Uniden XDECT R006 Bedienungsanleitung

XDECT R006

For more exciting new products please visit our website:

Australia: www.uniden.com.au

New Zealand: www.uniden.co.nz

XDECT R006 OM.indd 1 15/6/10 2:13:15 PM

XDECT R006 Accessory Handset

Owner's Manual

XDECT R006

accessory

handset and

charger

What's in the box?

Belt

clip

Battery

cover

Rechargeable

battery pack

(BT-694 or BT-694s)

AC adapters for

Repeater (AAD-

041S(M))and Charger

(AAD-600S(M))

If any items are missing or damaged, contact your place of

purchase. Never use damaged products!

Need Help? Get answers at our website:

www.uniden.com.au for Australian model or www.uniden.co.nz

for New Zealand model.

Important Safety Instructions!

When using your telephone equipment, basic safety precautions should always be

followed to reduce the risk of re, electric shock and injury to persons, including the

following:

This unit is NOT waterproof.

DO NOT expose this unit to rain or moisture.

Do not use this product near water, for example, near a bath tub, wash bowl, kitchen



sink or laundry tub, in a wet basement or near a swimming pool.

Avoid using a telephone (other than a cordless type) during an electrical storm. There



may be a remote risk of electric shock from lightning.

Do not use the telephone to report a gas leak in the vicinity of the leak.



Use only the power cord and batteries indicated in this manual. Do not dispose of



batteries in a re. They may explode. Check with local codes for possible special

disposal instructions.

Do not place the handset in any charging cradle without the battery installed and the



battery cover securely in place.

SAVE THESE INSTRUCTIONS!

Repeater, desk-stand,

wallmount screws and

plug cover

XDECT R006 OM.indd 2 15/6/10 2:13:18 PM

Setting Up Your Handset

Install the Battery

1. Unpack the handset, battery pack, and

battery cover. If the battery cover is

already on the handset, press in on the

notch and slide the cover down and off.

2. Line up the battery pack

connector with the jack inside the

handset. (The battery connector only fits

one way.)

Push the battery pack connector in until it3.

clicks into place. Tug gently on the wires

to make sure the battery pack is securely

connected.

Place the cover over the battery4.

compartment and slide it up into

place.

Connect the Charger

Connect the AC adapter1.

to the charger's

DC IN 9V

jack and route the cord as

shown. (This adapter might

already be connected.)

Plug the other end of the2.

adapter into a standard

240V AC power outlet.

Make sure that the charge

LED illuminates when the

handset is seated.

XDECT R006 OM.indd 3 15/6/10 2:13:20 PM

Place the handset in the charger with the display facing forward.3.

The

CHARGE

light should turn on.

If... Try...

the

CHARGE

light

does not turn on

reseating the handset.-

checking the AC adapter-

connection.

Charge the handset completely

(about 15 hours) before using it.

Registering the Handset

The accessory handset will not work until you register it to

a base! Registering the handset is a separate process from

registering the Repeater. You can use the handset normally

even if the repeater is not registered.

Compatible bases

This handset is designed for use with Uniden's XDECT R055 base.

For the most up-to-date list of compatible bases for this handset, see

our website.

Place the handset in the base. The display should say

Handset

Registering

After about 30 seconds, the handset display should say

Registration Complete

Test the connection

Pick up the handset and press

TALK

. Make sure you get a dial tone.

(Press

END

to hang up.)

If... Try...

you don't hear a dial tone-

the display says-

Registration Failed

Making sure the handset is fully charged,

then trying again.

Attaching the Belt Clip

Line up the holes on each side of the handset. Insert the belt clip

into the holes on each side of the handset. Press down until it clicks.

To remove the belt clip, pull either side of the belt clip to release the

tabs from the holes.

Make sure that the charge

LED illuminates when the

handset is seated.

XDECT R006 OM.indd 4 15/6/10 2:13:21 PM

Using the Repeater

How it Works

The XDECT R006 repeater works to extend the range of the XDECT

R055 base in just the same way as the repeater/charger unit. The

only difference is the XDECT R006 repeater and handset-charger

are separate units. Refer to your XDECT R055 owner's manual page

8 for more information on how repeaters work.

To use the repeater function, you must register the repeater to



an XDECT R055 base. (Any repeaters that came packaged with

the base are already registered to that base for you.)

An XDECT R055 base can support up to six XDECT R006



repeaters, including any that were supplied with your phone.

Usually, you can't tell when a handset switches between the



base and the repeater in the middle of a call, but sometimes, you

might notice a brief pause in your conversation.

Connect the Repeater

Remove the repeater Plug Cover from the



plug section.

Connect the AC adapter to the repeater's



DC IN 9V jack and route the cord as

shown.

Place the repeater Plug Cover over the



plug section and slide into place. Plug the

other end of the adapter into a standard 240V AC power outlet.

XDECT R006 OM.indd 5 15/6/10 2:13:22 PM

Registering the Repeater

Registering the Repeater is a separate process from registering

the handset.

On the base, open the menu and select1.

2. On the bottom of the repeater,

press and hold the registration

button until the

LINK

light starts to

blink (about 2 seconds).

Release the button and wait for3.

the

LINK

light to turn on and steady

(this can take about 90 seconds).

If the

LINK

light doesn't

turn on,

disconnect

the repeater's AC adapter. Wait about ten

seconds, then try these steps again.

Some important things to remember:

Only register one repeater at a time. If



more than one repeater is in registration

mode at the same time, they can interfere

with each other.

If you want to use the repeater with a different base, just register



the repeater to the new base. The repeater automatically erases

the link to the old base when it registers to the new one.

Only register repeaters to one base at a time. If more than one



base is in registration mode at the same time, you can't control

which base the repeater registers to.

Placing the Repeater

Here are a few tips for placing your repeater so that you get the

clearest signal and the maximum range:

Make sure you have good reception from the base.



Put the repeater

at least 10m away from the base or any other

repeater. (If you put the repeater on a different floor from the

base, don't forget to allow 10m vertically, also.)

If possible, mount the repeater on the wall.



XDECT R006 OM.indd 6 15/6/10 2:13:23 PM

Picking the best spot

The best spot for the repeater

is as far from the base as

possible while still

maintaining a good signal,

or near the edge of the

base’s coverage area. To

find the edge of the

coverage area:

Stand near the base1.

and make a call on the

handset.

While on the call, carry2.

the handset away

from the base towards the general area where you want to put the

repeater.

Watch the signal strength icon on the handset. Make a note where3.

the icon drops from 4 bars to 3 bars.

Continue walking away from the base. Make a note where the signal4.

strength icon drops from 3 bars to 2 or if you start to hear noise on

the line (which indicates the signal is getting weaker).

Place the repeater anywhere inside the range where the signal5.

strength icon showed 3 bars and the handset had a clear signal with

no noise.

Testing the location

Connect the repeater's AC adapter and make sure the

LINK

light

comes on steadily. If the light flashes, the repeater is not getting a

good signal from the base. The repeater may be too far away from

the base, there may be interference from electronic devices, or the

signal might be blocked by thick walls or metal objects. Try moving

the repeater to another location.

XDECT R006 OM.indd 7 15/6/10 2:13:24 PM

Wall Mounting the Repeater

You can mount the repeater directly to a wall using the horizontally

aligned mounting slots at the back of the repeater unit. Before doing

this consider the following:

Avoid electrical cables, pipes, or other items behind the mounting



location that could cause a hazard when inserting screws into

the wall.

Mount the repeater within distance of a working 240V AC power



outlet.

Note! The Repeater unit is NOT waterproof. If mounted onto

an outside wall place under an eave or roof overhang where it

is protected from direct weather conditions, DO NOT place in

direct sunlight.

Insert the supplied two #101.

screws into the wall, 60 mm

apart. (For best results, use

a level to ensure the screws

are even.) Remember to use

appropriate anchors for the

wall material.

Keeping the AC adapter2.

cord out of the way, place

the repeater over the screw

heads and slide it down into

place.

Desk Mount the Repeater

You can also desk mount the

repeater by inserting the desk mount stand

into the slots at the back of the unit.

3mm 60mm

27.5mm

XDECT R006 OM.indd 8 15/6/10 2:13:26 PM

Important Information

Handling Liquid Damage

Moisture and liquid can damage your cordless phone.

If the handset, repeater, or charger is exposed to moisture or



liquid, but only the exterior plastic housing is affected, wipe off

the liquid, and use as normal.

If moisture or liquid has entered the plastic housing (i.e. liquid



can be heard in the phone or liquid has entered the handset

battery compartment or vent openings on the base), follow these

steps:

Handset Repeater or charger

Remove the battery cover and disconnect1.

the battery.

Let dry for at least 3 days with the battery2.

disconnected and the cover off for

ventilation.

After the handset dries, reconnect the battery3.

pack and replace the cover. Recharge the

battery fully (15-20 hours) before using.

Disconnect the AC adapter to cut off1.

the power.

Let dry for at least 3 days before2.

reconnecting.

IMPORTANT: You must unplug the telephone line while recharging

the battery pack to avoid charge interruption.

CAUTION! DO NOT use a microwave oven to speed up

the drying process. This will cause permanent damage

to the handset, base and the microwave oven.

Specications

Use only the supplied AC adapters.



Be sure to use the proper adapter for



the base and any repeater or charger.

Do not place the power cord where it



creates a trip hazard or where it could

become chafed and create a re or

electrical hazard.

Do not place the unit in direct sunlight



or subject it to high temperatures.

adapter

Part number AAD-041S(M) /

AAD-600S(M)

Input voltage 240V AC, 50Hz

Output voltage 9V DC@ 350mA / 9V

DC@210mA

Battery

pack

Part number BT-694 or BT-694s

Capacity 650mAh (BT-694) or

500mAh (BT-694s)

XDECT R006 OM.indd 9 15/6/10 2:13:27 PM

Battery Information

Fully charged, the battery should provide about 8 hours of talk time and about 7 days



of standby time. For best results, return the handset to the cradle after each call to

keep it fully charged.

Keep an eye on the battery status icon. When the battery gets too low, the handset



shows a low battery alert. If you hear a strange beep during a call, check the display:

if you see the low battery alert, nish your conversation as quickly as possible and

return the handset to the cradle. If the handset is in standby, none of the keys will

operate.

With normal use, the battery should last about one year. Replace the battery when



the talk time becomes short even when the battery is charged. To buy a replacement

battery, visit the website; www.uniden.com.au for Australian model or www.uniden.

co.nz for New Zealand model.

Rechargeable Nickel-Metal-Hydride Battery Warning

CAUTION! Risk of explosion if battery is replaced by an

incorrect type! Dispose of used batteries according to

the instructions. Do not open or mutilate the battery.

Disconnect the battery before shipping this product.

This equipment contains a rechargeable Nickel-Metal-Hydride battery.



The rechargeable batteries contained in this equipment may explode if disposed of in



a re.

Do not short-circuit the battery.



Do not charge the rechargeable battery pack used in this equipment with in any



charger other than the one designed to charge this battery pack as specied in the

owner's manual. Using another charger may damage the battery pack or cause the

battery pack to explode.

Rechargeable Batteries Must Be Recycled or Disposed of Properly.

Uniden works to reduce lead content in PVC coated cords in our products &

accessories.

XDECT R006 OM.indd 10 15/6/10 2:13:27 PM

Andere Handbücher für XDECT R006

Inhaltsverzeichnis

Andere Uniden Schnurloses Telefon Handbücher

Uniden

Uniden XS 916 Bedienungsanleitung

Uniden

Uniden EXT1160 Bedienungsanleitung

Uniden

Uniden XDECT 8355 Series Bedienungsanleitung

Uniden

Uniden EXA 3955 Bedienungsanleitung

Uniden

Uniden DECT1480 Bedienungsanleitung

Uniden

Uniden EXI4246 - EXI 4246 Cordless Phone Bedienungsanleitung

Uniden

Uniden WDECT3355 Bedienungsanleitung

Uniden

Uniden EXI 3965 Bedienungsanleitung

Uniden

Uniden DCT5260 Bedienungsanleitung

Uniden

Uniden EXI3226 - EXI 3226 Cordless Phone Bedienungsanleitung

Uniden

Uniden DSS7815 +1 Series Bedienungsanleitung

Uniden

Uniden DXAI5588-3 Series Bedienungsanleitung

Uniden

Uniden D1660 Bedienungsanleitung

Uniden

Uniden EXP 6900 SERIES Bedienungsanleitung

Uniden

Uniden BLUETOOTH XDECT R035BT Bedienungsanleitung

Uniden

Uniden EXP4541 Series Service-Handbuch

Uniden

Uniden DECT1825 Bedienungsanleitung

Uniden

Uniden MC480 Bedienungsanleitung

Uniden

Uniden DXI386 Bedienungsanleitung

Uniden

Uniden TWX977 Series Bedienungsanleitung

Uniden

Uniden UIP1869V Bedienungsanleitung

Uniden

Uniden EXS 9995 Bedienungsanleitung

Uniden

Uniden DXI 7284-2 Series Bedienungsanleitung

Uniden

Uniden EXP2240 Bedienungsanleitung

Beliebte Schnurloses Telefon Handbücher anderer Marken

3Com

3Com NBX Bedienungsanleitung

Panasonic

Panasonic KX-TGK210HK Bedienungsanleitung

Panasonic

Panasonic KX-TCA181EX Bedienungsanleitung

BT FREESTYLE 3200 Bedienungsanleitung

AT&T

AT&T CL84102 Bedienungsanleitung

BREZZICNI

BREZZICNI CL-3622 Bedienungsanleitung

Panasonic

Panasonic KX-TG1831NZ Bedienungsanleitung

Panasonic

Panasonic KX-TG7301E Bedienungsanleitung

Sanyo

Sanyo CLT-J70 Bedienungsanleitung

Amplicomms

Amplicomms BigTel 201 Bedienungsanleitung

GE 26992 Bedienungsanleitung

AT&T

AT&T E1812B Bedienungsanleitung

Sanyo

Sanyo CLT-670 Bedienungsanleitung

GE 15432970 Bedienungsanleitung

Curtis

Curtis TC595 Bedienungsanleitung

Gigaset

Gigaset Gigaset 3000 Micro Bedienungsanleitung

Poly

Poly VVX D230 Einrichtungshandbuch

AT&T

AT&T 7625 Bedienungsanleitung