Uniden UH060SX-2 Bedienungsanleitung

UH060SX-2

Operating Guide

To bring outstanding wireless communication products

to people's lives throughout the world.

vol/ch

UT928ZH_UH060_ENG_0929 9/29/04 3:26 PM Page 1

vol/ch

CONTROL & INDICATORS

INCLUDED IN YOUR PACKAGE:

•UH060SX Radio (2)

•Operating Guide

•Belt Clip (2)

OPTIONAL ACCESSORIES

•VOX Earset

•Carry Case

1 Antenna

2 PTT (Push-To-Talk) Button

3 Monitor Button

4 Duplex/Call Key

5 Scan Key

6 Channel/Volume/Keylock Key

7 Speaker

8 Headset Jack

9 Volume/Channel up Key

10 Volume/Channel down Key

11 Power On/Off/Select Key

12 Txp/CTCSS Key

13 Microphone

•Charging Cradle with AC Adaptor

•NiMH Battery Pack (2)

•VOX Headset (2)

14 Battery Level Meter

15 Receive Indicator

16 Channel Indicator

17 Scan Indicator

18 VOX Indicator

19 Keypad Lock Indicator

20 Transmit Indicator

21 Volume Setting Indicator

22 HI Indicator

23 LO Indicator

24 CTCSS Indicator

25 Charging LED’s

UT928ZH_UH060_ENG_0929 9/29/04 3:26 PM Page 2

GETTING STARTED

BATTERY INSTALLATION

Your UH060SX-2 unit uses the included NiMH battery pack for

power. The unit can be powered with optional 4 AAA ALKALINE

batteries.

To avoid damage to the unit do not mix old and

new batteries.

Do not charge alkaline or non rechargeable

batteries.

Uniden does not represent this product to be

waterproof. Do not expose this product to Rain or

Moisture.

If you don't use the UH060SX-2 for long periods,

Uniden recommend removing the batteries. The

UH060SX-2 is designed to retain the previous user

settings. This feature will continue to use a small

amount of battery power while the unit is switched off.

To install the batteries:

1. Make sure your radio is off.

2. Release the battery cover clip, then

remove the battery cover.

3. Insert NiMH battery pack according

to the orientation on the battery

pack.

OR Insert 4 AAA ALKALINE batteries (not

included) according to the polarity

symbols inside the battery

compartment.

4. Align the battery cover tabs with the

UH060SX-2 tab holes then replace

the cover clip.

UT928ZH_UH060_ENG_0929 9/29/04 3:26 PM Page 3

Place the UH060SX-2 into the charge cradle. The charge light will

come on to indicate the unit is charging. Before operating the

UH060SX-2, charge the battery pack for 16 hours.

If the battery level becomes low, the battery

indicator icon on the display begins flashing.

When the batteries in the unit are low, the unit will go into a

Battery Low mode. The Transmit mode is disabled. Replace the

alkaline batteries immediately or if you are using the NiMH

battery pack, place the radio on the charge cradle to recharge.

Full charge will take up to 16 Hrs.

Do not charge alkaline or non

rechargeable batteries.

BELT CLIP

LOW BATTERY ALERT

To attach the belt clip:

Slide the belt clip until it snaps into place.

To remove the belt clip:

To remove the belt clip, press and hold belt

clip locker, slide the belt clip at the same

time until released.

INSTALLING THE CHARGE CRADLE

•Plug the AC adaptor into the rear of the charge cradle and

into the mains power.

UT928ZH_UH060_ENG_0929 9/29/04 3:26 PM Page 4

OPERATION

POWER ON/OFF

Press and hold

select/power

key to turn the

radio on. A channel number will appear on the

display. Press and hold

select/power

key to

turn the radio off.

VOLUME

Press

volume/channel

▲or ▼key to

increase or decrease the volume level.

‘VOL’

icon appears on the display while

volume is being adjusted.

There are 8 volume levels. Level 0 (No Audio)

to Level 7 (Maximum Volume).

ADJUSTING THE KEY BEEPS

Your radio emits a beep each time one of the keys (except for

the PTT button) is pressed.

To turn OFF this beep: Press and hold

dup/call

key while

turning on the radio.

To turn ON this beep: Press and hold

dup/call

key while turning

on the radio.

ROGER BEEP

Roger Beep is a BEEP that is sent to notify the end of

transmission (both PTT and VOX transmission.) Roger Beep can

be heard through the speaker when Key Beep is on. Roger Beep

is transmitted even if Key Beep is turned off. However, Roger

Beep will not be heard from the speaker.

To turn OFF Roger Beep: Press and hold

volume/channel

▲

key while turning on the radio.

To turn ON Roger Beep: Press and hold

volume/channel

▲

key while turning on the radio.

UT928ZH_UH060_ENG_0929 9/29/04 3:26 PM Page 5

SELECTING A CHANNEL

•Press

ch/vol/keylock

key momentarily

to activate channel select mode. The

displayed channel will flash.

•Press

volume/channel

▲or ▼key to

select the desired channel.

•Press

ch/vol/keylock

key momentarily

to exit channel select mode.

•If no button is pressed within 4 sec the

UH060SX-2 will exit from the channel

select mode.

TO TRANSMIT AND RECEIVE

The UH060SX-2 uses the 40 UHF-CB Channels. For your

reference a list of the available channels and corresponding

frequencies is printed on page 11.

1. Before you transmit, listen for activity

on the selected channel.

2. When the channel is clear, press and

hold the PTT button to transmit.

‘TX’

icon appears on the display.

Hold the radio with microphone approximately 5 cm in front

of your mouth with the antenna at approximately 45° angle

away from your head. Speak in a clear, normal

conversational voice.

3. When you have finished speaking, release the PTT and listen

for a response.

‘TX’

icon then disappears on the display.

While receiving, the

‘RX’

icon is displayed.

UT928ZH_UH060_ENG_0929 9/29/04 3:26 PM Page 6

AUTOMATIC SQUELCH FEATURE

The UH060SX-2 is equipped with an Automatic Squelch System

which shuts off weak transmissions and unwanted noise.

MONITOR

This feature enables users to listen for weak

signals on the current channel at the press of a

button.

To use monitor:

•Press

moni

button. The

‘RX’

icon will flash.

•Release within 1.5 seconds and the unit exits Monitor mode.

•Press and hold

moni

button for 2 seconds for continuous

listening.

The receiver circuit will stay open, letting in both the noise &

weak signals. The

‘RX’

icon flashes in this status.

•To return to normal Receive mode press

moni

button. The

‘RX’

icon disappears or stops flashing in this status.

TRANSMIT Hi/Lo POWER SELECT

•Press

txp/ctcss

key momentarily to select

desired transmit level.

•

‘HI’

icon will appear on the display for

maximum transmit level.

•

‘LO’

icon will appear on the display for

minimum transmit level.

•No transmit level appears for the middle

transmit level

•The RF transmit power of the UH060SX-2 is

selectable between 0.1/0.5/1.5 W.

UT928ZH_UH060_ENG_0929 9/29/04 3:26 PM Page 7

TO OPERATE IN DUPLEX MODE (REPEATERS)

The Duplex function enables you to access local repeater

stations. You can only activate Duplex from CH01-CH08.

UHF CB Repeaters are used to retransmit or relay your signal.

Repeaters will extend the range of your radio and overcome the

shielding effect caused by solid obstructions.

SCANNING

The scan function scans all channels and stops at an active

channel. When the signal stops, the UH060SX-2 waits 2 seconds

(Reply Delay) before scanning resumes.

Press

dup/call

key momentarily. The

changes to .

Press

dup/call

key again to deactivate the

duplex operation. UH060SX-2 will return to

normal operation.

Operation with the aid of a Repeater

Contact your retailer for a list of repeaters

available in your area.

dup/call

key is pressed when the channel is not

from CH01 - CH08, an error tone sounds.

UT928ZH_UH060_ENG_0929 9/29/04 3:26 PM Page 8

REPLY DELAY

While scanning, the UH060SX-2 stops at a

busy channel and receives a transmission.

When the received signal is over, the unit

will wait for 2 seconds for the return of the

signal, otherwise, the radio resumes scanning.

To initiate scanning,

1. Press

scan

key momentarily to begin

scanning. The

‘SCAN’

icon is displayed.

2. Press

select/power

key or

scan

key to

cancel.

CTCSS (Continuous Tone Coded Squelch System)

CTCSS is a feature that allows a group to talk to each other

without hearing other users on the same channel.

Press and hold

txp/ctcss

key for 3 seconds in Standby mode to

enter CTCSS mode.

The current selected CTCSS tone flashes.

Press

volume/channel

▲or ▼key to select the required

CTCSS tone (OFF or 1-38).

For channels with a CTCSS tone setting, the CTCSS tone is

displayed below the channel indicator. For channels with the

setting of CTCSS OFF, there will be no display below the channel

indicator.

Press

txp/ctcss

key to confirm the selected setting.

Channels 5 and 35 are used for emergency channels.

CTCSS will not operate on these channels.

VOX

VOX is the automatic transmitting function by inputting voice into

the VOX headset mic without pressing the PTT button.

Press

select/power

key momentarily while in standby mode to

enter VOX Sensitivity mode.

UT928ZH_UH060_ENG_0929 9/29/04 3:26 PM Page 9

TRANSMITTING A CALL TONE

Your UH060SX-2 radio is equipped with 5 selectable call tones

that will be transmitted when the

dup/call

key is pressed and

held for 3 seconds.

To select a call tone:

1. Press

select/power

key momentaly twice while in standby

mode to enter Call Tone mode. The current call tone number

(C1-C5) will be indicated.

2. Press the

volume/channel

▲or ▼key to increase or

decrease the number to the desired call tone. Each tone will

be heard through the speaker.

3. Press

select/power

key to confirm and exit to standby

mode.

To transmit the selected call tone, press and hold the

dup/call

key. The selected tone will automatically be transmitted for a fixed

length of time. Call Tone will be cancelled when the PTT button is

pressed.

KEYLOCK ON/OFF

Press

ch/vol/keylock

key for 3 seconds to enter keylock on

mode.

Press

ch/vol/keylock

key for 3 seconds while in Keylock mode

to exit the Keylock mode.

While in Keylock on mode, the UH060SX-2 can still

receive and transmit.

The current selected VOX setting will flash on the display.

Press

volume/channel

▲or ▼key to adjust the VOX

sensitivity. 1 is the highest sensitivity and 4 is the lowest

sensitivity. VOX can be turned off by selecting

‘oF’

icon.

The

‘VOX’

icon is shown on the display when VOX is selected to

on and VOX Headset is plugged into VOX Headset Jack. The

‘TX’

icon blinks when the voice level is possible to transmit at the

current selected VOX sensitivity level.

Press

select/power

key twice to confirm the setting and exit to

standby mode.

UT928ZH_UH060_ENG_0929 9/29/04 3:26 PM Page 10

Inhaltsverzeichnis

Andere Uniden Zwei-Wege-Funkgerät Handbücher

Uniden

Uniden Atlantis 290 Bedienungsanleitung

Uniden

Uniden GMR1448-2CK Bedienungsanleitung

Uniden

Uniden ecoterra GMR1088-2CK Bedienungsanleitung

Uniden

Uniden GMR2238-3CKDC Konfigurationshandbuch

Uniden

Uniden GMR2872-2CK Bedienungsanleitung

Uniden

Uniden ecoterra GMR645-2CK Bedienungsanleitung

Uniden

Uniden MHS450 Bedienungsanleitung

Uniden

Uniden FRS420 Bedienungsanleitung

Uniden

Uniden ATLANTIS250 BK - ATLANTIS 250 VHF Radio Benutzerhandbuch

Uniden

Uniden GMR1448-2CK Bedienungsanleitung

Uniden

Uniden FRS400 Bedienungsanleitung

Uniden

Uniden GMR2238-2CK Bedienungsanleitung

Uniden

Uniden UH044DP Bedienungsanleitung

Uniden

Uniden GMR2240-2CK Konfigurationshandbuch

Uniden

Uniden SUNDOWNER UH-056 Bedienungsanleitung

Uniden

Uniden PC68XL Bedienungsanleitung

Uniden

Uniden BEARCAT 880 Bedienungsanleitung

Uniden

Uniden EcoTerra GMR1838-2CK Bedienungsanleitung

Uniden

Uniden UH047sx Bedienungsanleitung

Uniden

Uniden GMR1438-2 Bedienungsanleitung

Uniden

Uniden FRS440 Bedienungsanleitung

Uniden

Uniden MHS450 Bedienungsanleitung

Uniden

Uniden GMR325-2 Bedienungsanleitung

Uniden

Uniden GMR1635-2 Konfigurationshandbuch

Beliebte Zwei-Wege-Funkgerät Handbücher anderer Marken

Midland

Midland 70-1526A/B Bedienungsanleitung

HYT

HYT TC700 Bedienungsanleitung

DNT

DNT Space100 Bedienungsanleitung

Legacy

Legacy ProLine Series Bedienungsanleitung

Evolveo

Evolveo FreeTalk XM2-2 Bedienungsanleitung

AWC

AWC AWR1688+ Bedienungsanleitung

Motorola

Motorola XT665d Bedienungsanleitung

Cobra

Cobra 2-Way Radio Bedienungsanleitung

Klutch

Klutch KR-400 Bedienungsanleitung

Garmin

Garmin Rino 655t Bedienungsanleitung

Motorola

Motorola TLK 150 Bedienungsanleitung

Midland

Midland MXT275J Bedienungsanleitung

Titan

Titan TR200 Bedienungsanleitung

Cobra

Cobra CXT645 Bedienungsanleitung

Tait

Tait TM9100 Bedienungsanleitung

Yaesu

Yaesu FT-65R Bedienungsanleitung

Motorola

Motorola ASTRO SRX 2200 Series Bedienungsanleitung

Motorola

Motorola T5583 Bedienungsanleitung