Utah Sandar UTAH-100 Montage- und Bedienungsanleitung

Utah Sandar

User Manual & Installation Guide

UTAH-100

X-SERIES

Routers and Distribution Amplifiers

User Manual & Installation Guide

UTAH-100 X-Series

Document: UTAH-100-X-Series.doc

Date: 2009-11-10, Rev. 1.0

CONTENTS

Quick Start Guide

Routers

Analog Video

Analog Audio

Distribution Amplifiers

Analog Video

Analog Audio

Software Installation and Operation

Utah Sandar

User Manual

UTAH-100/X16HD

16x16, 8x8 SDI-HD 3Gb/s Router with/without

Control Panel

UTAH-100/X16HD, UTAH-100/X16HDCP,

UTAH-100/X8HD, UTAH-100/X8HDCP

User Manual & Installation Guide

UTAH-100/X HD Series

3213-User10.doc

Date: 2009-10-07, Rev. 1.0

CONTENTS

CONTENTS .............................................................................................................................................................. 2

INTRODUCTION ..................................................................................................................................................... 3

WARRANTY............................................................................................................................................................. 3

DOCUMENT REVISION HISTORY ...................................................................................................................... 3

SAFETY & ENVIRONMENT.................................................................................................................................. 4

GENERAL ............................................................................................................................................................... 4

SAFETY SYMBOLS ................................................................................................................................................. 4

SAFETY EARTH GROUND ...................................................................................................................................... 4

ENVIRONMENT ....................................................................................................................................................... 4

INSTALLATION....................................................................................................................................................... 5

INITIAL INSPECTIONS.............................................................................................................................................. 5

ESD HANDLING ..................................................................................................................................................... 5

BEFORE APPLYING POWER................................................................................................................................... 5

SERVICE................................................................................................................................................................. 5

GENERAL DESCRIPTION .................................................................................................................................... 6

EXTERNAL POWER SUPPLY .................................................................................................................................. 7

UTAH-100 CONTROL SOFTWARE: ................................................................................................................... 7

PINOUT..................................................................................................................................................................... 7

POWER CONNECTION............................................................................................................................................ 7

PORT PIN ORIENTATION ........................................................................................................................................ 7

SPECIFICATIONS................................................................................................................................................... 9

BLOCK DIAGRAM................................................................................................................................................ 10

MODEL UTAH-100/X16HD................................................................................................................................10

MODEL UTAH-100/X16HDCP .......................................................................................................................... 11

MODEL UTAH-100/X8HD.................................................................................................................................. 12

MODEL UTAH-100/X8HDCP ............................................................................................................................ 13

User Manual & Installation Guide

UTAH-100/X HD Series

3213-User10.doc

Date: 2009-10-07, Rev. 1.0 3

Utah Sandar

Thorøyaveien 11

N-3209 Sandefjord,

Norway

Tel.: +47 33 52 27 00

Fax: +47 33 52 27 01

INTRODUCTION

Thank you for choosing a Utah Sandar product.

We are convinced that your choice will prove to be a wise

and worthy decision for many years to come.

Your Utah Sandar product has been tested for performance at the

factory according to the specifications given for the system in this

manual. However, before putting the device into

operation we kindly ask you to read this manual, and

act according to the information given.

All information given in this document is property of Utah

Sandar. To the knowledge of Utah Sandar there are no

errors in the manual. Should any errors be discovered,

please notify Utah Sandar. Utah Sandar will under no

circumstances accept responsibility neither for errors in this

manual, nor consequences of such errors.

WARRANTY

This Utah Sandar product is warranted against defects in materials and workmanship for a period of two

(2) years from the date of invoice. During the warranty period, Utah Sandar will, at its option, either

repair or replace products that prove to be defective.

The warranty shall not apply to defects resulting from improper or inadequate installation or

maintenance by buyer, buyer-supplied software or interfacing, unauthorized modification or misuse,

operation outside of the environmental specifications for the product, or improper site preparation or

maintenance.

If a product needs to be returned for service, please first contact the Utah Sandar Helpdesk to obtain a

Return Material Authorization (RMA) number. Make sure the packaging provides sufficient protection

against ESD and mechanical damage. Please enclose a note with the RMA, return address, contact

person details and a failure symptom description.

DOCUMENT REVISION HISTORY

Rev. Date Description

1.0 2009-10-07 Changed product name

B 2008-12-22 Change name and logo

A 2008-04-30 Preliminary

User Manual & Installation Guide

UTAH-100/X HD Series

3213-User10.doc

Date: 2009-10-07, Rev. 1.0

SAFETY & ENVIRONMENT

General

This product and related documentation must be reviewed for familiarization with safety markings and

instructions before operation. This product has been designed and tested in accordance with the

relevant international standards.

Safety Symbols

Indicates hazardous voltages.

Indicates earth (ground) terminal.

The CAUTION sign denotes a hazard. It calls attention to an operating procedure,

practice, or the like, which if not correctly performed or adhered to could result in

damage to or destruction of part or all of the product. Do not precede beyond a

CAUTION sign until the indicated conditions are fully understood and met.

STOP

The WARNING sign denotes a hazard. It calls attention to a procedure, practice, or the

like, which, if not performed or adhered to could result in personal injury. Do not proceed

beyond a WARNING sign until the indicated conditions are fully understood and met.

Safety Earth Ground

This is a Safety Class 1 product (a protective earth terminal (Ch) is provided).

An uninterrupted safety earth ground must be provided from the main power source to the product input

wiring terminals, power, cord, or supplied power cord set. Whenever it is likely that the protection has

been impaired, the product must be made inoperative and secured against any unintended operation.

Environment

WEEE: All Utah Sandar products will comply with the EU Directive 2002/96/EC on

Waste from Electrical and Electronic Equipment aka WEEE directive. Please contact

your local Utah Sandar sales representative for information about returning these

products for safe disposal/recycling. Utah Sandar equipment that complies with the

directive will be marked with a WEEE-compliance emblem.

RoHS: All Utah Sandar products will comply with the EU Directive 2002/95/EC on

Restriction of Hazardous Substances aka RoHS directive. Thereby not containing above

the limits specified in the said directive of any of the banned substances. Utah Sandar

equipment that complies with the directive will be marked with a RoHS-compliance

emblem.

Exempt: Spare/Expansion parts for older systems are exempt from the directive.

User Manual & Installation Guide

UTAH-100/X HD Series

3213-User10.doc

Date: 2009-10-07, Rev. 1.0 5

INSTALLATION

Initial Inspections

Check the contents of the shipment for completeness and possible transport damage.

If the contents are incomplete or damaged, contact Utah Sandar AS immediately for repairing or

replacement parts of the equipment.

ESD Handling

This product may contain Electrostatic Sensitive Devices (ESD).

Precautions to minimise the risk of damage, due to electrostatic discharge during

handling, are recommended. For guidance, refer to British Standard BS CECC 00015,

Part 1:

BASIC SPECIFICATION FOR PROTECTION OF ELECTROSTATIC SENSITIVE DEVICES

Before Applying Power

Verify that the product is configured to match the available main power source per the

input power configuration instructions provided in this manual and product marking.

STOP

Service

Servicing, adjustments, maintenance or repair of this product may be performed by

qualified personnel only. Adjustments described in this manual may be performed with

power supplied to the product while protective covers are removed. Energy available at

many points may, if contacted, result in personal injury. Capacitors inside this product

may still be charged even when disconnected from their power source.

