United Technologies Kidde VS1 Bedienungsanleitung

Page 1 of 8 DATA SHEET V85005-0135

Not to be used for installation purposes. Issue 1.1

Kidde Catalog uSmall Building Fire Alarm Solutions

11-17-16

Technology that saves lives

Overview

Kidde brand intelligent life safety systems offer the power of high-

end intelligent processing in conﬁgurations that deliver uncompli-

cated solutions for small to mid-sized applications. With intelligent

detection, electronic addressing, automatic device mapping,

optional Ethernet®connectivity, and a full line of easily-conﬁgured

option cards and modules, these ﬂexible systems offer versatility

that beneﬁts building owners and contractors alike.

The VS1 provides one Class A or Class B intelligent device loop

that supports up to 64 device addresses, and two Class B Notiﬁ-

cation Appliance Circuits (NACs). Optional Class A device wiring is

available with the use of a module.

The VS4 provides one Class A or Class B intelligent device

loop that supports up to 250 device addresses. Loop controller

modules may be added in combination to expand total system

capacity in 250-point increments to up to 1,000 device addresses.

VS4 panels include four NACs that may be wired for either Class A

or Class B operation.

The RZI16-2 module adds even more capacity to VS installations

by adding up to 16 conventional device circuits and two additional

notiﬁcation appliance circuits. This makes them ideal retroﬁt solu-

tions that can accommodate new intelligent detectors, as well as

existing conventional devices.

VS Series supports a wide range of high-end features, including:

• Intelligent modules, detectors, and bases

• GSA-REL Releasing Modules

• R-Series remote annunciators

• Integrated Carbon Monoxide gas sensing with V-PCOS de-

tectors including distinct audible signaling

Features

• Auto-programming speeds installation time

• Supports V-Series intelligent modules and detectors

• Form C contacts for alarm and trouble, Form A for supervisory

• Electronic addressing with automatic device mapping

• Optional Ethernet port for diagnostics, programming and a

variety of system reports

• Two programmable switches with LEDs and custom labeling

• Supports Genesis horn silence over two wires, and UL

1971-compliant strobe synchronization

• Supports GSA-REL releasing module for ﬁre suppression

• Class B or Class A wiring

• Ground fault detection by module

• Supports up to eight serial annunciators, (LCD, LED-only, and

graphic interface)

• Can use existing wiring for most retroﬁt applications

• Upload/download remotely or locally

• Two-level maintenance alert reporting

• Pre-alarm and alarm veriﬁcation by point

• Adjustable detector sensitivity

• 4 x 20 character backlit LCD display

• Optional earthquake hardening: seismic Importance Factor 1.5

• Standalone operation

• Transmission test frequency by hour

Intelligent Fire

Alarm Systems

VS1, VS4

7165-1657:

0244

S3000

COA 6229

Page 2 of 8 DATA SHEET V85005-0135

Not to be used for installation purposes. Issue 1.1

11-17-16

Application

Kidde VS Series life safety systems are powerful intelligent solutions

for small to mid-sized buildings. Advanced intelligent technology

delivers the beneﬁts of ﬂexible system installation, while clean and

easy-to-operate user interfaces make panel operation and system

maintenance quick and intuitive.

The smart choice

Electronic addressing eliminates the tedium of setting dipswitches,

and automatic device mapping ensures that each device resides

on the system at its correct location. Meanwhile, innovative pro-

gramming allows the designer to customize the system to pre-

cisely suit the needs of the building owner.

Reliability you can count on

The inherent fault-tolerant characteristics of Analog/Address-

able Technology boosts the reliability of Kidde ﬁre alarm systems.

When combined with VS Series smoke and heat detectors, these

systems deliver a level of dependability not previously available

for small to mid-sized applications. All Kidde systems are built to

exacting reliability benchmarks and meet international standards

for quality, in addition to agency listings for dependability.

Clear-cut remote annunciation

Remote annunciation is a strong suit of the VS Series ﬁre alarm

systems. Up to eight annunciators can be installed on a single

system. Compatible annunciators include a range of LED and LCD

models that provide zone or point annunciation, as well as com-

mon control capabilities. VS control panels also supports graphic

annunciation with optional graphic annunciator interface modules.

Each interface provides common control and 32 LEDs.

Dimensions

(1) Surface Mounting Holes

(2) Semi-ﬂush mounting Holes

(3) Backbox with Door Attached

(4) Backbox with door and trim kit attached.

Panel dimensions, in (cm)

Model D1* D2 D3 D4 D5* D6 D7 D8 D9

VS4 28.0

(71.1)

3.85

(9.8)

9.0

(22.8)

22.0

(55.8)

15.75

(40.0)

10.25

(26.0)

4.9

(12.4)

30.1

(76.4)

2.7

(6.8)

VS1 21.5

(54.6)

3.85

(9.8)

7.5

(19.0)

15.5

(39.4)

14.25

(36.2)

10.25

(26.0)

4.9

(12.4)

23.6

(59.9)

2.7

(6.8)

* Add 1-1/2 in. (3.81 cm) to D1 and D5 dimensions for trim kit. The trim kit

provides 0.75 inches (1.9 cm) of trim to the top, bottom, and sides of the backbox.

Programming and remote diagnostics

Kidde VS Series life safety systems are simple to set up, yet offer

advanced programming features that put these small building

panels into a class of their own. The auto programming feature

quickly gets the panel operational using factory default settings.

Basic zone and point settings can be programmed through the

front panel interface, so the system is up and running in no time.

For more advanced system conﬁguration and correlation groups

programming, VS Series systems interface to a PC running com-

patible VS-CU software. This option offers full system conﬁgura-

tion in the familiar Windows®operating environment. Connection is

made to a laptop through the panel’s optional RS-232 communi-

cations port, which can also be used to connect a system printer.

Among the many innovative features of VS Series control panels

is the optional network card. This module provides a standard

10/100 Base T Ethernet®network connection that permits access

to the control panel from any remote location with the correct

communications protocols. The connection can be used to down-

load to the panel from the VS-CU, or upload and view system

reports using the VS-CU.

Available system reports include:

• Correlation groups • Device details

• Device maintenance • History

• Internal status • System conﬁguration

• System status • Walk test

• Dialer • CO runtime

Flexibility built right in

Two fully-programmable front panel switch/LED combinations pro-

vide an added measure of ﬂexibility. Their slide-in labels take the

mystery out of custom applications, and present a clean ﬁnished

appearance.

Perfect for retroﬁts

Kidde VS Series control panels are particularly well-suited to

retroﬁt applications. All connections are made over standard wiring

– no shielded cable required. This means that in most situations

existing wiring can be used to upgrade a legacy control panel

to VS technology without the expense or disruption of rewiring

the entire building. VS control panels also support the ingenious

RZI16-2 zone module, which adds up to 16 conventional circuits

and two NACs. This combination easily accommodates new intel-

ligent detection alongside existing conventional circuits, making it

an superior solution in the retroﬁt market.

Signals with a difference

VS Series NACs are conﬁgurable to fully support the advanced

signaling technology of Kidde Genesis and Enhanced Integrity no-

tiﬁcation appliances. These devices offer precision synchronization

of strobes to UL 1971 standards. For Genesis devices, enabling

this feature allows horns to be silenced while strobes on the same

two-wire circuit continue to ﬂash until the panel is reset.

A complete line of accessories

VS Series life safety systems are supported by a complete line of

analog/addressable detectors, modules and related equipment.

Consult the Ordering Information section for details.

Page 3 of 8 DATA SHEET V85005-0135

Not to be used for installation purposes. Issue 1.1

11-17-16

Each VS1 panel ships with one device loop controller that sup-

ports 64 devices of any type. This panel’s device capacity cannot

be expanded.

System Layout

VS4

Each VS4 panel has room for up to two device loop

controller modules in any combination of single or

dual 250-device loops. VS4 comes with one loop

that supports up to 125 detectors and 125 modules.

VS1

Panel Layout

1Transformer

2Main AC wiring block & fuse holder

3RS-232 card connector (J3)

4Dialer card connection (J8)

5Ethernet card connector (J1)

6Main circuit board

7Panel backbox enclosure

8Operator interface

9SLC card connector (J7)

10 Class A card connector (J2)

11 Tie wrap mounts

12 LED expander connector (J6)

13 Standby batteries

00:00:00 01/01/07

Four Class B or two optional Class A NACs

Up to 20,000 feet of wiring per loop

Four Class B or two optional Class A NACs

Optional 10 A or 6.5 A Booster

Up to eight remote annunciators

Up to 125 sensors and 125 modules per loop

Ethernet (SA-ETH)

DACT/Dialer (SA-DACT)

RS-232 (SA-232)

Relays: Two Form C, one Form A

Standard Loop: 250 points (one expansion slot)

V-SLC2-1 Expander Loop: 250 points (one expansion slot)

V-SLC2-2 Expander, Loop 1 of 2: 250 points

V-SLC2-2 Expander, Loop 2 of 2: 250 points

Any combination of two single- or dual device loop modules

(one expansion slot)

Sixteen Conventional IDCs,

two additional NACs with RZI16-2 module

Ethernet (SA-ETH)

DACT/Dialer (SA-DACT)

RS-232 (SA-232)

Relays: Two Form C, one Form A

Up to 20,000 feet of wiring.

Two Class B or two optional Class A NACs

Optional 10 A or 6.5 A Booster Power Supply

Up to eight remote annunciators

Loop supports up to 64 intelligent devices of any type.

Page 4 of 8 DATA SHEET V85005-0135

Not to be used for installation purposes. Issue 1.1

11-17-16

Annunciator loop (TB4)

The control panel provides a connection for up to eight serially

driven and supervised remote annunciators.

Circuit speciﬁcations

Device loops Class B (Style Y) or Class A (Style Z)

Circuit voltage 2.55 V

Circuit current 30 mA max

Circuit

impedance

Up to 8 annunciators or 4000 feet

–

TB4

–

Channel 1 Channel 2

CH1 (+) IN

CH1 (-) IN

CH2 (+) IN

CH2 (-) IN

Annunciator

–

TB4

–

Channel 1 Channel 2

CH1 (+) IN

CH1 (-) IN

CH2 (+) IN

CH2(-) IN

Annunciator

Terminal wiring location

–

TB4

–

Channel 1 Channel 2

CH1 (+) IN

CH1 (-) IN

CH2 (+) IN

CH2 (-) IN

Annunciator

–

TB4

–

Channel 1 Channel 2

CH1 (+) IN

CH1 (-) IN

CH2 (+) IN

CH2(-) IN

Annunciator

Terminal wiring location

Class B Class A

Alarm, trouble, and supervisory relay (TB3)

The trouble relay is normally-open, held closed,

and opens on any trouble event or when the

panel is de-energized. The supervisory relay is

normally-open, and closes on any supervisory

event. The alarm relay changes over on any

alarm event.

Relay speciﬁcations

Alarm Trouble Supervisory

Type Form C Form A

Voltage 24 VDC at 1 A resistive 24 VDC at 1 A resistive

Relay circuits can only be connected to power-limited sources.

Auxiliary & smoke power outputs (TB3)

The control panel provides two auxiliary power

outputs that can be used for powering ancillary

equipment such as remote annunciators and two

wire smoke detectors. Aux 2 can be software

selected to operate continuously. The circuit is

supervised for shorts and grounds.

Circuit speciﬁcations

Circuit voltage

range

21.9 to 28.3 V

Resettable circuit

(Aux power 2)

24 VDC nominal at 500 mA

Continuous circuit

(Aux power 1)

24 VDC nominal at 500 mA.

Use this circuit for powering

two-wire smoke detectors.

Note: Any current above 0.5 amp connected to both Aux

1 and 2 will reduce the total available NAC power by that

amount.

Notiﬁcation appliance circuits (TB2)

VS4 control panels come equipped with four notiﬁcation appliance

circuits. VS1 control panels come with two NACs. Each circuit can

be individually conﬁgured for continuous, temporal, synchronized,

and coded output.

Speciﬁcations VS4 VS1

Circuit Type 4 Class B or 2 Class A 2 Class B or 2 Class A

with SA-CLA module

Voltage 24 VFWR

Current 6.0 A total, 2.5 A max.

per circuit at 120/230

VAC 60 Hz.

5.0 A total, 2.5 A max.

per circuit at 230 VAC

50 Hz.

3.75 A total, 2.5 A max.

per circuit at 120/230

VAC 60 Hz.

3.0 A total, 2.5 A max.

per circuit at 230 VAC

50 Hz.

Impedance 26 Ω total, 0.35 µF max

EOLR 15 K Ω, ½ W

Synchronization Supported system-wide

NAC1 -

NAC2+

NAC2 -

NAC1+

EOLR

TB2

Class B wiring

TB2

TB6

EOLR

NAC3 -

NAC4+

NAC4 -

NAC3+

EOLR

NAC1 -

NAC2+

NAC2 -

NAC1+

Class A wiring

TB2

TB6

NAC1 -

NAC2+

NAC2 -

NAC1+

NAC1 -

NAC2+

NAC2 -

NAC1+

EOLR

TB2

Class B wiring

TB2

TB6

EOLR

NAC3 -

NAC4+

NAC4 -

NAC3+

EOLR

NAC1 -

NAC2+

NAC2 -

NAC1+

Class A wiring

TB2

TB6

NAC1 -

NAC2+

NAC2 -

NAC1+

Marking indicates output signal polarity when the circuit is active. Polarity reverses

when the circuit is not active. Wire notiﬁcation appliances accordingly. Notiﬁcation

appliance polarity shown in active state.

Wiring & Conﬁguration

Device loop

The system provides one device loop circuit with a total capacity

of 125 detectors and 125 module addresses. The loop circuit is

supervised for opens, shorts, and grounds.

Circuit

speciﬁcations VS4 VS1

Device loops One Class B or A

loop, supporting 125

detectors and 125

modules. Expandable to

four loops.

One Class B or A loop,

supporting 64 devices of

any kind.

Communication

line voltage

Maximum 20 V peak-to-peak

Circuit current 0.5 A max

Circuit

impedance

66Ω total, 0.5 µF, max

Isolators 64 maximum

Signal

Synchronization

Supported on a system-wide basis (all device loops)

when using an addressable notiﬁcation appliance

circuit (NAC) module and Genesis or Enhanced

Integrity notiﬁcation appliances.

Loop1SEC

Loop card

Loop1PRI

Loop

device

Loop

device

Data Line

Class B wiring

Class A wiring

Loop1SEC +

Loop1PRI

Loop

device

Loop

device

Loop card

Data Line

Loop1SEC

Loop card

Loop1PRI

Loop

device

Loop

device

Data Line

Class B wiring

Class A wiring

Loop1SEC +

Loop1PRI

Loop

device

Loop

device

Loop card Data Line

SLC A

SLC B

SLC A

SLC B

TB3

(1)

(4)

(3)

(2)

(1) Trouble

(2) Supervisory

(3) Alarm

(4) Smoke/Aux

Page 5 of 8 DATA SHEET V85005-0135

Not to be used for installation purposes. Issue 1.1

11-17-16

Single and Dual Loop Controller Cards

The V-SLC2-1 is a single loop controller card that can be used

with the VS1 as a replacement for the standard 64-point loop, or

with the VS4 as a 250-point expansion module.

The V-SLC2-2 is a 500-point dual loop controller card for the VS4

that provides two IDC circuits, each with 125 detector addresses

and 125 module addresses.

Speciﬁcations V-SLC2-1 V-SLC2-2

Device Addresses VS4: one loop, 250

device addresses

VS1: 64 addresses

VS4: two loops, 500

device addresses

Wiring Class B or Class A

Operating Voltage 24 VDC

Operating Current

(fully loaded loop)

Standby: 55 mA

Alarm: 80 mA

Standby: 45 mA

Alarm: 70 mA

Note: These ratings do not include the use of two-wire smoke modules.

Communication Line

Voltage

Max. 20.6 V peak-to-peak

Terminal Rating 12 to 18 AWG (0.75 to 2.5 mm2)

Circuit Current 0.5 A max.

Max total loop

resistance

66 Ω

Max total loop

capacitance

0.5 μF

Isolators 64 isolators maximum per loop (total both

isolator bases and modules)

Ground Fault

Impedance

0 to 5 kΩ

Operating

Environment

32 to 120°F (0 to 49°C)

0 to 93% noncondensing at 90°F (32°C)

RZI16-2 Remote Zone Interface Module

The RZI16-2 Addressable Remote Zone Interface Module is an

addressable device that provides connections for sixteen Class B

Initiating Device Circuits and two Class B Supervised Output

Circuits. The inputs and outputs can be conﬁgured individually for

several device types.

The RZI16-2 requires 18 consecutive addresses on the Signaling

Line Circuit (SLC). Addresses are assigned electronically. There are

no address switches to set.

The RZI16-2 incorporates two 8-segment DIP switches that are

used to select the Alarm or Supervisory default device type for

each of the 16 IDC circuits. The module also includes one 4-seg-

ment DIP switch used to select the default Relay or NAC output

device type. Device types other than the default are accomplished

through programming.

RZI16-2 Speciﬁcations

Voltage

24V/Aux nominal:

Supervisory current:

Alarm current:

24V/Aux minimum:

24V/Aux maximum:

NAC1, NAC2 nominal:

24 VDC

250 mA at 24 VDC nominal

1000 mA

18.4 VDC

26.4 VDC

24 VDC

Current

Standby current

for 4.7 k EOL (U.S.)

Standby current for

3.9 k EOL (Canada)

Alarm current

at nominal voltage

4.8 mA/ circuit

5.7 mA/ circuit

31.1 mA/ circuit

Relay outputs

Quantity

Type Rating (pilot duty)

Programmable 24 VDC at 2.5 A

Input circuit wiring

resistance

25 Ω per wire

Initiating device circuits

Quantity

EOL resistor

Zone voltage

Alarm current

Alarm impedance range

Trouble impedance range

4.7 kΩ (U.S.); 3.9 kΩ Canada

22.78 V for 4.7 kΩ (U.S.)

22.08 V for 3.9 kΩ (Canada)

31.1 mA/ channel at nominal voltage

< 680 Ω

> 5.55 kΩ

Supervised output circuits

EOL resistor

Quantity

Short circuit detection

Open circuit detection

Contact ratings

15 kΩ

< 2.6 kΩ

> 61.9 kΩ

24 VDC at 2.5 A (5 A for two NACs)

Compatible cabinets MFC(A), VS4, APS

SA-ETH Ethernet Interface Card

Network cable

Ethernet card

network

connection

SA-ETH wiring

The SA-ETH card provides a

standard 10/100 Base T Ether-

net network connection for

connecting to an intranet, a local

network, or the Internet. The

card can be used to download

conﬁguration programming from

the VS-CU to the panel.

The Ethernet card is installed on

the plastic assembly and con-

nects to the main circuit board

via a ribbon cable.

SA-ETH speciﬁcations

Ethernet 10/100 Base T

Operating environment

Temperature

Humidity

32 to 120°F (0 to 49°C)

0 to 93% RH, noncondensing at 90°F

(32°C)

Option Cards

Kidde VS Series panels are supported by a complete line of mod-

ules and related equipment that enhance performance and extend

system capabilities. Option cards plug directly into the control

panel main circuit board or are connected to it with a ribbon cable.

After installation, terminals remain accessible. The cabinet pro-

vides ample room for wire routing, keeping wiring neat at all times.

Page 6 of 8 DATA SHEET V85005-0135

Not to be used for installation purposes. Issue 1.1

11-17-16

SA-232 RS-232 interface

GND (black wire)

TXD (white wire)

RXD (red wire)

SA-232 wiring

The SA-232 card provides an RS-232 in-

terface with VS panels. It can be used for

connecting a printer to the control panel

to print system events. The card also

can be used for connecting a computer

to download a conﬁguration program

from the VS-CU to the control panel.

The RS-232 card is installed on the plas-

tic assembly and connects to the main circuit board via a ribbon

cable.

SA-232 speciﬁcations

Operating voltage Standard EIA-232

Terminal rating 12 to18 AWG (0.75 to 2.5 sq mm)

Operating environment

Temperature

Humidity

32 to 120°F (0 to 49°C)

0 to 93% RH, noncondensing at 90°F (32°C)

SA-DACT Dialer

The SA-DACT provides communications between the control

panel and the central station over a telephone line system. It

transmits system status changes (events) to a compatible digital

alarm communicator receiver over the public switched telephone

network. The dialer is capable of single, dual, or split reporting

of events to two different account and telephone numbers. The

modem feature of the SA-DACT can also be used for uploading

and downloading panel conﬁguration, history, and current status

to a PC running the VS-CU.

Phone line1

Phone line2

To wall

phonejac

Phone

cables

(supplied) RJ31jacks

SA-DACT

wiring

The dialer phone lines connect to

connectors on the dialer’s main

circuit board. Phone line 1 connects

to connector J4 and phone line 2

connects to connector J1.

The SA-DACT queues mes-

sages and transmits them based on priority (alarm, supervisory,

trouble, and monitor). Activations are transmitted before restora-

tions.

The SA-DACT is installed on the plastic assembly and connects to

the main circuit board via a ribbon cable.

SA-DACT speciﬁcations

Phone line type One or two loop-start lines on a public,

switched network

Phone line connector RJ-31/38X (C31/38X)

Communication formats Contact ID (SIA DC-05)

Operating environment

Temperature

Humidity

32 to 120°F (0 to 49°C)

0 to 93% RH, noncondensing at 90°F

(32°C)

Compatible DACRs

Receiver Models Formats

Ademco 685 Contact ID

FBII CP220 Contact ID

Osborne-Hoffman OH 2000 Contact ID

Bosch D6600 Contact ID

Silent Knight 9800 Contact ID

Sur-Gard SG-MLR1, MLR2 Contact ID

SA-CLA Class A Module (VS1 only)

The SA-CLA card provides Class A capability for NAC wiring.

Its terminal block provides the wiring connection for NAC return

wiring. The card is required for annunciator Class A wiring even

though this wiring does not return to the SA-CLA card. The SA-

CLA is compatible with VS1 control panels only. VS4 panels are

Class A Ready. The SA-CLA is installed directly to the control

panel circuit board using its plastic standoffs and plug connection.

SA-CLA speciﬁcations

Operating voltage 24 VFWR

Operating current 3.75 A FWR total at 120/230 VAC 60 Hz

3.0 A FWR total at 230 VAC 50 Hz

2.5 A max per circuit

Circuit impedance 26 ohms, 0.35uF

Terminal rating 12 to18 AWG (0.75 to 2.5 sq mm)

Operating environment

Temperature

Humidity

32 to 120°F (0 to 49°C)

0 to 93% RH, noncondensing at 90°F

(32°C)

D16L-VS LED Display Expander (VS4 only)

The D16L-VS LED Display Expanders provide LED annuncia-

tion for up to 16 zones. It provides two LEDs for each zone. Two

D16L-VS LED display expanders can be installed in each VS4

panel.

(1) LED 1

(2) LED 2

(3) LED Expander 1

(4) LED Expander 2

(5) Alarm/non-alarm

and trouble zone LEDs

Page 7 of 8 DATA SHEET V85005-0135

Not to be used for installation purposes. Issue 1.1

11-17-16

Speciﬁcations

VS1 VS4

Device loops 1 loop Class B or Class A (Styles 4, 6, 7) supporting up to

64 device addresses (any combination of detectors and

modules)

Maximum T-taps: 63

(each device can be on its own branch)

1 loop, expandable to 4, Class A or B (Styles 4, 6, 7),

each loop supporting up to 250 device addresses (125

detectors and 125 modules max.). Addresses 1 to 125 are

for detectors and addresses 126 to 250 are for modules

Maximum T-taps/loop: 124

Notiﬁcation appliance

circuits

2 Class B (Style Y), Class A (Style Z) optional

3.75 A FWR total at 120/230 VAC 60 Hz

3.0 A FWR total at 230 VAC 50 Hz

2.5 A FWR each max. per circuit

4 Class B (Style Y) or 2 Class A (Style Z)

6.0 A FWR total at 120/230 VAC 60 Hz

5.0 A FWR total at 230 VAC 50 Hz

2.5 A FWR each max. per circuit

Primary power 120 VAC, 60 Hz, 1.3 A max.

230 VAC, 50-60 Hz, 0.62 A max.

120 VAC, 60 Hz, 2.0 A max.

230 VAC, 50-60 Hz, 0.97 A max.

Base panel current standby 155 mA 172 mA

Base panel current alarm 204 mA 267 mA

Input zones 16 max. 32 max.

Remote annunciator 8 drops max., RS-485 Class B, Class A is optional

Data line length: 4,000 ft. (1,219 m)

8 drops max., RS-485 Class A or B

Data line length: 4,000 ft. (1,219 m)

Operating voltage 24 VDC panel

Auxiliary power output

circuit

Aux power 1: 500 mA, 24 VDC

Aux power 2: 500 mA, 24 VDC (1 A possible if you reduce total available NAC power by 500 mA)

Output: 28.3 to 21.9 VDC, special application

Note: For a list of compatible devices, see the VS1 and VS4 Series Compatibility List (P/N 3102354-EN)

Loop circuit Maximum loop resistance: 66 Ω

Maximum loop capacitance: 0.5 µF

Communication line voltage: Maximum 20.6 V peak-to-peak

Operating current (fully loaded loop) Stand by: 55 mA/45 mA

Alarm: 125 mA/115 mA (not including two-wire smoke modules)

Circuit current: 0.5 A max. Style 4, 6, and 7 wiring

Max. resistance between isolators: Limited only by overall wire run lengths

64 isolators maximum per loop (total both isolator bases and modules)

Batteries Type: Sealed lead acid

Voltage: 24 VDC

Charging current: 2.47 A max. Amp hour capacity: 26 Ah

Standby operation: 24 hour or 60 hour

Placement: Up to two 10 Ah batteries will ﬁt in the VS1 control panel cabinet and two 18 Ah batteries will ﬁt in the VS4

control panel cabinet. If larger batteries are required, use a battery cabinet.

SA-DACT dialer Phone line type: One or two loop-start lines on a public, switched network

Phone line connector: RJ-31/38X (C31/38X)

Communication formats: Contact ID (SIA DC-05)

Operating current Standby/Alarm: 41 mA Max.: 100 mA

FCC registration number: GESAL01BSADACT

Industry Canada Registration number: 3944A-SADACT

Ringer equivalence number: 0.1B

Ground fault impedance 0 to 5 kΩ

Alarm contact Form C N.O. 24 VDC at 1 A (resistive load)

Trouble contact Form C 24 VDC at 1 A (resistive load)

Supervisory contact Form A N.O. 24 VDC at 1 A (resistive load)

Environmental Temperature: 0 to 49°C (32 to 120°F) Relative humidity: 0 to 93% noncondensing

Terminal rating All terminals rated for 12 to 18 AWG (0.75 to 2.5 mm²)

Page 8 of 8 DATA SHEET V85005-0135

Not to be used for installation purposes. Issue 1.1

11-17-16

Technology that saves lives

Email: kidde.ﬁ[email protected]

Web: Kidde.com/EngineeredSystems

Kidde is a UTC brand.

1016 Corporate Park Drive

Mebane, NC 27302

Ordering Information

Part Description

VS4 Fire Alarm Systems

VS4-G Four loop system with one 250-point loop installed. 110v, gray door.

VS4-G-2 Four loop system with one 250-point loop installed. 230v, gray door.

VS4-G-2-PG Four loop system with one 250-point loop installed. 230v, gray door, Portuguese.

VS4-G-2-SP Four loop system with one 250-point loop installed. 230v, gray door, Spanish.

VS4-GC Four loop system, one 250-point loop installed. 110v, gray door, LED strips, Canada.

VS4-GD Four loop system, one 250-point loop installed. 110v, gray door, with dialer.

VS4-GF Four loop system, one 250-point loop. 110v, gray door, LED strips, French Canada.

VS4-G-PG Four loop system with one 250-point loop installed. 110v, gray door, Portuguese.

VS4-G-SP Four loop system with one 250-point loop installed. 110v, gray door, Spanish.

VS4-R Four loop system with one 250-point loop installed. 110v, red door.

VS4-R-2 Four loop system with one 250-point loop installed. 230v, red door.

VS4-RD Four loop system, one 250-point loop installed. 110v, red door, with dialer.

SA-TRIM2 VS4 Flush mount trim, black.

VS1 Fire Alarm Systems

VS1-G One loop system with one 64-point loop installed. 110v, gray door.

VS1-G-2 One loop system with one 64-point loop installed. 230v, gray door.

VS1-G-2-PG One loop system with one 64-point loop installed. 230v, gray door, Portuguese.

VS1-G-2-SP One loop system with one 64-point loop installed. 230v, gray door, Spanish.

VS1-GD One loop system, one 64-point loop installed. 110v, gray door, with dialer.

VS1-GL One loop system, one 64-point loop installed. 110v, gray door, English Canada.

VS1-GL-F One loop system, one 64-point loop installed. 110v, gray door, French Canada.

VS1-G-PG One loop system with one 64-point loop installed. 110v, gray door, Portuguese.

VS1-G-SP One loop system with one 64-point loop installed. 110v, gray door, Spanish.

VS1-R One loop system with one 64-point loop installed. 110v, red door.

VS1-R-2 One loop system with one 64-point loop installed. 230v, red door.

VS1-RD One loop system, one 64-point loop installed. 110v, red door, with dialer.

SA-TRIM1 VS1 Flush mount trim, black

Option Cards

V-SLC2-1 Expansion module, one 250-device loop. For VS4 only.

V-SLC2-2 Expansion module, two 250-device loops, 500 devices total. For VS4 only.

RZI16-2 Remote Zone Interface Module. 16 Class B IDCs, 2 Class B Output. Bracket included.

SA-DACT Dual Line Dialer/Modem, supports Contact ID, mounts in cabinet on base plate.

SA-232 RS-232 Serial Port for connection to printers & computers, mounts in cabinet.

SA-ETH Ethernet Port, Slave, mounts in cabinet on base plate.

SA-CLA Class A adapter module. Provides Class A capacity on NACs. Mounts in cabinet on

main board. VS1 systems only.

D16L-VS LED Annunciator module, 16 X 2-LED zones (4 programmable for sup). Mounts in

cabinet to right of LCD display. For VS4 only.

D8RY-VS Canada only: LED Annunciator module, two LEDs per zone, 16 zones (4 alarm only,

8 supervisory only, 4 alarm or supervisory). Mounts in cabinet. For VS4 only.

Accessories

CTM City Tie Module. 2-gang. Connection to a local energy ﬁre alarm box.

MFC-A Multifunction Fire Cabinet, 8" x 14" x 3.5" - red.

BC-1 Battery Cabinet. 14.0" x 18.25" x 7.25". Holds two 12V24A batteries.

BC-1R Battery Cabinet - Red. 14.0" x 18.25" x 7.25". Holds two 12V24A batteries.

GSA-REL Releasing Module

BC-1EQ Seismic hardening Kit for VS Series panels. Includes battery hardening for

BC-1 enclosure and components to harden panel internal components.

Programming Tools

VS-CU VS Series conﬁguration and diagnostics utility.

260097 RS232 cable, 4 conductor, DB9 PC interface

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere United Technologies Feueralarm Handbücher

United Technologies

United Technologies Kidde FX-270 Montageanleitung

Beliebte Feueralarm Handbücher anderer Marken

Zeta Alarm Systems

Zeta Alarm Systems INFINITY ID2 Bedienungsanleitung

System Sensor

System Sensor 22051TLE-RF-26 Bedienungsanleitung

Pittway

Pittway Notifier AM2020 Bedienungsanleitung

Ampac

Ampac ZoneSense Bedienungsanleitung

Kidde

Kidde VM-1 Produkthandbuch

LST

LST SIM016-3 Bedienungsanleitung

Fireboy- Xintex

Fireboy- Xintex FBD-MZ Originalbetriebsanleitung

bolid

bolid S2000-IP-03 Bedienungsanleitung

GST

GST DI-9204 Bedienungsanleitung

E2S

E2S BExTBG05D Bedienungsanleitung

Notifier

Notifier UZC-256 Bedienungsanleitung

Fire-Lite Alarms

Fire-Lite Alarms MS-2 Bedienungsanleitung

Siemens

Siemens FDOOT221 Bedienungsanleitung

hyfire

hyfire HY5000 Series Bedienungsanleitung

FlameStop

FlameStop PFSIFP8 Bedienungsanleitung

Radionics

Radionics Radionics 9124 Bedienungsanleitung

UniPOS

UniPOS FD 7120 Bedienungsanleitung

FIREWOLF

FIREWOLF FW-C01224 Bedienungsanleitung