UNV DC550 E Series Bedienungsanleitung
1
Video Decoders
Quick Guide
V1.00
2
1Overview
NOTE!
This manual describes the device hardware information and installation
procedure, and guides you through logging into the Web interface.
This series video decoders (referred to as device in this manual) are new
generation HD network video decoder terminals. The device is designed for remote
video surveillance and can be widely applied in various real-time surveillance
applications for monitoring videos remotely in real time.
1.1 Packing List
Please check the items in your package carefully. Contact your dealer if anything is
missing or damaged.
No.
Name
Qty
Unit
1
Decoder
1
PCS
2
Phoenix connector terminals
2 □4 □
PCS
3
Mounting brackets
1
Pair
4
Quick Guide
1
Set
5
Feet
4
PCS
6
Grounding Cable
1
PCS
7
Power Cable
0 □1 □
PCS
1.2 Appearance
Front view
3
LED description
LED
Status
Description
Running LED
Flashing
The device is starting up.
On
The device is operating.
Off
The device is shut down.
Alarm LED
On
At least one alarm, for example, temperature
alarm, is present.
Off
No alarm is present.
NET LED
On
A link to the Ethernet Interface is present.
Off
No link to the Ethernet Interface is present.
No 1-9 LED (DEC)
On
The device is displaying video.
Off
The device stops displaying video.
WIFI LED
-
Reservation.
Rear view
Interface description
Interface
Quantity
Description
HDMI IN
2
HOMI video input Interface.
HDMI OUT
4 or 6 or 9
HDMI video output interface.
4
Interface
Quantity
Description
Ethernet
interface
1
Used to connect to Ethernet to communicate with
the devices on the network, to receive IP camera
streams, and to be configured by the client through
Web interface.
10M/100M/1000M/auto-sensing, half duplex/full
duplex/auto-sensing, RJ-45 connector.
USB 3.0
1
USB 3.0 interface for upgrading equipment.
RS485
1
Serial port, used to interoperate with the connected
device, for example, to transmit transparent channel
data.
RJ-45 connector, four wires, supporting full duplex
and half duplex.
RS232
1
Serial interface, used to debug and maintain the
device.
RJ-45 connector.
ALM IN
6
The alarm input.
ALM OUT
3
The alarm output
LINE IN
1
Channel audio input.
LINE OUT
1
Track audio output.(RCA)
RST
1
Short press to restart,long press 5s to restore
factory Settings.
5
2Installing the Device
2.1 Preparation
2.1.1 Checking the Device Package
Before you install the device, verify the device model and check the components
and their quantity against the packing list to make sure all items listed are included
in the package.
WARNING!
Do not remove the dismantlement-preventive seal from the device chassis cover
without permission. To open the chassis, contact your dealer. Otherwise, we shall
not be held liable for any consequence caused thereby.
2.1.2 Checking the Installation Environment
The device can be installed indoors only, and must meet the following
requirements:
Use correct lightning protection devices for the device power source,
audio/video signals, and RS-485 interfaces.
Ground the device correctly through the grounding screw.
6
NOTE!
Equipment grounding shall be properly grounded through the specified
grounding terminal.( )
2.2 Starting Up the Device
After the cables are connected, connect the device with the power source, and
start up the device. Examine the device status according to Table 1-1.
3Logging In to and Out of the Device
You can manage and maintain the device through the Web interface.
Before you log into the device, verify that:
The device is operating correctly.
The network connection between the PC and the device is normal.
The PC is installed with Microsoft Internet Explorer 7.0 or higher.
The browser on the PC is not configured with the proxy server.
The default IP address of the device is 192.168.1.14, the subnet mask is
255.255.255.0, and the default gateway is 192.168.1.1.
For the first login, use admin as the username and 123456 as password.
To log into the Web interface:
1. Use the IE browser on your PC to visit the IP address of the device.
2. On the login page, enter your username and password to access the Web
interface.
You can select a menu item on the Web interface and select a tab to enter the
corresponding configuration page.
For information about the initial configuration and other parameter configurations,
7
see the online help by clicking the Help menu.
For the first login, you are recommended to change the default login password by
selecting Change Password.
To log out of the device, you can click the Exit menu and confirm your operation to
return to the login page.
Copyright Statement
©2020 Zhejiang Uniview Technologies Co., Ltd. All rights reserved.
No part of this manual may be copied, reproduced, translated or distributed in any form by
any means without prior content in writing from Zhejiang Uniview Technologies Co., Ltd
(referred to as Uniview or us hereafter).
The product described in this manual may contain proprietary software owned by Uniview and
its possible licensors. Unless permitted by Uniview and its licensors, no one is allowed to copy,
distribute, modify, abstract, decompile, disassemble, decrypt, reverse engineer, rent, transfer,
or sublicense the software in any form by any means.
Trademark Acknowledgements
are trademarks or registered trademarks of
Uniview.
All other trademarks, products, services and companies in this manual or the product
described in this manual are the property of their respective owners.
Export Compliance Statement
Uniview complies with applicable export control laws and regulations worldwide, including
that of the People's Republic of China and the United States, and abides by relevant
regulations relating to the export, re-export and transfer of hardware, software and
technology. Regarding the product described in this manual, Uniview asks you to fully
understand and strictly abide by the applicable export laws and regulations worldwide.
Privacy Protection Reminder
Uniview complies with appropriate privacy protection laws and is committed to protecting
user privacy. You may want to read our full privacy policy at our website and get to know the
ways we process your personal information. Please be aware, using the product described in
this manual may involve the collection of personal information such as face, fingerprint,
license plate number, email, phone number, GPS. Please abide by your local laws and
regulations while using the product.
About This Manual
This manual is intended for multiple product models, and the photos, illustrations,
descriptions, etc, in this manual may be different from the actual appearances, functions,
features, etc, of the product.
This manual is intended for multiple software versions, and the illustrations and
descriptions in this manual may be different from the actual GUI and functions of the
software.
Despite our best efforts, technical or typographical errors may exist in this manual. Uniview
cannot be held responsible for any such errors and reserves the right to change the manual
without prior notice.
Users are fully responsible for the damages and losses that arise due to improper
operation.
1
Uniview reserves the right to change any information in this manual without any prior
notice or indication. Due to such reasons as product version upgrade or regulatory
requirement of relevant regions, this manual will be periodically updated.
Disclaimer of Liability
To the extent allowed by applicable law, in no event will Uniview be liable for any special,
incidental, indirect, consequential damages, nor for any loss of profits, data, and
documents.
The product described in this manual is provided on an "as is" basis. Unless required by
applicable law, this manual is only for informational purpose, and all statements,
information, and recommendations in this manual are presented without warranty of any
kind, expressed or implied, including, but not limited to, merchantability, satisfaction with
quality, fitness for a particular purpose, and noninfringement.
Users must assume total responsibility and all risks for connecting the product to the
Internet, including, but not limited to, network attack, hacking, and virus. Uniview strongly
recommends that users take all necessary measures to enhance the protection of network,
device, data and personal information. Uniview disclaims any liability related thereto but
will readily provide necessary security related support.
To the extent not prohibited by applicable law, in no event will Uniview and its employees,
licensors, subsidiary, affiliates be liable for results arising out of using or inability to use the
product or service, including, not limited to, loss of profits and any other commercial
damages or losses, loss of data, procurement of substitute goods or services; property
damage, personal injury, business interruption, loss of business information, or any special,
direct, indirect, incidental, consequential, pecuniary, coverage, exemplary, subsidiary
losses, however caused and on any theory of liability, whether in contract, strict liability or
tort (including negligence or otherwise) in any way out of the use of the product, even if
Uniview has been advised of the possibility of such damages (other than as may be
required by applicable law in cases involving personal injury, incidental or subsidiary
damage).
To the extent allowed by applicable law, in no event shall Uniview’s total liability to you for
all damages for the product described in this manual (other than as may be required by
applicable law in cases involving personal injury) exceed the amount of money that you
have paid for the product.
Network Security
Please take all necessary measures to enhance network security for your device.
The following are necessary measures for the network security of your device:
Change default password and set strong password: You are strongly recommended to
change the default password after your first login and set a strong password that includes
at least 9 characters including uppercase letter, lowercase letter, digit and special character.
Keep firmware up to date: It is recommended that your device is always upgraded to the
latest version for the latest functions and better security. Visit Uniview's official website or
contact your local dealer for the latest firmware.
The following are recommendations for enhancing network security of your device:
2
Change password regularly: Change your device password on a regular basis and keep the
password safe. Make sure only the authorized user can log in to the device.
Enable HTTPS/SSL: Use SSL certificate to encrypt HTTP communications and ensure data
security.
Enable IP address filtering: Allow access only from the specified IP addresses.
Minimum port mapping: Configure your router or firewall to open a minimum set of ports
to the WAN and keep only the necessary port mappings. Never set the device as the DMZ
host or configure a full cone NAT.
Disable the automatic login and save password features: If multiple users have access to
your computer, it is recommended that you disable these features to prevent unauthorized
access.
Choose username and password discretely: Avoid using the username and password of
your social media, bank, email account, etc, as the username and password of your device,
in case your social media, bank and email account information is leaked.
Restrict user permissions: If more than one user needs access to your system, make sure
each user is granted only the necessary permissions.
Disable UPnP: When UPnP is enabled, the router will automatically map internal ports, and
the system will automatically forward port data, which results in the risks of data leakage.
Therefore, it is recommended to disable UPnP if HTTP and TCP port mapping have been
enabled manually on your router.
SNMP: Disable SNMP if you do not use it. If you do use it, then SNMPv3 is recommended.
Multicast: Multicast is intended to transmit video to multiple devices. If you do not use this
function, it is recommended you disable multicast on your network.
Check logs: Check your device logs regularly to detect unauthorized access or abnormal
operations.
Physical protection: Keep the device in a locked room or cabinet to prevent unauthorized
physical access.
Isolate video surveillance network: Isolating your video surveillance network with other
service networks helps prevent unauthorized access to devices in your security system
from other service networks.
Learn More
You may also obtain security information under Security Response Center at Uniview's official
website.
Safety Warnings
The device must be installed, serviced and maintained by a trained professional with
necessary safety knowledge and skills. Before you start using the device, please read through
this guide carefully and make sure all applicable requirements are met to avoid danger and
loss of property.
Storage, Transportation, and Use
Store or use the device in a proper environment that meets environmental requirements,
including and not limited to, temperature, humidity, dust, corrosive gases, electromagnetic
radiation, etc.
Make sure the device is securely installed or placed on a flat surface to prevent falling.
Unless otherwise specified, do not stack devices.
Inhaltsverzeichnis
Andere UNV Medienkonverter Handbücher
