Uponor BT DP-01 Bedienungsanleitung

Wireless thermostat

user guide

DE BEDIENUNGSANLEITUNG

DK BRUGERVEJLEDNING

FR GUIDE D’UTILISATION

NL HANDLEIDING

SE BRUKSANVISNING

05 I 2014

WIRELESS THERMOSTAT USER GUIDE

IMPORTANT!

Before starting work the installer should carefully read this Installation &

Operation Manual, and make sure all instructions contained therein are

understood and observed.

- The thermostat should be mounted, operated and maintained by specially

trained personnel only. Personnel in the course of training are only allowed

to handle the product under the supervision of an experienced fitter. Subject

to observation of the above terms, the manufacture shall assume the liability

for the equipment as provided by legal stipulations.

- All instructions in this Installation & Operation manual should be observed

when working with the controller. Any other application shall not comply with

the regulations. The manufacturer shall not be liable in case of incompetent

use of the control. Any modifications and amendments are not allowed for

safety reasons. The maintenance may be performed by service shops

approved by the manufacturer only.

- The functionality of the controller depends on the model and equipment.

This installation leaflet is part of the product and has to be obtained.

APPLICATION

- The thermostats of the “BT” series are developed to control and manage all

type of heating installations.

- The controllers have been designed for use in residential rooms, office

spaces and industrial facilities.

Verify that the installation complies with existing regulations before operation

to ensure proper use of the installation.

SAFETY INSTRUCTIONS

Before starting work disconnect power supply!

- All installation and wiring work related to the thermostat must be carried

out only when de-energized. The appliance should be connected and

commissioned by qualified personnel only. Make sure to adhere to valid

safety regulations.

- The thermostats are neither splash- nor drip-proof. Therefore, they must

be mounted at a dry place.

- Do not interchange the connections of the sensors and the 230V

connections under any circumstances! Interchanging these connections may

result in life endangering electrical hazards or the destruction of the

appliance and the connected sensors and other appliances.

WIRELESS THERMOSTAT USER GUIDE

Table of content

1 Presentation........... 4

1.1 Keyboard............... 5

1.2 Display & LED......... 5

2 First Installation ..... 6

2.1 Batteries installation 6

2.2 Time and Date adjustment 7

2.3 RF installation ........ 7

2.4 Starting................. 8

3 Working mode definition 9

3.1 Manual mode Comfort 9

3.2 Manual mode, Reduced 10

3.3 OFF mode ............. 10

3.4 Automatic mode ..... 10

3.5 Program mode ....... 10

3.6 Holiday mode......... 15

3.7 Timer mode .......... 15

4 Special function...... 16

4.1 Keyboards lock Function 16

4.2 Information............ 16

5 Parameter’s menu... 17

6 Technical characteristics 19

7 Troubleshooting & Solution 20

WIRELESS THERMOSTAT USER GUIDE

1 Presentation

Electronic programmable thermostat with LCD display specially designed to

control different type of heating systems.

It will be your best partner to optimize your energy consumption and

increase your comfort.

- Modern design with soft touch material

- Wiring & Installation simplified

- “Easy program creation” function

- Weekly programmable by step of 30 min

- Temporary override function

- Anti-freeze function

- Holiday or Reception function

- EEPROM non-volatile memory

- 2 AAA batteries for 2 years operating life

- 2 Wires output for a maximum possibility of use

- 2 parameter menus (user and installer)

In option

- External sensor with several possibilities of regulation (floor, combined…)

WIRELESS THERMOSTAT USER GUIDE

1.1

Keyboard

Left Navigation key (

◄

)

Right navigation key (

►

)

Escape key ()

Edition key ()

1.2

Display & LED

Red Fix (when backlight is lit up): Heating demand

Green flash: your validation is required

Red flash: Error on sensor or batteries

Current day of the week

Operating mode menu (active mode is framed).

Minus Key (-) Plus Key (+)

Validation Key (OK) Status LED

1 2

12 11 10

WIRELESS THERMOSTAT USER GUIDE

Program number or parameter number if “4” is displayed.

Installation Parameter menu.

RF transmission logo.

Type of sensor used and temperature displayed.

Regulation => Internal or external ambient sensor.

Regulation => Floor sensor.

Regulation => Internal sensor with Floor limitation.

View of the outside temperature

Heating demand indication.

Low batteries indicator.

°C or °F unit indicator

10.

Setting or measured temperature if “5” is displayed. Parameter value if

“4” is displayed.

11.

Temporary override function activated, or “ITCS” function if blinking.

12.

Time or parameter title if “4” is displayed.

13.

Program of the current day (the current time bar blinks)

14.

Pictogram for program creation, program state in normal operating

mode.

15.

Key lock indicator

First Installation

This section will guide you to set up your thermostat for the first time.

2.1

Batteries installation

- Open the two side’s covers and Insert the 2 AAA Alkaline supplied batteries

(or remove the small protection sticker if the batteries are already installed

in the compartment)

- Close the two side’s covers.

- Now your thermostat will propose you to adjust the current time and date.

WIRELESS THERMOSTAT USER GUIDE

2.2

Time and Date adjustment

Each time a value blinks, you can adjust it with the (-) and (+) keys, once

the value is chosen, validate it with the (OK) key. The thermostat will jump

automatically to the next value.

Note: you can always come back to the previous value by pressing the

escape key ().

List order of the time and date adjustments:

Time and day:

Adjustment of the hours,

Adjustment of the minutes

Adjustment of the day (1 = Monday)

Date:

Adjustment of the day number

Adjustment of the month number (01 to 12)

Adjustment of the year (Century)

Adjustment of the year

Then the message “Save” and blinking green LED appears, press (OK) to

validate the adjusted time and date.

You can always reach the time and date adjustments, by pressing and

maintaining the edition ()key during 2 seconds in normal operating modes.

2.3

RF installation

- First of all to configure your thermostat with the receiver, you must put

your receiver in « RF init ». mode. (please refer to the receiver leaflet for

this, only the RF receiver of the same range are compatibles)

- Now on the thermostat press and maintain the edition key ()during 10s,

then the parameter « ini » must be display.

The thermostat will send now the radio configuration signal to the receiver.

- On the receiver check the good reception (generally showed by a green

LED blinking). Once the configuration between the receiver and the

thermostat made, press on the escape key ( ) to come back to the main

screen.

WIRELESS THERMOSTAT USER GUIDE

- Now you can check the RF distance, go to the room which must be

regulated. Put your thermostat on the final position (On the wall or

table...), then put the thermostat in Comfort mode (setting temperature

position 37°C). Close the door and go to the receiver to check if the new

status of the thermostat has received. (The heating is generally showed by

a Red LED).

- Now return to the thermostat and switch off it. Check on the receiver again

if it’s also switched off (The red LED must be turned off)

oIf the RF signals were received correctly, adjust your setting temperature

as you want.

oIf the RF signals weren’t received correctly, check the installation

(Receiver position, distance...)

* To make the installation easier it will be better to have the thermostat near

to the receiver during the configuration mode. (A minimal distance of >

1 meter must be respected)

2.4

Starting

The thermostat is now ready to works.

The default working mode will be automatic with a standard built-in

program “P1”.

Monday to Friday

20°C

18°C

07:00 09:00 17:00 23:00

Saturday & Sunday

20°C

18°C

08:00 23:00

WIRELESS THERMOSTAT USER GUIDE

Note:

You can customise your program as you want, See the next part “Working

mode definition” chapter “Program” for more explanation

At any time, when the backlight is extinct, press the (OK) key to lit-up the

backlight,

and then press another time the (OK) key to show the current

setting temperature.

Working mode definition

How to change the working mode?

- Open the small center cover to have access to the navigation keys (

◄

)or

(

►

- You can now press theses keys to display the working mode line.

Move the frame cursor on the desired working mode and press (OK) to enter

in the operating mode you have chosen.

3.1

Manual mode Comfort

Manual working mode, the comfort setting temperature will be followed all

the time.

By pressing (-) or (+) keys, the comfort setting temperature starts to blink

and can be adjusted.

Curent stage

of the program

Curent time

Program

followed

WIRELESS THERMOSTAT USER GUIDE

3.2

Manual mode, Reduced

Manual working mode, the reduced setting temperature will be followed all

the time.

By pressing (-) or (+) keys, the reduced setting temperature starts to blink

and can be adjusted.

3.3

OFF mode

Use this mode if you need to switch off your installation.

Be Careful:

In this mode your installation can freeze.

- At any time, when display is off, press on the (Ok) key to display a few

seconds the current temperature and time.

- To restart your installation, use the navigation keys (

◄

)or (

►

3.4

Automatic mode

In this mode the thermostat will follow the chosen program (Built-in or

customized) according to the actual time and the Comfort and Reduced

setting temperatures.

You can easily override, until next program step, the current program

temperature by changing the value with (-) or (+). Setting temperature will

blink.

The small hand logo will be displayed when override function is active.

If hand logo blinks then ITCS is ongoing.

3.5

Program mode

When you enter in the Program mode, the first operation is to choose the

program number

with (-) or (+) keys.

Current day

Program

of the day

Program

followed

Inhaltsverzeichnis

Sprachen:

Andere Uponor Thermostat Handbücher

Uponor

Uponor 1121082 Montageanleitung

Uponor

Uponor Smatrix Move Bedienungsanleitung

Uponor

Uponor Climate Control Zoning System II Bedienungsanleitung

Uponor

Uponor A3030102 Bedienungsanleitung

Uponor

Uponor T-87IF Handbuch

Uponor

Uponor T-54 Bedienungsanleitung

Uponor

Uponor Comfort E T-87IF Handbuch

Uponor

Uponor T-85 Bedienungsanleitung

Uponor

Uponor Climate Control Betriebsanleitung

Uponor

Uponor Ecoflex Supra Standard ETN4 Bedienungsanleitung

Uponor

Uponor SetPoint 521 Bedienungsanleitung

Uponor

Uponor Comfort E T-87IF Bedienungsanleitung

Uponor

Uponor T-27 Bedienungsanleitung

Uponor

Uponor Comfort E T-87IF Handbuch

Uponor

Uponor T-25 Bedienungsanleitung

Uponor

Uponor SetPoint 521 Bedienungsanleitung

Uponor

Uponor T-27 Bedienungsanleitung

Uponor

Uponor Comfort-E Bedienungsanleitung

Uponor

Uponor T-26 230 V Bedienungsanleitung

Uponor

Uponor T-26 Bedienungsanleitung

Uponor

Uponor T-26 Bedienungsanleitung

Uponor

Uponor Smatrix Move PLUS Bedienungsanleitung

Uponor

Uponor SetPoint 521 Bedienungsanleitung

Uponor

Uponor Climate Control Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Honeywell

Honeywell CM721 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

Honeywell

Honeywell RLV4305 Bedienungsanleitung

Honeywell

Honeywell Prestige 2.0 THX9421 Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung