US Robotics USR2249 Bedienungsanleitung

22 Mbps Wireless Access Point

Quick Installation Guide

Note: For the most updated information, visit: http://www.usr.com/

support. You can also refer to the User Guide on the U.S. Robotics

Installation CD-ROM for more detailed information.

Prepare for installation

Turn on your desktop or laptop computer. Type your password if you are

prompted to do so.

Note: Your product number is 2249. It is very important that you have your

serial number written down before you install the 22 Mbps Wireless

Access Point. You can find your serial number on the bottom of the

Wireless Access Point and on the side of the package. If you ever need to

call our Technical Support department, you will need this number to

receive assistance.

Serial Number

R24.0277.00

Note: Be sure to find out what letter your CD-ROM drive uses before you

begin installing your new product. You will need to know this to properly

install your software.

Install your software

Attention: You will need to install this software on all the PCs or

laptops you plan to wirelessly network together.

Insert your U.S. Robotics Installation CD-ROM into your CD-ROM drive.

Note: If the Choose Setup Language window appears, select your

preferred language and click OK.

Note: If your CD-ROM does not automatically launch, click Windows

Start, Run, and type D:\setup (or the appropriate letter of your CD-

ROM drive) and click OK.

Some files will be copied to your system, and then you will be asked to read the

license agreement. Read the agreement and click Yes.

The Installation CD Graphic User Interface (GUI) will appear on your screen.

Click Software.

Click Install Access Point Software. Follow the on-screen instructions and wait

for some files to be copied to your hard drive. A window will appear showing

you the files that are being loaded onto your system. When you are prompted to

reboot your computer, select Yes, I want to restart my computer now and click

Finish. After your computer reboots, the program window with the Configura-

tion Utility icons may appear. Close this window. When the Menu screen of the

U.S. Robotics Installation CD-ROM returns, close it.

Remove the Installation CD-ROM and prepare to install your hardware.

Connect the 22 Mbps Wireless

Access Point

•Use the Ethernet port and an RJ-45 cable to connect the 22 Mbps Wireless

Access Point to one of the following devices: a cable or DSL modem with

routing capabilities, a hub, a bridge, an existing Ethernet LAN, or a router.

•Attach the power supply to the Wireless Access Point and to a power

outlet.

The Wireless Access Point has three LED status indicators, LINK, DATA, and

POWER. When the Wireless Access Point is plugged in, the PWR LED will

illuminate. When a network connection is established, the LINK LED will be

green. When there is network activity, the DATA LED will be yellow.

Verify detection of the 22 Mbps Wireless

Access Point

After the Wireless Access Point is installed, double-click the icon for

the Configuration Utility on your desktop. If the 22 Mbps Wireless

Access Point is correctly installed, the configuration information

will be displayed.

To verify that you are connecting to the correct Wireless Access Point, check the

MAC address. The MAC address is located on the bottom of the 22 Mbps

Wireless Access Point case and in the Link Information option of the Configura-

tion Utility.

When you have identified the correct Wireless Access Point, note the IP address

that is listed. Launch a Web browser on the computer that is physically

connected to the 22 Mbps Wireless Access Point. Enter the IP address for your

Wireless Access Point. This will open the Web Configuration Utility. There is no

default username or password, so just click OK when you are prompted.

When the Web Configuration Utility launches, you can change the information

about your wireless network. For more information about both Configuration

Utilities for the 22 Mbps Wireless Access Point, refer to the User Guide on the

Installation CD-ROM.

Note: If you need to reset the Wireless Access Point at any time,

perform the following steps. Press in and hold the RESET button. While

holding in the RESET button, unplug the power adapter from the

Wireless Access Point and then plug it back in. Continue to hold the

RESET button for about five seconds to restore the factory default

settings. When this is performed, the PWR LED will blink.

Attention: If you reset the Wireless Access Point, you will lose your

custom settings.

Congratulations! You have finished installing your hardware and the

necessary software. You should now be able to connect your Wireless Access PC

Cards and PCI Adapters to the Wireless Access Point.

For more detailed information about the installation procedure, the Access

Point Web Configurator, Troubleshooting, and Technical Support, refer to the

User Guide on the Installation CD-ROM.

Printed in Taiwan

Inhaltsverzeichnis

Andere US Robotics Drahtloser Zugangspunkt Handbücher

US Robotics

US Robotics MAXg Bedienungsanleitung

US Robotics

US Robotics USR5453 Bedienungsanleitung

US Robotics

US Robotics USR5450 Bedienungsanleitung

US Robotics

US Robotics USR5450 Bedienungsanleitung

US Robotics

US Robotics USR5453 Bedienungsanleitung

US Robotics

US Robotics USR2450 Bedienungsanleitung

US Robotics

US Robotics USR805453A Bedienungsanleitung

US Robotics

US Robotics USR2450 Bedienungsanleitung

US Robotics

US Robotics MAXg Bedienungsanleitung

US Robotics

US Robotics Instant802 APSDK Service-Handbuch

US Robotics

US Robotics USR5451 Bedienungsanleitung

US Robotics

US Robotics USR8054 Bedienungsanleitung

US Robotics

US Robotics USR2450 Bedienungsanleitung

US Robotics

US Robotics USR8054 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung