Uniden XDECT R003 Bedienungsanleitung

XDECT R003

Bluetooth®

For more exciting new products please visit our website:

Australia: www.uniden.com.au

New Zealand: www.uniden.co.nz

XDECT R003BT Accessory Handset

Owner's Manual

XDECT R003BT

accessory

handset and

charger

(with stand)

What's in the box?

Battery

cover

Rechargeable

battery pack (BT-694s)

Repeater/Charger

adapter

(AAD-041S(M))

If any items are missing or damaged, contact your place of

purchase. Never use damaged products!

Need Help? Get answers at our website:

www.uniden.com.au for Australian model or www.uniden.co.nz

for New Zealand model.

Important Safety Instructions!

When using your telephone equipment, basic safety precautions should always be

followed to reduce the risk of re, electric shock and injury to persons, including the

following:

This unit is NOT waterproof.

DO NOT expose this unit to rain or moisture.

Do not use this product near water, for example, near a bath tub, wash bowl, kitchen



sink or laundry tub, in a wet basement or near a swimming pool.

Avoid using a telephone (other than a cordless type) during an electrical storm. There



may be a remote risk of electric shock from lightning.

Do not use the telephone to report a gas leak in the vicinity of the leak.



Use only the power cord and batteries indicated in this manual. Do not dispose of



batteries in a re. They may explode. Check with local codes for possible special

disposal instructions.

Do not place the handset in any charging cradle without the battery installed and the



battery cover securely in place.

SAVE THESE INSTRUCTIONS!

Setting Up Your Handset

Install the Battery

1. Unpack the handset, battery pack, and

battery cover. If the battery cover is

already on the handset, press in on the

notch and slide the cover down and off.

Line up the battery pack2.

connector with the jack inside the handset. (The battery connector

only fits one way.)

Push the battery pack connector in until it clicks into place. Tug3.

gently on the wires to make sure the battery pack is securely

connected.

Place the cover over the battery4.

compartment and slide it up into

place.

Connect the Charger

Connect the AC adapter to the charger's1.

DC IN 9V

jack and route the cord as

shown. (This adapter might already be

connected.)

Plug the other end of the adapter into a2.

standard 240V AC power outlet.

Place the handset in the charger with the display facing forward.3.

The display on the handset should turn on.

If... Try...

the display on the

handset does not turn

reseating the handset.-

checking the AC adapter-

connection.

Charge the handset completely (about 15 hours)

before using it.

Registering the Handset

The accessory handset will not work until you register it to

a base! Registering the handset is a separate process from

registering the Repeater/ charger. You can use the handset

normally even if the charger is not registered.

Compatible Bases

This handset is designed for use with Uniden's XDECT R035BT

base. For the most up-to-date list of compatible bases for this

handset, see our website.

Place the handset in the base. The display should say

Handset

Registering

After about 30 seconds, the handset display should say

Registration Complete

Test the connection

Pick up the handset and press

TALK

. Make sure you get a dial tone.

(Press

END

to hang up.)

If... Try...

you don't hear a dial tone-

the display says-

Registration

Failed

Making sure the handset is fully charged,

then trying again.

To use your XDECT R003BT with your Bluetooth phones, see

the manual that came with XDECT R035BT base.

Using the Repeater/Charger

How it Works

The XDECT R003BT repeater/charger extends the range of your

base in all directions, including up and down. Each handset will

automatically connect to the repeater/charger or the base,

depending on which signal is stronger. (The handset operates

exactly the same way whether it's connected to the base or to the

repeater/charger.)

To use the charger's repeater function, you must register the



charger to an XDECT R035BT base. (Any repeater/chargers that

came packaged with the base are already registered to that base

for you.)

An XDECT R035BT base can support up to six XDECT R003BT



repeater/chargers, including any that were supplied with your

phone.

Usually, you can't tell when a handset switches between the



base and the repeater/charger in the middle of a call, but

sometimes, you might notice a brief pause in your conversation.

Repeaters can be up to 3 chain-links (maximum) from the base

Base Coverage Area

Handsets in this area always

connect to the base.

Overlap Coverage

Area

Handsets in this

area might connect

to the base or the

charger.

Extended Coverage Area

Handsets in this area

always connect to the

charger.

Base

Repeater/charger

Registering the Repeater/charger

Registering the Repeater/charger is a separate process from

registering the handset. You can use the charger even if the

handset is not registered.

On the base, press and hold1.

FIND

when the phone is in standby.

2. On the bottom of the repeater/charger,

press and hold the registration

button until the

LINK

light starts to

blink (about 2 seconds).

Release the button and wait for3.

the

LINK

light to turn on and steady

(this can take about 90 seconds).

If the

LINK

light doesn't

turn on,

disconnect

the charger's AC adapter. Wait about ten

seconds, then try these steps again.

Some important things to remember:

Only register one charger at a time. If more than one charger



is in registration mode at the same time, they can interfere with

each other.

If you want to use the repeater/charger with a different base, just



erases the link to the old base when it registers to the new one.

Only register chargers to one base at a time. If more than one



base is in registration mode at the same time, you can't control

which base the charger registers to.

Placing the repeater/charger

Here are a few tips for placing your repeater/charger so that you get

the clearest signal and the maximum range:

Make sure you have good reception from the base.



Put the charger

at least 10m away from the base or any other

charger. (If you put the charger on a different floor from the base,

don't forget to allow 10m vertically, also.)

If possible, mount the charger on the wall.



Picking the best spot

The best spot for the repeater/

charger is as far from the

base as possible while still

maintaining a good signal,

or near the edge of the

base’s coverage area. To

find the edge of the

coverage area:

Stand near the base1.

and make a call on the

handset.

While on the call, carry2.

the handset away

from the base towards the general area where you want to put the

charger.

Watch the signal strength icon on the handset. Make a note where3.

the icon drops from 4 bars to 3 bars.

Continue walking away from the base. Make a note where the signal4.

strength icon drops from 3 bars to 2 or if you start to hear noise on

the line (which indicates the signal is getting weaker).

Place the charger anywhere inside the range where the signal5.

strength icon showed 3 bars and the handset had a clear signal with

no noise.

Testing the location

Connect the charger's AC adapter and make sure the

LINK

light

comes on steadily. If the light flashes, the repeater/charger is not

getting a good signal from the base. The charger may be too far

away from the base, there may be interference from electronic

devices, or the signal might be blocked by thick walls or metal

objects. Try moving the charger to another location.

Wall Mounting the Repeater/charger

If you want mount the charger on the wall, you need to adjust the

desk stand:

Pull the locking tab up and1.

back (see the black arrow in the

illustration to the right), and slide

the desk stand straight off.

Flip the stand over so the locking2.

tabs that say

WALL

are facing the

charger with the arrows pointing

down.

3. Align the stand with the

notches on the charger.

Slide the stand onto the4.

notches until it clicks into

place.

Insert two #10 screws into the5.

wall, 30 mm apart. (For best

results, use a level to ensure

the screws are even.)

Remember to use

appropriate anchors for the

wall material.

Keeping the AC adapter cord6.

out of the way, place the

charger over the screw heads

and slide it down into place.

Switching back to the

desk stand

If you want to switch back to

using the charger on a desktop:

Remove the stand.1.

Rotate the stand so that the locking tabs that say2.

DESK

are facing

the charger with the arrows pointing up.

Align the stand with the notches on the charger.3.

Slide the stand onto the notches until it clicks into place.4.

Important Information

Handling Liquid Damage

Moisture and liquid can damage your cordless phone.

If the handset or repeater/charger is exposed to moisture or



liquid, but only the exterior plastic housing is affected, wipe off

the liquid, and use as normal.

If moisture or liquid has entered the plastic housing (i.e. liquid



can be heard in the phone or liquid has entered the handset

battery compartment or vent openings on the base), follow these

steps:

Handset Repeater/charger

Remove the battery cover and disconnect1.

the battery.

Let dry for at least 3 days with the battery2.

disconnected and the cover off for

ventilation.

After the handset dries, reconnect the battery3.

pack and replace the cover. Recharge the

battery fully (15-20 hours) before using.

Disconnect the AC adapter to cut off1.

the power.

Let dry for at least 3 days before2.

reconnecting.

IMPORTANT: You must unplug the telephone line while recharging

the battery pack to avoid charge interruption.

CAUTION! DO NOT use a microwave oven to speed up

the drying process. This will cause permanent damage

to the handset, base and the microwave oven.

Specications

Use only the supplied AC adapter.



Be sure to use the proper adapter for



the base and any chargers.

Do not place the power cord where it



creates a trip hazard or where it could

become chafed and create a re or

electrical hazard.

Do not place the unit in direct sunlight



or subject it to high temperatures.

adapter

Part number AAD-041S(M)

Input voltage 240V AC, 50Hz

Output voltage 9V DC@ 350mA

Battery

pack

Part number BT-694s

Capacity 500mAh (BT-694s)

Battery Information

Fully charged, the battery should provide about 10 hours of talk time and about 7 days



of standby time. For best results, return the handset to the cradle after each call to

keep it fully charged.

Keep an eye on the battery status icon. When the battery gets too low, the handset



shows a low battery alert. If you hear a strange beep during a call, check the display:

if you see the low battery alert, nish your conversation as quickly as possible and

return the handset to the cradle. If the handset is in standby, none of the keys will

operate.

With normal use, the battery should last about one year. Replace the battery when



the talk time becomes short even when the battery is charged. To buy a replacement

battery, visit the website; www.uniden.com.au for Australian model or www.uniden.

co.nz for New Zealand model.

Rechargeable Nickel-Metal-Hydride Battery Warning

CAUTION! Risk of explosion if battery is replaced by an

incorrect type! Dispose of used batteries according to

the instructions. Do not open or mutilate the battery.

Disconnect the battery before shipping this product.

This equipment contains a rechargeable Nickel-Metal-Hydride battery.



The rechargeable batteries contained in this equipment may explode if disposed of in



a re.

Do not short-circuit the battery.



Do not charge the rechargeable battery pack used in this equipment with in any



charger other than the one designed to charge this battery pack as specied in the

owner's manual. Using another charger may damage the battery pack or cause the

battery pack to explode.

Rechargeable Batteries Must Be Recycled or Disposed of Properly.

Uniden works to reduce lead content in PVC coated cords in our products &

accessories.

Andere Handbücher für XDECT R003

Inhaltsverzeichnis

Andere Uniden Schnurloses Telefon Handbücher

Uniden

Uniden WXI377 Bedienungsanleitung

Uniden

Uniden DCT756 Series Service-Handbuch

Uniden

Uniden EXAI5680 - EXAI 5680 Cordless Phone Bedienungsanleitung

Uniden

Uniden XCAI680 Bedienungsanleitung

Uniden

Uniden TRU9260 - TRU 9260 Cordless Phone Bedienungsanleitung

Uniden

Uniden TRU348 Bedienungsanleitung

Uniden

Uniden DECT2088 - DECT 2088 Cordless Phone Base... Bedienungsanleitung

Uniden

Uniden DECT180 Service-Handbuch

Uniden

Uniden DCX300 - DCX 300 Cordless Extension Handset Bedienungsanleitung

Uniden

Uniden TCX930 - TCX 930 Cordless Extension Handset Bedienungsanleitung

Uniden

Uniden DXAI 5188-2 Series Bedienungsanleitung

Uniden

Uniden TRU9280 Series Bedienungsanleitung

Uniden

Uniden CLX 465 SERIES Bedienungsanleitung

Uniden

Uniden EXT1265 Bedienungsanleitung

Uniden

Uniden AS1052 Series Bedienungsanleitung

Uniden

Uniden 6035 + 1 Bedienungsanleitung

Uniden

Uniden DECT 3035 Bedienungsanleitung

Uniden

Uniden ELT 560 series Bedienungsanleitung

Uniden

Uniden TRU9480 Series Bedienungsanleitung

Uniden

Uniden DECT2080-2 - DECT Cordless Phone Benutzerhandbuch

Uniden

Uniden TRU9360 Series Bedienungsanleitung

Uniden

Uniden XS 910 Bedienungsanleitung

Uniden

Uniden TRU241 Bedienungsanleitung

Uniden

Uniden DXI5686-2 - DXI Cordless Phone Service-Handbuch

Beliebte Schnurloses Telefon Handbücher anderer Marken

3Com

3Com NBX Bedienungsanleitung

Panasonic

Panasonic KX-TGK210HK Bedienungsanleitung

Panasonic

Panasonic KX-TCA181EX Bedienungsanleitung

BT FREESTYLE 3200 Bedienungsanleitung

AT&T

AT&T CL84102 Bedienungsanleitung

BREZZICNI

BREZZICNI CL-3622 Bedienungsanleitung

Panasonic

Panasonic KX-TG1831NZ Bedienungsanleitung

Panasonic

Panasonic KX-TG7301E Bedienungsanleitung

Sanyo

Sanyo CLT-J70 Bedienungsanleitung

Amplicomms

Amplicomms BigTel 201 Bedienungsanleitung

GE 26992 Bedienungsanleitung

AT&T

AT&T E1812B Bedienungsanleitung

Sanyo

Sanyo CLT-670 Bedienungsanleitung

GE 15432970 Bedienungsanleitung

Curtis

Curtis TC595 Bedienungsanleitung

Gigaset

Gigaset Gigaset 3000 Micro Bedienungsanleitung

Poly

Poly VVX D230 Einrichtungshandbuch

AT&T

AT&T 7625 Bedienungsanleitung