Uniden DS810 Bedienungsanleitung
QUICK START
GUIDE
Digital Spread Spectrum
provides the longest range,
the clearest sound
and the best privacy.
DS
810
CONTENTS
Installation and Safety
Quick Start Guide
Accessories Included in Your Package
Controls and Functions
Installing the Beltclip
Headset Installation
Recharging the Handset
Adjusting the Ringer and Earpiece
Volume
Travelling out of Range
Key Lock/Unlock
Call Waiting/Flash
Paging the Handset
Making and Receiving Calls
Troubleshooting
Warranty
Start
Here!
Quick Start Guide - next page
This symbol indicates
important operating and
servicing instructions.
PRECAUTIONS
INSTALLATION & SAFETY
Choosing the best location for your DS810
When choosing a location for your phone there are a number of appliances the phone
should not be near, and areas you should avoid.
AVOID -
Television sets and
other electronic
appliances AVOID -
Microwave
ovens
AVOID -
Computers
AVOID -
Moisture
AVOID -
Other Cordless
phones
3
AVOID -
Connecting
more than
phones as Ringing
may be impaired.
CHARGE -
the new phone
for 15 - 20 hrs
and raise the
antenna before
making a call. DON’T -
overload the
power oulet. AVOID -
moisture
CHOOSE -
a central location
!
3
This page is a very condensed version of the Owners Manual. It is designed
to allow you to get your phone installed and operating as quickly as possible
- however it does not attempt to explain any of the advanced features of the
DS810
.
Start
Here!
Quick Start Guide
Installing
the Base Unit
Raise the antenna.
(Australia)
the AC Adaptor into
AC Adaptor cord
AC Adaptor cord
Make sure the AC
Adaptor remains
switched ON at all
times.
Use only the Uniden
AC Adaptor supplied
with this unit.
!
Phone socket
(New Zealand)
AC Adaptor Power point
Telephone cord
1
Position the battery in the compartment and
slide the cover into place.
Installing the
Handset Battery
Press the battery cover and slide it off.
Connect the battery plug to the socket at the
rear of the battery compartment.
Make sure the plug is the right way
round.
The RED and BLACK battery wires must
match the RED and BLACK printed on the
phone case for the plug to fit properly.
Press firmly until it clicks into place.
Place the handset on the base Unit and
charge it uninterrupted for 20 hours.
Making a Call
Handset on Base Unit:
Remove the handset from the base and
speak (Auto Talk).
Handset off the Base Unit:
Pick up the handset, press and
speak.
To hang up - press again OR
place the handset on the base unit.
Answering a Call
Pick up the handset and press .
Dial the phone number
OR
Dial the phone number - then press .
To hang up - press
OR
Place the handset on the base Unit.
talk
talk
talk talk
talk
ION
fire,
T860
BLACK
RED
NOTE
2
CONTROLS & FUNCTIONS
Other printed materials
ACCESSORIES INCLUDED IN YOUR PACKAGE
Rechargeable Battery AC Adaptor
Belt Clip
If any of these items are
missing or damaged, contact
your place of purchase.
TelephoneCord
Telephone Cord
Adaptor
(Australia Only)
This Owner’s Manual
Consumer Support Card
NOTE
Headset jack
Belt clip slot
Battery compartment
Redial
Talk key
Not functional
Handset aerial
Handset speaker
Flash
Call waiting/Battery low
Volume control keys
Numeric keypad
Not functional
Not functional
Handset Microphone
Not functional
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
15
16
1
1
23
4
5
7
6
8
9
0
#
pqrs
ghi
abc def
mno
jkl
wxyz
tuv
talk
c/w
redial
flash
vol
SPREAD SPECTRUM
900MHz DIGITAL
3
4
22
23
Charging contacts
Base unit aerial
Status LED
Page key
Telephone line
AC Adaptor input
Registration button
18
19
20
21
22
23
24
18
19
21
Rear of Base Unit
Top of Base Unit
DIGITAL SPREAD SPECTRUM
page
status
20
900MHz
19
24
5
6
FEATURES
l
l
l
l
l
l
l
l
l
l
l
900MHz Digital Spread Spectrum Technology
Backlit Keypad
Flash
7 Days Standby Battery Life
8 Hours Talk Time
Handset Earpiece and Ringer Volume Control
Hearing Aid Compatible
Last Number rRedial
Call Waiting
Page / Find
Headset Jack
Battery use time (per charge)
From fully charged
Four and half hours continuous use.
Ten days when the handset is in the standby mode.
A full charge will take at least 12 hours if Low Battery is displayed - however the
phone will be ready for a short call after one hour.
When the battery charge becomes low
If the phone is not in use, Low Battery flashes and none of the keys will operate. If
the phone is in use, Low Battery flashes and the handset beeps. Complete your
conversation as quickly as possible and return the handset to the base unit for charging.
Use only the genuine
Uniden Battery supplied
with your phone.
Replacement batteries are
also available through the
Uniden Parts Department.
The built-in memory
backup can hold numbers
and names stored in the
memory even if the
battery pack is completely
discharged.
NOTE
NOTE
Cleaning the battery contacts
To maintain a good charge, it is important to clean the battery contacts on the handset
and base unit with a dry cloth or a pencil eraser about once a month.
Do not use any liquids or solvents.
BATTERY MAINTENANCE
You cannot over charge the battery.
You may return the handset to the charger after each call or when the battery is low.
Genuine handset batteries
The high quality rechargeable batteries supplied with your phone perform for up to
two years or more. In order to enjoy the best performance from your phone, we
recommend you replace your batteries every two years with a genuine Uniden Battery.
Simply order a replacement battery from:
Uniden Australia PTY Limited Uniden New Zealand Limited
Service Division Service Division
Toll Free: 1300 366 895 Toll Free: 0800 4 UNIDEN (0800 4 864 336)
www.uniden.com.au www.uniden.co.nz
If you are using an
optional headset, you
must still use the handset
keypad for phone
operations.
!
headset
jack
Your phone may be used with an optional
headset.
To use this feature, simply plug the headset
into the headset jack.
HEADSET INSTALLATION
To attach the beltclip
INSTALLING THE BELTCLIP
l
Press the beltclip against the rear of the
handset until it clicks into place.
To remove the beltclip
l
Gently pull one side of the beltclip
to release.
1
23
4
5
7
6
8
9
*
0
#
pqrs
ghi
abc def
mno
jkl
wxyz
tuv
talk
c/w
redial
flash
vol
SPREAD SPECTRUM
900MHz DIGITAL
ADJUSTINGTHERINGERANDEARPIECEVOLUME
Ringer tone and volume
The phone has four ringer tone and volume combinations.
In the standby mode, press or on the handset repeatedly to select the desired
setting.
The telephone will keep this setting for all calls.
The phone has four earpiece volume settings
7
Ring A Low Ring A Loud Ring B LoudRing B Low
!
Normally it is not
necessary to register your
handset. These
instructions are for
reference only.
CALLWAITING/FLASH
If the Call Waiting tone sounds during a call -
Australia: Press , then to switch between callers.
New Zealand: Press to switch between callers.
When an incoming call is
received during paging,
pagingiscancelled andthe
telephone is switched to
the incoming call.
NOTE
NOTE
For Call Waiting to
operate, you must first
subscribe to a Call Waiting
service through your
telephone company.
KEY LOCK/UNLOCK
When the handset is not in use, press and hold , a beep confirms
the key pad is locked. During the ‘Key Locked’ condition, the keys will only operate to
answer an incoming call. To unlock the keys, press and hold again.
flash
flash
During a call, noise will increase if you move your handset too far from your base unit.
If the range limit of your base unit is exceeded, your call will terminate within 30 seconds.
TRAVELLING OUT OF RANGE
flash
flash
2
1. Press on the base.
2. The handset beeps for 60 seconds.
3. Press the button on the base again
to end the page.
PAGINGTHEHANDSET
page
page
1. Remove the handset from the base unit.
2. Press then
3. Place the handset on the base unit.
4. Press and Hold the registration button (Located near the DC power Jack at the rear
of the base). A long tone confirms when registration is completed.
The handset included with your phone is already registered to the base.
REGISTRATION
flash
1
8
1
23
4
5
7
6
8
9
*
0
#
tone
pqrs
ghi
abc def
mno
jkl
wxyz
tuv
oper
talk
c/w
redial
flash
vol
USING
YOUR NEW PHONE
MAKING AND RECEIVING CALLS
When Handset
Off Base
To answer
a call
(phone ringing)
To hang up
Basic phone operation
button
Pick up handset
1.
Auto talk answers the call as
soon as the handset is picked up
(AutoStandby)
1.
Return the handset to the
base. Press on the handset
To make
a call
Pick up handset
2.
3.
1.
Enter the phone number Pick up handset
2.
3.
1.
Enter the phone number
Press
Press
talk
talk talk
talk
To redial
1. Pick up the handset
3. Listen for the dial tone
4. Press
If any key is pressed
before
pressing
, the last
number dialled will
not redial
2. Press 2. Listen for the dial tone
3. Press
1. Press
NOTE
talk
talk
Press
talk
redial redial
When Handset
On Base
redial
1. 1.
9
1
23
4
5
7
6
8
9
*
0
#
pqrs
ghi
abc def
mno
jkl
wxyz
tuv
talk
c/w
redial
flash
vol
SPREAD SPECTRUM
900MHz DIGITAL
Inhaltsverzeichnis
Andere Uniden Telefon Handbücher
Uniden
Uniden DECT1588-2 Bedienungsanleitung
Uniden
Uniden 1035 Series Bedienungsanleitung
Uniden
Uniden D3588 Bedienungsanleitung
Uniden
Uniden WDECT2385 Bedienungsanleitung
Uniden
Uniden XDECT 6145BT Series Bedienungsanleitung
Uniden
Uniden EVOC2 Bedienungsanleitung
Uniden
Uniden 3162 Series Bedienungsanleitung
Uniden
Uniden Trimline Phone Bedienungsanleitung
Uniden
Uniden DECT 1515 Bedienungsanleitung
Uniden
Uniden DXAI5588-3 Series Bedienungsanleitung
Uniden
Uniden Extend-A-Phone EX945 Bedienungsanleitung
Uniden
Uniden FP101 Bedienungsanleitung
Uniden
Uniden FP098 Bedienungsanleitung
Uniden
Uniden DECT2188-3 - DECT Cordless Phone Base... Service-Handbuch
Uniden
Uniden WDSS 5315 Bedienungsanleitung
Uniden
Uniden FP103 Bedienungsanleitung
Uniden
Uniden DCX210 Bedienungsanleitung
Uniden
Uniden 1380 Bedienungsanleitung
Uniden
Uniden CXAI5198 Service-Handbuch
Uniden
Uniden CEZAI998A Service-Handbuch