User Manual & Installation Guide

UTAH-100/X HD Series

3213-User10.doc

Date: 2009-10-07, Rev. 1.0

GENERAL DESCRIPTION

The UTAH-100/X16HD Compact HD/SDI Router fully complies with the relevant standards for SD-,

HD- and 3G-SDI (SMPTE 259M, 292M and 424M) formats. With adaptive cable equalizers, signal re-

clocking, cable drivers and multi-sync reference switching these routers are well suited for OB vans and

all other digital Broadcast and Telecom routing and distribution systems. Having both an Ethernet

SNMP/HTTP/SanEth) and DSUB9P RS-232 interface for remote control and configuration makes it very

adaptable to any 3rd party control system.

The UTAH-100/X16HD is delivered in four models:

Model UTAH-100/X16HD : 16x16 with 16 LEDs for signal presences in the front.

Model UTAH-100/X16HDCP : 16x16 with Push Buttons in the front 16 for outputs selection and 16

for input selection.

Model UTAH-100/X8HD : 8x8 with 8 LEDs for signal presences in the front.

Model UTAH-100/X8HDCP : 8x8 with Push Buttons in the front, 8 for outputs selection and 8 for

input selection.

All units are delivered with one standard off-the-shelf universal AC/DC Power Supply. Two

independent power inputs are provided to enable redundant supplies.

The 19” wide, 1RU high and 60 millimetres deep frame houses the switch, local control unit and RS-232

and Ethernet remote control interface. Two 12 VDC 2.1mm power input connectors enable use of

redundant power supplies.

UTAH-100/X16HD

UTAH-100/X16HDCP

UTAH-100/X8HD

UTAH-100/X8HDCP

User Manual & Installation Guide

UTAH-100/X HD Series

3213-User10.doc

Date: 2009-10-07, Rev. 1.0 7

External Power Supply

The external Power Supply is an AC/DC Switch Mode desktop power supply module with compact

design. The power supply has a universal input voltage, with 3 pins IEC 320 connector. The output

voltage is 13.2 VDC and is short circuit proof and deliver up to 40W. One secondary cable with the

modular connector in the one end connects to the power supply and the other end with a 5.5/2.1mm jack

connects to the UTAH-100/XHDA frame. Utah Sandar recommends the Power Supply 9920 from

Mascot A/S, but other types of Power Supplies may be used with similar specifications. Mains cord is

not included.

Mounting bracket is available.

UTAH-100 CONTROL SOFTWARE:

•For Quick Start Guide see the attached document in the delivery.

•UTAH-100 Control Software see the document file: UTAH-100-ControlSoftware10.pdf attached

in the user manual CD.

PINOUT

Power Connection

The UTAH-100/X16HD units have two 2.1mm DIN 12VDC connector with + at centre.

The power unit supplied with the UTAH-100/X16HD is a 13.2 VDC with a max rating of 3A (40W)

Port Pin Orientation

Ethernet Port

The Ethernet port is an 8-pin RJ-45 jack meeting the requirements of ISO 8877 for 10/100Base-T.

Ethernet Pin Assignment

Pin Signal Name Figure

RJ-45

1 TxD+ (Transmit Data)

2 TxD- (Transmit Data)

3 RxD+ (Receive Data)

4 Not used

5 Not used

6 RxD- (Receive Data)

7 Not used

8 Not used

User Manual & Installation Guide

UTAH-100/X HD Series

3213-User10.doc

Date: 2009-10-07, Rev. 1.0

RS-232 Port

Serial port, RS-232 is a DSUB9pin (male) connector. Use the following figure and tables for pin

orientation and pin assignment information.

Serial Pin Assignment

Port Signal

Pin1

Signal

Pin 2

Signal

Pin3

Signal

Pin4

Signal

Pin5

Signal

Pin6

Signal

Pin7

Signal

Pin 8

Signal

Pin 9

RS-

232

Not

connected

RxD TxD Not

connected

GND Not

connected

Not

connected

Not

connected

Not

connected

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Utah Sandar Netzwerk-Router Handbücher

Utah Sandar

Utah Sandar UTAH-100/X16V Montage- und Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Korenix

Korenix JetNet 5710G Series Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise