75057

(800) 796-2288 (972) 353-6400 FAX (972) 353-6670

Ultrak Western Regional Office:

6252 West 91st Avenue Westminster, CO 80030

(800) 846-8884 (303) 428-9480 FAX (303) 429-6609

ISSUE 1 - July 1996

ISSUE 2 - August 1997

1997 BY ULTRAK

PRINTED IN KOREA

ULTRAK

1301 WATERS RIDGE DRIVE

LEWISVILLE, TX 75057

(972) 353-6400

6252 WEST 91ST AVENUE

WESTMINSTER, CO 80030

(303) 428-9480

BY ANY MEANS WITHOUT WRITTEN PERMISSION FROM ULTRAK.

THE INFORMATION IN THIS PUBLICATION IS BELIEVED TO BE ACCURATE IN ALL

RESPECTS. HOWEVER, ULTRAK CANNOT ASSUME RESPONSIBILITY FOR ANY

CONSEQUENCES RESULTING FROM THE USE THEREOF. THE INFORMATION

CONTAINED HEREIN IS SUBJECT TO CHANGE WITHOUT NOTICE. REVISIONS OR

NEW EDITIONS TO THIS PUBLICATION MAY BE ISSUED TO INCORPORATE SUCH

CHANGES.

iii

USERS OF THE PRODUCT ARE RESPONSIBLE FOR CHECKING

AND COMPLYING WITH ALL FEDERAL, STATE, AND LOCAL LAWS

AND STATUTES CONCERNING THE MONITORING AND

RECORDING OF VIDEO AND AUDIO SIGNALS. ULTRAK SHALL NOT

BE HELD RESPONSIBLE FOR THE USE OF THIS PRODUCT IN

VIOLATION OF CURRENT LAWS AND STATUTES.

IMPORTANT SAFEGUARDS

1. READ INSTRUCTIONS - Read all safety and operating

instructions before operating this product.

2. RETAIN INSTRUCTIONS - Retain the safety and

operating instructions for future reference.

3. CLEANING - Unplug all equipment before cleaning. Do

not use liquid cleaners or aerosol cleaners. Use a damp

cloth for cleaning.

4. ATTACHMENTS - Use only attachments recommended

by the manufacturer. Non-recommended attachments

may result in the risk of fire, electric shock, or injury.

5. WATER AND MOISTURE - Keep all equipment away

from liquids or any other type of moisture.

6. ACCESSORIES - Do not place this television equipment

on an unstable cart, stand or table. The television

equipment may fall causing serious injury to a child or

adult, and serious damage to the equipment. Wall or

shelf mounting should follow the manufacturer’s

instructions, and should use a mounting kit approved by

the manufacturer.

7. POWER SOURCE - The camera should only be

operated from the type of power source indicated in this

Instruction Manual.

8. POWER CORDS - Do not allow anything to rest on the

power cord. Do not locate this product where the cord will

be abused by persons walking on it.

9. LIGHTNING - When this product is left unattended or

unused for long periods of time, unplug it from the power

supply and disconnect it from other equipment. This will

prevent damage to the video product due to lightening

and power-line surges.

10.OVERLOADING - Do not overload wall outlets and

extension cords as this can result in a risk of fire or

electric shock.

11.FOREIGN OBJECTS - Never insert objects of any kind

into this product through openings as they may touch

dangerous voltage points or short-out parts that could

result in a fire or electric shock.

12.SERVICING - Do not attempt to service this product

yourself as opening or removing covers may expose you

to dangerous voltage or other hazards. Refer all servicing

to qualified service personnel.

13.DAMAGE REQUIRING SERVICE - Disconnect the

camera equipment and refer servicing to qualified service

personnel under the following conditions:

a) When the power-supply cord or the plug has been

damaged.

b) If the video product has been exposed to moisture.

c) The video product does not operate normally by

following the operating instructions, adjust only those

controls that are covered by the operating instructions

as an improper adjustment of other controls may

result in damage and will often require extensive work

by a qualified technician to restore the video product

to its normal operation.

d) If the video product has been dropped, or the cabinet

damaged.

When the video product exhibits a distinct change in

performance - this indicates a need for service.

TABLE OF CONTENTS

vii

1.1 PURPOSE ....................................................................................1

1.2 SYSTEM INSTALLATION ............................................................1

1.3 WHITE BALANCE ADJUSTMENT...............................................3

1.4 MANUAL IRIS LENS ADJUSTMENT ...........................................4

1.5 VIDEO-TYPE AUTO IRIS LENS INSTALLATION AND

ADJUSTMENT .............................................................................4

1.6 BACK FOCUS ADJUSTMENT .....................................................5

1.7 ZOOM LENS BACK FOCUS ADJUSTMENT...............................6

2.1 TROUBLESHOOTING .................................................................8

2.2 PREVENTIVE MAINTENANCE....................................................8

SPECIFICATIONS....................................................... Back Cover

SECTION 1

KC-2A CCD COLOR OBSERVATION CAMERA

1.1 PURPOSE

The KC-2A CCD color observation camera provides a low cost

solution to closed circuit television and security surveillance

applications. The KC-2A camera features:

•1/3” interline transfer CCD image sensor

•Supports standard CS- or C-mount lens

•Equipped with electronic iris

•Compatibility with video auto-iris lens

•Excellent picture quality

•Two-year warranty

This manual describes how to setup and operate the KC-2A

Camera.

1.2 SYSTEM INSTALLATION

Installation of the KC-2A camera must be performed by qualified

service personnel in accordance with all local and national

electrical and mechanical codes. Perform the following steps to

install the KC-2A camera.

A. Remove all components from the package and identify the

items that will be used during installation:

•KC-2A camera

•KO-500 camera stand

•KO-60 camera cable

Other items used during the installation that are NOT

supplied with the KC-2A camera may include:

•Camera lens

•Mounting hardware

•Observation monitor

Refer to Figure 1 for identification of the KC-2A camera.

FIGURE 1. KC-2A CAMERA

B. Select a suitable location for the camera. Install the camera

stand or mounting bracket in the selected location using a

suitable fastener. The camera stand or mounting bracket

must be attached to a structural object, such as a wall stud

or ceiling rafter, that will support the weight of the camera

and mount.

C. The KC-2A camera has a threaded mounting hole on the

bottom and top of the camera housing to allow for bottom or

top mounting. The ¼"-20 UNC threaded mounting hole

attaches to the bolt on the camera stand or mounting

bracket.

NOTE: Do not aim or point the camera towards the sun or

into a strong light.

D. Attach a CS-mount lens directly to the front of the camera

lens mount. If a C-mount lens is used, the CS/C back focus

ring must be adjusted to the “C” setting.

E. If an auto-iris lens is used, connect the cable to the terminal

block for a video-type auto-iris lens.

F. Route the assembled cable from the monitor to the camera.

G. Plug the cable into the connector port labeled “MONITOR” on

the rear of the camera.

H. Plug the other end of the cable into the corresponding

camera connector port on the rear of the monitor.

I. Adjust the lens focus and iris controls for an optimum picture.

1.3 WHITE BALANCE ADJUSTMENT

This adjustment is used to place the white balance function of the

camera into the AUTO (Automatic) or MANU (Manual) mode. If

the switch is placed in the AUTO position, the camera will

automatically try to maintain white objects as white even if the

light color changes. If the switch is placed in the MANU position,

the user can adjust the R (Red) and B (Blue) controls until white

objects are seen as white on the monitor. The MANU position is

primarily used when viewing objects under colored lights.

Inhaltsverzeichnis

Andere Ultrak Sicherheitskamera Handbücher

Ultrak

Ultrak CSC100BU Bedienungsanleitung

Ultrak

Ultrak KD6 Z Series Betriebsanleitung

Ultrak

Ultrak KD5 Series Bedienungsanleitung

Ultrak

Ultrak DuraCam VK74A36C Bedienungsanleitung

Ultrak

Ultrak KC4500MN Bedienungsanleitung

Ultrak

Ultrak HEB10 Bedienungsanleitung

Ultrak

Ultrak KC2200CN Bedienungsanleitung

Ultrak

Ultrak KC5300 Bedienungsanleitung

Ultrak

Ultrak KC6300 Bedienungsanleitung

Ultrak

Ultrak KC5520CN Bedienungsanleitung

Ultrak

Ultrak TVC-500 Bedienungsanleitung

Ultrak

Ultrak KC4300E Bedienungsanleitung

Ultrak

Ultrak KC450xMP Bedienungsanleitung

Ultrak

Ultrak KC7400CN Bedienungsanleitung

Ultrak

Ultrak KC-3P Bedienungsanleitung

Ultrak

Ultrak KC452xMx Series Bedienungsanleitung

Ultrak

Ultrak HEG14 Bedienungsanleitung

Ultrak

Ultrak KC440xMP Bedienungsanleitung

Ultrak

Ultrak KD6 Z-SERIES Montageanleitung

Ultrak

Ultrak DuraCam Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung